14_AW-QDR-CELL TestRpt

FCC ID: 2AANZQDRCELL

Test Report

Download: PDF
FCCID_3191053

Page 1 of 31 FCC Test Report Report No.: AGC04900161002FE03 FCC ID : 2AANZQDRCELL APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Remote Control BRAND NAME : N/A MODEL NAME : AW-QDR-CELL CLIENT : DGL Group LTD. DATE OF ISSUE : Nov. 05, 2016 STANDARD(S) : FCC Part 15 Rules TEST PROCEDURE(S) : REPORT VERSION V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd CAUTION: This report shall not be reproduced except in full without the written permission of the test laboratory and shall not be quoted out of context.

Report No.: AGC04900161002FE03 Page 2 of 31 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Nov. 05, 2016 Valid Original Report

Report No.: AGC04900161002FE03 Page 3 of 31 TABLE OF CONTENTS 1. VERIFICATION OF CONFORMITY .............................................................................................................. 4 2. GENERAL INFORMATION ........................................................................................................................... 5 2.1. PRODUCT DESCRIPTION ................................................................................................................... 5 2.2. TABLE OF CARRIER FREQUENCY ..................................................................................................... 5 3. MEASUREMENT UNCERTAINTY................................................................................................................ 5 4. DESCRIPTION OF TEST MODES................................................................................................................ 6 5. SYSTEM TEST CONFIGURATION .............................................................................................................. 7 5.1. CONFIGURATION OF EUT SYSTEM ................................................................................................... 7 5.2. EQUIPMENT USED IN EUT SYSTEM .................................................................................................. 7 5.3. SUMMARY OF TEST RESULTS ........................................................................................................... 7 6. TEST FACILITY............................................................................................................................................. 8 7. RADIATED EMISSION.................................................................................................................................. 9 7.1TEST LIMIT .............................................................................................................................................. 9 7.2. MEASUREMENT PROCEDURE ......................................................................................................... 10 7.3. TEST SETUP ....................................................................................................................................... 12 7.4. TEST RESULT ..................................................................................................................................... 13 8. BAND EDGE EMISSION............................................................................................................................. 18 8.1. MEASUREMENT PROCEDURE ......................................................................................................... 18 8.2 TEST SETUP ........................................................................................................................................ 18 8.3 RADIATED TEST RESULT ................................................................................................................... 18 9. 20DB BANDWIDTH .................................................................................................................................... 23 9.1. MEASUREMENT PROCEDURE ......................................................................................................... 23 9.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ............................................................... 23 9.3. MEASUREMENT RESULTS ............................................................................................................... 23 APPENDIX A: PHOTOGRAPHS OF TEST SETUP ....................................................................................... 26 APPENDIX B: PHOTOGRAPHS OF EUT ...................................................................................................... 27

Report No.: AGC04900161002FE03 Page 4 of 31 1. VERIFICATION OF CONFORMITY Applicant DGL Group LTD. Address 195 Raritan Center Parkway Edison, New Jersey United States 08837 Manufacturer DGL Group LTD. Address 195 Raritan Center Parkway Edison, New Jersey United States 08837 Product Designation Remote Control Brand Name N/A Test Model AW-QDR-CELL Date of test Oct.20, 2016 to Oct. 21, 2016 Deviation None Condition of Test Sample Normal Test Result Pass Report Template AGCRT-US-BR/RF We hereby certify that: The above equipment was tested by Dongguan Precise Testing Service Co., Ltd. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10 (2013) and the energy emitted by the sample EUT tested as described in this report is in compliance with radiated emission limits of FCC Rules Part 15.249. Tested by Max Zhang(Zhang Yi) Nov. 05, 2016 Reviewed by Bart Xie(Xie Xiaobin)) Nov. 05, 2016 Approved by Solger Zhang(Zhang Hongyi) Nov. 05, 2016 Authorized Officer

Report No.: AGC04900161002FE03 Page 5 of 31 2. GENERAL INFORMATION 2.1. PRODUCT DESCRIPTION A major technical description of EUT is described as following Operation Frequency 2.405 GHz to 2.475GHz Maximum field strength 86.13dBuV/m@3m(AV) Modulation GFSK Number of channels 71 Antenna Gain 3dBi Antenna Designation Wire Antenna (Met 15.203 Antenna requirement) Hardware Version HY-851TX-LG Software Version V1.0 Power Supply DC 6V by battery 2.2. TABLE OF CARRIER FREQUENCY Frequency Band Channel Number Frequency 1 2405MHZ 2 2406MHZ … … 2400~2483.5MHZ … … 70 2474MHZ 71 2475MHZ Note: The channel spacing is 1MHz.

Report No.: AGC04900161002FE03 Page 6 of 31 3. MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ±U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 Conducted Emission Test ±3.18dB 2 All emissions,radiated ±3.91dB 3 Temperature ±0.5°C 4 Humidity ±2% 4. DESCRIPTION OF TEST MODES NO. TEST MODE DESCRIPTION 1 Low channel TX in GFSK modulation 2 Middle channel TX in GFSK modulation 3 High channel TX in GFSK modulation Note: 1. All the test modes can be supply by battery, only the result of the worst case was recorded in the report, if no other cases. 2. For Radiated Emission, 3axis were chosen for testing for each applicable mode.

Report No.: AGC04900161002FE03 Page 7 of 31 5. SYSTEM TEST CONFIGURATION 5.1. CONFIGURATION OF EUT SYSTEM Configure 1: EUT 5.2. EQUIPMENT USED IN EUT SYSTEM Item Equipment Model No. ID or Specification Remark 1 Remote Control AW-QDR-CELL 2AANZQDRCELL EUT 5.3. SUMMARY OF TEST RESULTS FCC RULES DESCRIPTION OF TEST RESULT §15.249 Radiated Emission Compliant §15.249 Band Edges Compliant §15.215 20dB bandwidth Compliant

Report No.: AGC04900161002FE03 Page 8 of 31 6. TEST FACILITY Site Dongguan Precise Testing Service Co., Ltd. Building D, Baoding Technology Park,Guangming Road2, Dongcheng District, Location Dongguan, Guangdong, China. FCC Registration No. 371540 The test site is constructed and calibrated to meet the FCC requirements in Description documents ANSI C63.4:2014. ALL TEST EQUIPMENT LIST Radiated Emission Test Site Model Serial Last Due Name of Equipment Manufacturer Number Number Calibration Calibration Rohde & EMI Test Receiver ESCI 101417 July 3, 2016 July 2, 2017 Schwarz Trilog Broadband Antenna SCHWARZBECK VULB9160 9160-3355 July 3, 2016 July 2, 2017 (25M-1GHz) Signal Amplifier SCHWARZBECK BBV 9475 9745-0013 July 3, 2016 July 2, 2017 RF Cable SCHWARZBECK AK9515E 96221 July 3, 2016 July 2, 2017 3m Anechoic Chamber CHENGYU 966 PTS-001 June 3, 2016 June 2, 2017 MULTI-DEVICE Positioning Max-Full MF-7802 MF780208339 N/A N/A Controller Active loop antenna Schwarzbeck FMZB1519 1519-038 June 3, 2016 June 2, 2017 (9K-30MHz) Spectrum analyzer Agilent E4407B MY46185649 June 3, 2016 June 2, 2017 Horn Antenna (1G-18GHz) SCHWARZBECK BBHA9120D 9120D-1246 June 3, 2016 June 2, 2017 Horn Ant (18G-40GHz) Schwarzbeck BBHA 9170 9170-181 June 3, 2016 June 2, 2017

Report No.: AGC04900161002FE03 Page 9 of 31 7. RADIATED EMISSION 7.1TEST LIMIT Standard FCC15.249 Fundamental Frequency Field Strength of Fundamental Field Strength of Harmonics (millivolts/meter) (microvolts/meter) 900-928MHz 50 500 2400-2483.5MHz 50 500 5725-5875MHz 50 500 24.0-24.25GHz 250 2500 Standard FCC 15.209 Frequency Distance Field Strengths Limit (MHz) Meters μ V/m dB(μV)/m 0.009 ~ 0.490 300 2400/F(kHz) --- 0.490 ~ 1.705 30 24000/F(kHz) --- 1.705 ~ 30 30 30 --- 30 ~ 88 3 100 40.0 88 ~ 216 3 150 43.5 216 ~ 960 3 200 46.0 960 ~ 1000 3 500 54.0 Above 1000 3 Other:74.0 dB(μV)/m (Peak) 54.0 dB(μV)/m (Average) Remark： (1) Emission level dBμ V = 20 log Emission level μ V/m (2) The smaller limit shall apply at the cross point between two frequency bands. (3) Distance is the distance in meters between the measuring instrument, antenna and the closest point of any part of the device or system.

Report No.: AGC04900161002FE03 Page 10 of 31 7.2. MEASUREMENT PROCEDURE 1. The EUT was placed on the top of the turntable 0.8 or 1.5 meter above ground. The phase center of the receiving antenna mounted on the top of a height-variable antenna tower was placed 3 meters far away from the turntable. 2. Power on the EUT and all the supporting units. The turntable was rotated by 360 degrees to determine the position of the highest radiation. 3. The height of the broadband receiving antenna was varied between one meter and four meters above ground to find the maximum emissions field strength of both horizontal and vertical polarization. 4. For each suspected emissions, the antenna tower was scan (from 1 M to 4 M) and then the turntable was rotated (from 0 degree to 360 degrees) to find the maximum reading. 5. Set the test-receiver system to Peak or CISPR quasi-peak Detect Function with specified bandwidth under Maximum Hold Mode. 6. For emissions above 1GHz, use 1MHz VBW and RBW for peak reading. Then 1MHz RBW and 10Hz VBW for average reading in spectrum analyzer. Place the measurement antenna away from each area of the EUT determined to be a source of emissions at the specified measurement distance, while keeping the measurement antenna aimed at the source of emissions at each frequency of significant emissions, with polarization oriented for maximum response. The measurement antenna may have to be higher or lower than the EUT, depending on the radiation pattern of the emission and staying aimed at the emission source for receiving the maximum signal. The final measurement antenna elevation shall be that which maximizes the emissions. The measurement antenna elevation for maximum emissions shall be restricted to a range of heights of from 1 m to 4 m above the ground or reference ground plane. 7. When the radiated emissions limits are expressed in terms of the average value of the emissions, and pulsed operation is employed, the measurement field strength shall be determined by averaging over one complete pulse train, including blanking intervals, as long as the pulse train does not exceed 0.1 seconds. As an alternative (provided the transmitter operates for longer than 0.1 seconds) or in cases where the pulse train exceeds 0.1 seconds, the measured field strength shall be determined from the average absolute voltage during a 0.1 second interval during which the field strength is at its maximum values. 8.If the emissions level of the EUT in peak mode was 3 dB lower than the average limit specified, then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions which do not have 3 dB margin will be repeated one by one using the quasi-peak method for below 1GHz. 9. For testing above 1GHz, the emissions level of the EUT in peak mode was lower than average limit (that means the emissions level in peak mode also complies with the limit in average mode), then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions will be measured in average mode again and reported. 10. In case the emission is lower than 30MHz, loop antenna has to be used for measurement and the recorded data should be QP measured by receiver. High - Low scan is not required in this case.

Report No.: AGC04900161002FE03 Page 11 of 31 The following table is the setting of spectrum analyzer and receiver. Spectrum Parameter Setting Start ~Stop Frequency 9KHz~150KHz/RB 200Hz for QP Start ~Stop Frequency 150KHz~30MHz/RB 9KHz for QP Start ~Stop Frequency 30MHz~1000MHz/RB 120KHz for QP 1GHz~26.5GHz Start ~Stop Frequency 1MHz/1MHz for Peak, 1MHz/10Hz for Average Receiver Parameter Setting Start ~Stop Frequency 9KHz~150KHz/RB 200Hz for QP Start ~Stop Frequency 150KHz~30MHz/RB 9KHz for QP Start ~Stop Frequency 30MHz~1000MHz/RB 120KHz for QP

Report No.: AGC04900161002FE03 Page 12 of 31 7.3. TEST SETUP Radiated Emission Test-Setup Frequency Below 30MHz RADIATED EMISSION TEST SETUP 30MHz-1000MHz RADIATED EMISSION TEST SETUP ABOVE 1000MHz

Report No.: AGC04900161002FE03 Page 13 of 31 7.4. TEST RESULT RADIATED EMISSION BELOW 30MHZ No emission found between lowest internal used/generated frequencies to 30MHz. RADIATED EMISSION 30MHz- 1GHZ EUT： Remote Control Model Name. ： AW-QDR-CELL Temperature： 20 ℃ Relative Humidtity： 48% Pressure： 1010 hPa Test Voltage ： DC6V Test Mode ： Mode 1 Polarization : Horizontal RESULT: PASS

Report No.: AGC04900161002FE03 Page 14 of 31 EUT： Remote Control Model Name. ： AW-QDR-CELL Temperature： 20 ℃ Relative Humidtity： 48% Pressure： 1010 hPa Test Voltage ： DC6V Test Mode ： Mode 1 Polarization : Vertical RESULT: PASS Note: Factor=Antenna Factor + Cable loss, Margin=Result-Limit. The “Factor” value can be calculated automatically by software of measurement system. The mode 1 is the worst case, and only the data of the worst case recorded in this test report.

Report No.: AGC04900161002FE03 Page 15 of 31 RADIATED EMISSION ABOVE 1GHZ EUT： Remote Control Model Name. ： AW-QDR-CELL Temperature： 20 ℃ Relative Humidtity： 48% Pressure： 1010 hPa Test Voltage ： DC6V Test Mode ： Mode 1 Polarization : Horizontal Frequency Meter Reading Factor Emission Level Limits Margin Value Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 2405.013 100.15 -9.37 90.78 114 -23.22 peak 2405.013 95.12 -9.37 85.75 94 -8.25 AVG 4810.026 48.38 3.74 52.12 74 -21.88 peak 4810.026 43.21 3.74 46.95 54 -7.05 AVG 7215.039 41.87 8.14 50.01 74 -23.99 peak 7215.039 36.74 8.14 44.88 54 -9.12 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. EUT： Remote Control Model Name. ： AW-QDR-CELL Temperature： 20 ℃ Relative Humidtity： 48% Pressure： 1010 hPa Test Voltage ： DC6V Test Mode ： Mode 1 Polarization : Vertical Frequency Meter Reading Factor Emission Level Limits Margin Value Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 2405.013 98.07 -9.37 88.7 114 -25.3 peak 2405.013 93.11 -9.37 83.74 94 -10.26 AVG 4810.026 47.28 3.74 51.02 74 -22.98 peak 4810.026 42.54 3.74 46.28 54 -7.72 AVG 7215.039 41.67 8.14 49.81 74 -24.19 peak 7215.039 36.53 8.14 44.67 54 -9.33 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier.

Report No.: AGC04900161002FE03 Page 16 of 31 EUT： Remote Control Model Name. ： AW-QDR-CELL Temperature： 20 ℃ Relative Humidtity： 48% Pressure： 1010 hPa Test Voltage ： DC6V Test Mode ： Mode 2 Polarization : Horizontal Frequency Meter Reading Factor Emission Level Limits Margin Value Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 2445.016 99.67 -9.63 90.04 114 -23.96 peak 2445.016 94.31 -9.63 84.68 94 -9.32 AVG 4890.032 48.96 3.76 52.72 74 -21.28 peak 4890.032 43.75 3.76 47.51 54 -6.49 AVG 7335.048 43.22 8.17 51.39 74 -22.61 peak 7335.048 38.09 8.17 46.26 54 -7.74 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. EUT： Remote Control Model Name. ： AW-QDR-CELL Temperature： 20 ℃ Relative Humidtity： 48% Pressure： 1010 hPa Test Voltage ： DC6V Test Mode ： Mode 2 Polarization : Vertical Frequency Meter Reading Factor Emission Level Limits Margin Value Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 2445.016 97.38 -9.63 87.75 114 -26.25 peak 2445.016 92.15 -9.63 82.52 94 -11.48 AVG 4890.032 47.94 3.76 51.7 74 -22.3 peak 4890.032 42.59 3.76 46.35 54 -7.65 AVG 7335.048 42.38 8.17 50.55 74 -23.45 peak 7335.048 36.95 8.17 45.12 54 -8.88 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier.

Report No.: AGC04900161002FE03 Page 17 of 31 EUT： Remote Control Model Name. ： AW-QDR-CELL Temperature： 20 ℃ Relative Humidtity： 48% Pressure： 1010 hPa Test Voltage ： DC6V Test Mode ： Mode 3 Polarization : Horizontal Frequency Meter Reading Factor Emission Level Limits Margin Value Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 2475.021 101.18 -9.61 91.57 114 -22.43 peak 2475.021 95.74 -9.61 86.13 94 -7.87 AVG 4950.042 53.22 3.83 57.05 74 -16.95 peak 4950.042 47.95 3.83 51.78 54 -2.22 AVG 7425.063 41.85 8.21 50.06 74 -23.94 peak 7425.063 36.74 8.21 44.95 54 -9.05 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. EUT： Remote Control Model Name. ： AW-QDR-CELL Temperature： 20 ℃ Relative Humidtity： 48% Pressure： 1010 hPa Test Voltage ： DC6V Test Mode ： Mode 3 Polarization : Vertical Frequency Meter Reading Factor Emission Level Limits Margin Value Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 2475.021 99.04 -9.61 89.43 114 -24.57 peak 2475.021 93.58 -9.61 83.97 94 -10.03 AVG 4950.042 51.76 3.83 55.59 74 -18.41 peak 4950.042 46.28 3.83 50.11 54 -3.89 AVG 7425.063 42.12 8.21 50.33 74 -23.67 peak 7425.063 37.18 8.21 45.39 54 -8.61 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Note: Other emissions from 8G to 25 GHz are considered as ambient noise. No recording in the test report. Factor=Antenna Factor + Cable loss - Amplifier gain, Margin=Measurement-Limit. The “Factor” value can be calculated automatically by software of measurement system.

Report No.: AGC04900161002FE03 Page 18 of 31 8. BAND EDGE EMISSION 8.1. MEASUREMENT PROCEDURE 1. The lowest or highest channels are tested to verify the largest transmission and spurious emissions power at the continuous transmission mode. 2. Max hold the trace of the setp 1,and the EUT operates at hopping-on test mode to verify the largest spurious emissions power. 3. Set the spectrum analyzer in the following setting in order to capture the lower and upper band-edges of the emission: (a) PEAK: RBW=VBW=1MHz / Sweep=AUTO (b) AVERAGE: RBW=1MHz ; VBW=1/on time(1KHz) / Sweep=AUTO 8.2 TEST SETUP RADIATED EMISSION TEST SETUP 8.3 RADIATED TEST RESULT Note: 1. Factor=Antenna Factor + Cable loss - Amplifier gain. Field Strength=Factor + Reading level 2. The factor had been edited in the “Input Correction” of the Spectrum Analyzer. So the Amplitude of test plots is equal to Reading level plus the Factor in dB. Use the A dB(μV) to represent the Amplitude. Use the F dB(μV/m) to represent the Field Strength. So A=F.

Report No.: AGC04900161002FE03 Page 19 of 31 EUT： Remote Control Model Name. ： AW-QDR-CELL Temperature： 20 ℃ Relative Humidtity： 48% Pressure： 1010 hPa Test Voltage ： DC6V Test Mode ： Mode 1 Polarization : Horizontal PK Value AV Value

Report No.: AGC04900161002FE03 Page 20 of 31 EUT： Remote Control Model Name. ： AW-QDR-CELL Temperature： 20 ℃ Relative Humidtity： 48% Pressure： 1010 hPa Test Voltage ： DC6V Test Mode ： Mode 1 Polarization : Vertical PK Value AV Value

Report No.: AGC04900161002FE03 Page 21 of 31 EUT： Remote Control Model Name. ： AW-QDR-CELL Temperature： 20 ℃ Relative Humidtity： 48% Pressure： 1010 hPa Test Voltage ： DC6V Test Mode ： Mode 3 Polarization : Horizontal PK Value AV Value

Report No.: AGC04900161002FE03 Page 22 of 31 EUT： Remote Control Model Name. ： AW-QDR-CELL Temperature： 20 ℃ Relative Humidtity： 48% Pressure： 1010 hPa Test Voltage ： DC6V Test Mode ： Mode 3 Polarization : Vertical PK Value AV Value Note: Factor=Antenna Factor + Cable loss - Amplifier gain, Over=Measure-Limit. The “Factor” value can be calculated automatically by software of measurement system.

Report No.: AGC04900161002FE03 Page 23 of 31 9. 20DB BANDWIDTH 9.1. MEASUREMENT PROCEDURE 1. The spectrum analyzer center frequency is set to the nominal EUT channel center frequency. The span range for the EMI receiver or spectrum analyzer shall be between two times and five times the OBW. 2. The nominal IF filter bandwidth (3 dB RBW) shall be in the range of 1% to 5% of the OBW and video bandwidth (VBW) shall be approximately three times RBW, unless otherwise specified by the applicable requirement. 3. Set the reference level of the instrument as required, keeping the signal from exceeding the maximum input mixer level for linear operation. In general, the peak of the spectral envelope shall be more than [10 log (OBW/RBW)] below the reference level. 4. Set SPA Trace 1 Max hold, then View. 9.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) 9.3. MEASUREMENT RESULTS TEST ITEM 20DB BANDWIDTH TEST MODE Mode1;Mode2;Mode3 Test Data (MHz) Criteria Low Channel 5.723 PASS Middle Channel 5.445 PASS High Channel 4.349 PASS

Report No.: AGC04900161002FE03 Page 24 of 31 TEST PLOT OF BANDWIDTH FOR LOW CHANNEL TEST PLOT OF BANDWIDTH FOR MIDDLE CHANNEL

Report No.: AGC04900161002FE03 Page 25 of 31 TEST PLOT OF BANDWIDTH FOR HIGH CHANNEL

Report No.: AGC04900161002FE03 Page 26 of 31 APPENDIX A: PHOTOGRAPHS OF TEST SETUP RADIATED EMISSION TEST SETUP BELOW 1GHz RADIATED EMISSION TEST SETUP ABOVE 1GHz

Report No.: AGC04900161002FE03 Page 27 of 31 APPENDIX B: PHOTOGRAPHS OF EUT TOTAL VIEW OF EUT TOP VIEW OF EUT

Report No.: AGC04900161002FE03 Page 28 of 31 BOTTOM VIEW OF EUT FRONT VIEW OF EUT

Report No.: AGC04900161002FE03 Page 29 of 31 BACK VIEW OF EUT LEFT VIEW OF EUT

Report No.: AGC04900161002FE03 Page 30 of 31 RIGHT VIEW OF EUT OPEN VIEW OF EUT

Report No.: AGC04900161002FE03 Page 31 of 31 INTERNAL VIEW OF EUT-1 Antenna INTERNAL VIEW OF EUT-2 ----END OF REPORT----


Document Created: 2016-11-08 06:13:22
Document Modified: 2016-11-08 06:13:22
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC