User manual

FCC ID: 2AATL-FNCC2541

Users Manual

Download: PDF
FCCID_2372932

FN-LINK TECHNOLOGY LIMITED Bluetooth Low Energy (BLE) Module FN-CC2541 User Manual / User Guide http://www.fn-link.com Page 1/8

FN-LINK TECHNOLOGY LIMITED 1. Introduction FN-CC2541 is 2.4GHz Bluetooth low power system on chip (SoC), support 250kbps, 500kbps, 1Mbps and 2Mbps data rate, with connecting budget excellent, but the front end the application, receiving 1Mbps with a sensitivity of -94dBm, mainly used in the 2.4GHz Bluetooth low energy system, personal 2.4GHz system, man-machine interface such as a keyboard, mouse, and remote control etc., sports and leisure equipment, mobile phone accessories and consumer electronics. 1.1 Overview The block diagram for the module is shown in Figure 1. The modules can be roughly divided into one of three categories: CPU-related modules; modules related to power, test, and clock distribution; and radio-related modules. http://www.fn-link.com Page 2/8

rwLNicreckNo.coy umrrep 12 sortwane rearures Sample Applcations and Profles Genenc Applcaions for GAP Central and Perperal Rales Prosimy, Accelerometer, Simple keys, and Batery GATT Senices More Agplcations Supparted n BLE Sottware Stack Mubiple Contiquration Options Singe—chip configuraton, alowing applcations t run on ©2541 Nemwork processor nterface for agplcations running on an extermal mcrocortroller BTookWindows PC application for evaluation, development, and test 13 appuicaions 2.4GHiz Bluetooth low energy systems Propitary 2.4GHz systems Humar—inteface devices (Keyboard. Mouse, Remote Contro) Sports and leisure equipment Moile Phone accessories Consurmer etecctronics 2. Mechantcal Specification 2.1 Oullne Drawing Pssn

FN-LINK TECHNOLOGY LIMITED 2.2 Connector Pin Definition Pin # Name Description 1 VCC 2-3.6V 2 VCC 2-3.6V 3 NC NOP 4 NC NOP 5 NC NOP 6 P2-2 7 P2-0 8 P2-1 9 GND USBDP-SCL 10 GND USBDM-SDA 11 GND USBVDD 12 GND GND 13 P1-6 http://www.fn-link.com Page 4/8

FN-LINK TECHNOLOGY LIMITED 14 P1-7 15 P1-5 16 NC NOP 17 P1-1 18 P1-0 19 GND GND 20 P0-7 21 P0-6 22 P0-5 23 P0-4 24 P0-3 25 P0-2 26 P0-1 27 P0-0 28 RST RESET 29 GND GND 30 GND GND 31 GND J2 32 TX/RX RF TX/RX 33 GND GND http://www.fn-link.com Page 5/8

e—Link Techno.ooy LimeD 2.3 Layout reference 3. Anterina Specification Antenna plate FPC antenna Antenna gain coBi Frequency range 240H7—2 400047 rower 0dBm Comnectortype Fixed antenna company name hu Heck itp:iwwactrelink.com Paess

FN-LINK TECHNOLOGY LIMITED 4. Antenna Installation Guide 4.1 Check FN-CC2541 Module connection pin is clean for soldering. 4.2 Place the Module on the Master PCB. Then solder it. 4.3 After soldering, Check all pads are well connected. http://www.fn-link.com Page 7/8

erLNK Tecinorooy Limimeo 5. Package 5.1 blister puckaging A piece of 50 PGS ($00 pos/bag) Mipstwinetndink.com Prgecs

FCC Statement: The final end product must be labeled in a visible area with the following "Contains TX FCC ID:2AATL-FNCC2541". If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 stayement is required to be availale in the users manual: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Radiation Exposure Statement: This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. This device is intended only for OEM integrators under the following conditions: 1)This module is granted as a Single Modular Approval. 2)This device has been designed to operate with a FPC antenna having a maximum gain of 0dBi.Only this type of antenna may be used.


Document Created: 2014-08-21 11:33:38
Document Modified: 2014-08-21 11:33:38
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC