Part 15B Test Report

FCC ID: 2AAV8QH-9826A

Test Report

Download: PDF
FCCID_2765171

FCC Test Report FCC ID:2AAV8QH-9826A Product： Main unit(receiver) Trade Name： QUHWA Model Name： QH-9826A Serial Model： N/A Report No.： NTEK-2015NT0813492F Prepared for SHENZHEN QIAOHUA INDUSTRIES LIMITED Qiaohua Industrial Zone, Luo Tian Forestry Center, Song Gang Town, Bao An District, Shenzhen, Guangdong, 518105 China Prepared by Shenzhen NTEK Testing Technology Co., Ltd. 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street, Bao’an District, Shenzhen P.R. China Tel.: +86-0755-61156588 Fax.: +86-0755-61156599 Website: www.ntek.org.cn

Page 2 of 19 Report No.: NTEK-2015NT0813492F TEST RESULT CERTIFICATION Applicant’s name ................. : SHENZHEN QIAOHUA INDUSTRIES LIMITED Address ................................. : Qiaohua Industrial Zone, Luo Tian Forestry Center, Song Gang Town, Bao An District, Shenzhen, Guangdong, 518105 China Manufacture's Name ............ : SHENZHEN QIAOHUA INDUSTRIES LIMITED Address ................................. : Qiaohua Industrial Zone, Luo Tian Forestry Center, Song Gang Town, Bao An District, Shenzhen, Guangdong, 518105 China Product description Product name ........................... : Main unit(receiver) Model and/or type reference : QH-9826A FCC Part15B:01 Oct.2014 Standards ............................. : ANSI C63.4:2014 This device described above has been tested by NTEK, and the test results show that the equipment under test (EUT) is in compliance with Part 15 of FCC Rules. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of NTEK, this document may be altered or revised by NTEK, personnel only, and shall be noted in the revision of the document. Date of Test ............................................ : Date (s) of performance of tests ............. : 13 Aug. 2015 ~25 Aug. 2015 Date of Issue ........................................... : 25 Aug. 2015 Test Result ............................................... : Pass Testing Engineer : (Allen Liu) Technical Manager : (Brown Lu) Authorized Signatory : (Sam Chen)

Page 3 of 19 Report No.: NTEK-2015NT0813492F Table of Contents Page 1 . TEST SUMMARY 4 1.1 TEST FACILITY 5 1.2 MEASUREMENT UNCERTAINTY 5 2 . GENERAL INFORMATION 6 2.1 GENERAL DESCRIPTION OF EUT 6 2.2 DESCRIPTION OF TEST SETUP 8 2.3 DESCRIPTION TEST PERIPHERAL AND EUT PERIPHERAL 9 2.4 MEASUREMENT INSTRUMENTS LIST 10 3 . EMC EMISSION TEST 11 3.1 CONDUCTED EMISSION MEASUREMENT 11 3.1.1 POWER LINE CONDUCTED EMISSION 11 3.1.2 TEST PROCEDURE 12 3.1.3 TEST SETUP 12 3.1.4 EUT OPERATING CONDITIONS 12 3.1.5 TEST RESULTS 13 3.2 RADIATED EMISSION MEASUREMENT 14 3.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT 14 3.2.2 TEST PROCEDURE 14 3.2.3 TEST SETUP 15 3.2.4 TEST RESULTS 16 3.2.5 TEST RESULTS(1000~12400MHz) 18 4 . EUT TEST PHOTO 19

Page 4 of 19 Report No.: NTEK-2015NT0813492F 1. TEST SUMMARY Test procedures according to the technical standards: EMC Emission Standard Test Item Limit Judgment Remark Conducted Emission Class B N/A FCC Part15B:2014 ANSI C63.4: 2014 Radiated Emission Class B PASS NOTE: (1) ’N/A’ denotes test is not applicable in this Test Report (2) For client’s request and manual description, the test will not be executed.

Page 5 of 19 Report No.: NTEK-2015NT0813492F 1.1 TEST FACILITY NTEK Testing Technology Co., Ltd Add. : 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street, Bao’an District, Shenzhen P.R. China. FCC Registration Number:238937; IC Registration Number:9270A-1 CNAS Registration Number:L5516 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %. A. Conducted Measurement : Test Site Method Measurement Frequency Range U，(dB) NOTE NTEKC01 ANSI 150 KHz ~ 30MHz 3.2 B. Radiated Measurement : Test Site Method Measurement Frequency Range U，(dB) NOTE NTEKA01 ANSI 30MHz ~ 1000MHz 4.7 1GHz ~12.4GHz 5.0

Page 6 of 19 Report No.: NTEK-2015NT0813492F 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Equipment Main unit(receiver) Model Name QH-9826A Additional Model N/A Number(s) Model Difference N/A The EUT is a Main unit(receiver) . Product Description Operation Frequency: 433.92MHz Modulation Type: ASK Power Source DC Voltage Adapter N/A Battery 1.5V*3 cell ”AAA” alkaline battery

Page 7 of 19 Report No.: NTEK-2015NT0813492F 2.1.1 DESCRIPTION OF TEST MODES To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mentioned above was evaluated respectively. Pretest Mode Description Mode 1 normal working Mode For Radiated Test Final Test Mode Description Mode 1 normal working Mode Note: Final Test Mode: Through Pre-scan, find the mode 1 is the worse case. Only the worst case mode is recorded in the report.

Page 8 of 19 Report No.: NTEK-2015NT0813492F 2.2 DESCRIPTION OF TEST SETUP E-1 EUT

Page 9 of 19 Report No.: NTEK-2015NT0813492F 2.3 DESCRIPTION TEST PERIPHERAL AND EUT PERIPHERAL The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Item Equipment Brand Model/Type No. Series No. Note E-1 Main unit(receiver) QUHWA QH-9826A N/A EUT Item Shielded Type Ferrite Core Length Note Note: (1) The support equipment was authorized by Declaration of Confirmation. (2) For detachable type I/O cable should be specified the length in cm in『Length』column. (3) “YES” means “shielded” “with core”; “NO” means “unshielded” “without core”.

Page 10 of 19 Report No.: NTEK-2015NT0813492F 2.4 MEASUREMENT INSTRUMENTS LIST 2.4.1 CONDUCTED TEST SITE Calibra Kind of Item Manufacturer Type No. Serial No. Last calibration Calibrated until tion Equipment period 1 LISN R&S ENV216 101313 Jul. 06, 2015 Jul. 05, 2016 1 year SCHWARZBE 2 LISN NNLK 8129 8129245 Dec. 25, 2014 Dec. 24, 2015 1 year CK Pulse SCHWARZBE 3 VTSD 9561F 9716 Dec. 25, 2014 Dec. 24, 2015 1 year Limiter CK ANRITSU 4 50Ω Switch MP59B 6200983704 Jul. 06, 2015 Jul. 05, 2016 1 year CORP 5 Test Cable N/A C01 N/A Jul. 06, 2015 Jul. 05, 2016 1 year 6 Test Cable N/A C02 N/A Jul. 06, 2015 Jul. 05, 2016 1 year 7 Test Cable N/A C03 N/A Jul. 06, 2015 Jul. 05, 2016 1 year EMI Test 8 R&S ESCI 101160 Jul. 06, 2015 Jul. 05, 2016 1 year Receiver Passive 9 Voltage ESH2-Z3 R&S 100196 Jul. 06, 2015 Jul. 05, 2016 1 year Probe Absorbing 10 R&S MDS-21 100423 Jul. 08, 2015 Jul. 07, 2016 1 year Clamp 2.4.2 RADIATED TEST SITE Calibra Kind of Item Manufacturer Type No. Serial No. Last calibration Calibrated until tion Equipment period Bilog 1 TESEQ CBL6111D 31216 Jul. 06, 2015 Jul. 05, 2016 1 year Antenna 2 Test Cable N/A R-01 N/A Dec. 25, 2014 Dec. 24, 2015 1 year 3 Test Cable N/A R-02 N/A Dec. 25, 2014 Dec. 24, 2015 1 year EMI Test 4 R&S ESCI-7 101318 Jul. 06, 2015 Jul. 05, 2016 1 year Receiver Antenna 5 EM SC100_1 N/A N/A N/A N/A Mast 6 Turn Table EM SC100 060531 N/A N/A N/A 7 50Ω Switch Anritsu Corp MP59B 6200983705 Jul. 06, 2015 Jul. 05, 2016 1 year Spectrum 8 Aglient E4407B MY45108040 Jul. 06, 2015 Jul. 05, 2016 1 year Analyzer Horn 9 EM EM-AH-10180 2011071402 Jul. 06, 2015 Jul. 05, 2016 1 year Antenna 10 Amplifier EM EM-30180 060538 Jul. 06, 2015 Jul. 05, 2016 1 year Loop 11 ARA PLA-1030/B 1029 Jul. 06, 2015 Jul. 05, 2016 1 year Antenna

Page 11 of 19 Report No.: NTEK-2015NT0813492F 3. EMC EMISSION TEST 3.1 CONDUCTED EMISSION MEASUREMENT 3.1.1 POWER LINE CONDUCTED EMISSION (Frequency Range 150KHz-30MHz) Class A (dBuV) Class B (dBuV) FREQUENCY (MHz) Quasi-peak Average Quasi-peak Average 0.15 -0.5 79.00 66.00 66 - 56 * 56 - 46 * 0.50 -5.0 73.00 60.00 56.00 46.00 5.0 -30.0 73.00 60.00 60.00 50.00 Note: (1) The tighter limit applies at the band edges. (2) The limit of " * " marked band means the limitation decreases linearly with the logarithm of the frequency in the range. The following table is the setting of the receiver Receiver Parameters Setting Attenuation 10 dB Start Frequency 0.15 MHz Stop Frequency 30 MHz IF Bandwidth 9 kHz

Page 12 of 19 Report No.: NTEK-2015NT0813492F 3.1.2 TEST PROCEDURE a. The EUT was placed 0.8 meters from the horizontal ground plane with EUT being connected to the power mains through a line impedance stabilization network (LISN). All other support equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. b. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 to 40 cm long. c. I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m. d. LISN at least 80 cm from nearest part of EUT chassis. e. For the actual test configuration, please refer to the related Item –EUT Test Photos. 3.1.3 TEST SETUP 3.1.4 EUT OPERATING CONDITIONS The EUT tested system was configured as the statements of 2.3 Unless otherwise a special operating condition is specified in the follows during the testing.

Page 13 of 19 Report No.: NTEK-2015NT0813492F 3.1.5 TEST RESULTS EUT： Main unit(receiver) Model Name. ： QH-9826A Temperature： 26 ℃ Relative Humidity： 54% Pressure： 1010hPa Test Date : N/A Test Mode： N/A Phase : N/A Test Voltage ： N/A

Page 14 of 19 Report No.: NTEK-2015NT0813492F 3.2 RADIATED EMISSION MEASUREMENT 3.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT Class A (at 10m) Class B (at 3m) FREQUENCY (MHz) dBuV/m dBuV/m 30 ~ 88 39.0 40.0 88 ~ 216 43.5 43.5 216 ~ 960 46.5 46.0 Above 960 49.5 54.0 Notes: (1) The limit for radiated test was performed according to as following: FCC PART 15B /ICES-003. (2) The tighter limit applies at the band edges. (3) Emission level (dBuV/m)=20log Emission level (uV/m). 3.2.2 TEST PROCEDURE Test Arrangement for Radiated Emissions up to 1 GHz a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at an accredited test facility. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. Note: The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for quasi-peak detection (QP) at frequency below 1GHz. Test Arrangement for Radiated Emissions above 1 GHz. a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at an accredited chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna can be varied from one meter to four meters, the height of adjustment depends on the EUT height and the antenna 3dB beamwidth both, to detect the maximum value of the field strength.Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading.

Page 15 of 19 Report No.: NTEK-2015NT0813492F Note：For the hand-held device, the EUT should be measured for all 3 axes and only the worst case is recorded in the report During the radiated emission test, the Spectrum Analyzer was set with the following configurations: Frequency Band Function Resolution bandwidth Video Bandwidth (MHz) 30 to 1000 QP 120 kHz 300 kHz Peak 1 MHz 1 MHz Above 1000 Peak 1 MHz 10 Hz 3.2.3 TEST SETUP For Radiated Emission 30~1000MHz (B) Radiated Emission Test Set-Up Frequency Above 1GHz

Page 16 of 19 Report No.: NTEK-2015NT0813492F 3.2.4 TEST RESULTS TEST RESULTS (30~1000 MHz) EUT： Main unit(receiver) Model Name ： QH-9826A Temperature： 24 ℃ Relative Humidity： 54% Pressure： 1010 hPa Test Date : 2015-08-18 Test Mode ： Mode 1 Polarization : Horizontal Test Power ： DC 4.5V Freq. Reading Factor Measurement Limit Over Remark (MHz) (dBuV) (dBuV) (dBuV) (dBuV) (dB) 32.2924 5.10 18.66 23.76 40.00 -16.24 QP 66.266 7.44 6.58 14.02 40.00 -25.98 QP 95.427 5.45 10.12 15.57 43.50 -27.93 QP 152.1297 6.19 11.77 17.96 43.50 -25.54 QP 332.5187 6.32 13.72 20.04 46.00 -25.96 QP 435.5898 7.83 15.35 23.18 46.00 -22.82 QP Remark: Factor = Antenna Factor + Cable Loss - Amplifier.

Page 17 of 19 Report No.: NTEK-2015NT0813492F EUT： Main unit(receiver) Model Name ： QH-9826A Temperature： 24 ℃ Relative Humidity： 54% Pressure： 1010 hPa Test Date : 2015-08-18 Test Mode ： Mode 1 Polarization : Vertical Test Power ： DC 4.5V Freq. Reading Factor Measurement Limit Over Remark (MHz) (dBuV) (dBuV) (dBuV) (dBuV) (dB) 31.6202 6.89 18.99 25.88 40.00 -14.12 QP 66.4989 9.03 6.79 15.82 40.00 -24.18 QP 101.2883 6.74 10.26 17.00 43.50 -26.50 QP 162.0414 9.04 11.56 20.60 43.50 -22.90 QP 434.0649 8.21 15.21 23.42 46.00 -22.58 QP 734.4913 8.05 21.88 29.93 46.00 -16.07 QP Remark: Factor = Antenna Factor + Cable Loss - Amplifier.

Page 18 of 19 Report No.: NTEK-2015NT0813492F 3.2.5 TEST RESULTS(1000~12400MHz) Emission Frequency Meter Reading Factor Limits Margin Polar Level Remark (H/V) (MHz) (dBm) (dB) (dBm) (dBm) (dB) V 1340.332 58.84 -12.78 46.06 74.00 -27.94 peak V 1340.332 46.36 -12.78 33.58 54.00 -20.42 AVG V 1587.100 62.11 -11.97 50.14 74.00 -23.86 peak V 1587.100 52.99 -11.97 41.02 54.00 -12.98 AVG V 2123.821 59.72 -8.28 51.44 74.00 -22.56 peak V 2123.821 48.86 -8.28 40.58 54.00 -13.42 AVG H 1197.525 62.77 -12.45 50.32 74.00 -23.68 peak H 1197.525 52.47 -12.45 40.02 54.00 -13.98 AVG H 1796.491 61.58 -10.87 50.71 74.00 -23.29 peak H 1796.491 50.12 -10.87 39.25 54.00 -14.75 AVG H 2427.350 56.05 -9.17 46.88 74.00 -27.12 peak H 2427.350 44.53 -9.17 35.36 54.00 -18.64 AVG Remark: Absolute Level= ReadingLevel+ Factor, Margin= Absolute Level - Limit

Page 19 of 19 Report No.: NTEK-2015NT0813492F 4. EUT TEST PHOTO Radiated Measurement Photos


Document Created: 2015-09-25 15:07:53
Document Modified: 2015-09-25 15:07:53
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC