User Manual

FCC ID: 2AAV8QT-12

Users Manual

Download: PDF
FCCID_2058773

Names for Parts 5. Connect the product with proper power socket. 6. Warm up time is approximately 4 – 5 minutes. When fully heated, the Wired Control Indication USER MANUAL Light will turn on and the Fog Machine will be ready to produce and spray fog. 7. Set the On/Off Switch to on position on the Wired Control Box, nozzle will start spraying fog. 400 Watt Fog Machine Or you can remote control the Fog Machine to spray fog by the Remote Control Transmitter according to following sequence: Model No.: QT-12 a. Remove the battery insulation tab carefully. This is to activate the battery. The battery insulation tab is located at the back cover of the Remote Control Transmitter. It is very important to operate this product according to the following instructions. Failure to do b. Press and hold the Push Button on the Remote Control Transmitter within 10 meters, and the so may render your guarantee void. Wireless Remote Indication Light on the Transmitter will be on at the same time. Then the fog (D) machine will be spraying. Accessories List (C) Please be well noted: The product comes with (A) (B) (F) (E) ● The maximum transmitting distance is 10M in the open air. ● 1 x Product Body with Power Cable ● If you just press but not hold the Push Button on the remote control transmitter, the fog machine ● 1 x Wired Control Cable and Box would just spray very shortly and stop. It is necessary for you to hold the button if you want the ● 1 x Wireless Remote Control Transmitter with Battery Installed (K) (L) fog machine to spray continuously. ● 1 x User Manual (N) 8. Turn off the unit before refilling the fog machine. 9. Unplug the unit when not in use. (J) 10. To refill the tank; turn off the unit, unplug and follow the directions in Step 3. (I) (H) (M) (G) (O) (A) Spray Nozzle (B) Handle (C) Tank Lid (D) Product Cover (E) Wired Control Cable Interface (F) Fuse Knob Wired Control Remote Control User Manual (G) On/Off Switch (H) Wired Control Indication Light (I) Wired Control Box Product Body with Power Cable Cable and Box Transmitter (J) Wired Control Cable (K) Wireless Remote Indication Light (L) Push Button A: Fog Machine (M) Remote Control Transmitter (N) Screws (O) Battery Insulation Tab B: Wired Control Box and Cable Specifications C: Fog Liquid (not included) ● Power Sources : Input AC120V 60Hz How to Use? D: Power Cable ● Power Consumption: 450W Before using the fog machine, you have to prepare Fog Liquid (not included). Then operate ● Warm Up Time: 3-5 Minutes according to following sequence. ● Tank Capacity:300ml 1. Remove all the packages. Additional Information ● Fog Output: 2,000CFM (a) It is normal if there is condensation on the nozzle of the Fog Machine. 2. Carefully put this product onto a clean, flat and solid surface, close to the power socket. ● Output Distance: ≥2M (b) A small amount of fog may spray during or after operation. 3. Unscrew the lid on the tank by turning counterclockwise and pour the Fog Liquid inside. Do not ● Output Time: ≥40s (c) The Fog Machine will have to reheat after long spray. It will stop operation for a short period in spill Fog Liquid onto the product body. Do not overfill. If liquid gets into the Fog Machine, leave it ● Outline Size: 250x187x202mm order to heat up to operating temperature again. While this is happening, fog cannot be to be dry completely before plugging in. Do not cut, pinch, or break the tube connected through ● Fuse: 5A, 125V produced. The Wired Control Indication Light will turn on again when the unit is ready to the tank lid. Screw the lid clockwise to the tank tightly. Always make sure there is enough Fog ● Remote Control Distance: Maximum 10M in the open air generate more fog. Liquid in the tank before using the Fog Machine. ● Remote Control Transmitter Battery: 1×23A 12V (d) All fog machines are apt to clogging due to the consistency of Fog Liquid and the high 4. Connect the wired control cable to the Interface at the back of the Fog Machine. temperatures at which it vaporizes. 1 2 3 Maintenance and Cleaning ● Keep away from the spray nozzle at least 0.5 meters when the nozzle spraying fog. ● Maintenance and cleaning shall only be done to the product surface. Unplug this product from ● Attention! Do not place the product onto wet or uneven surfaces. Accidental falls may cause fire. the power socket before cleaning. ● The product shall be changed if it has become damaged or thermally deformed. Disconnect this ● Do not wet any electric parts of this product. Please use a dry, soft cloth instead of sharp tools for product from power immediately in case of malfunction. Do not resume use until it’s repaired. cleaning. ● Do not use the Fog Machine or Remote Control Transmitter outdoors. They are not waterproof. ● If you find there is low fog output after many hours of continuous operation or after the machine ● This product is not a toy. Please keep this unit out of reach of children and pets. has been idle or in storage for a long time, it is advised to empty all Fog Liquid from the machine ● Close supervision is necessary when this product is used by invalids, or disabled persons, or near and clean the tank. Please unplug the machine from power socket before cleaning. children. ● Use this product only for its intended use as described in these instructions. Do not use Replace Battery for the Remote Control Transmitter attachments not recommended by the manufacturer. If the Remote Control Transmitter does not work at all within the working distance, it is probably ● Keep the power cable away from heated surfaces. that the battery has been run-out. Please replace the used battery with a new one. ● Never drop or insert any object into any opening. Note: Before replacement, you need to prepare a small cross-headed screw driver and a new battery ● Please unplug the power cable if you want to stop use of this unit for long time. with correct specification: 23A 12V ● The external flexible cable of this product cannot be replaced; if the power cable is damaged, the 1. Unscrew the 3 screws at the back cover of the Transmitter. product shall be destroyed. Never operate this product if it has a damaged cable or plug, if it is 2. Remove the used battery and load the new battery into the Transmitter. Please note the correct not working properly, if it has been dropped or damaged, or dropped into water. polarity. 3. Fix the 3 screws back to the back cover. WEEE Directive & Product Disposal At the end of its serviceable life, this product should not be treated as household or general waste. Storage It should be handed over to the applicable collection point for the recycling of electrical and It is important to keep fluid in the Fog Machine when storing for an extended period of time. This electronic equipment. will keep the seal and the parts lubricated. 1. Remove the tank lid. 2. Pour liquid into the tank. 3. Store on a flat, level surface to prevent liquid from spilling. Fuse Replacement If the Fog Machine does not work at all when it is connected to the power socket, then it is probably that the fuse has been broken. WARNING: Risk of electric shock and fire. Disconnect from power socket before replacing the fuse. 1. Turn the fuse knob counterclockwise to reveal the fuse. 2. Replace the fuse with the same size and type fuse: 5A, 125V 3. Place fuse in cover and reinstall by turning clockwise. Be sure not to over tighten. Cautions and Warnings ● Please read through this instructions manual before use. ● Before use, check the fog machine to see if there is any crack in the product cover, wired control cable and box, power cable and plug. Make sure there is not any exposed wired. Do not use if any of the above conditions is found. ● The fog machine will become hot during use. After use, please wait for some minutes before trying to touch it by hand. 4 5 6


Document Created: 2013-08-16 16:32:55
Document Modified: 2013-08-16 16:32:55
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC