Test Report

FCC ID: 2AANZCODQDRMQ27

Test Report

Download: PDF
FCCID_3201590

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Report No.: SZEM160900759202 Email: ee.shenzhen@sgs.com Page: 1 of 30 1 Cover page FCC REPORT Application No. : SZEM1609007592CR Applicant: DGL Group, Ltd Product Name: CALL OF DUTY MQ-27 STUNT DRONE Model No.(EUT): COD-QDR-MQ27 Trade Mark: Call of Duty FCC ID: 2AANZCODQDRMQ27 Standards: 47 CFR Part 15, Subpart C (2015) Date of Receipt: 2016-09-06 Date of Test: 2016-09-07 to 2016-09-14 Date of Issue: 2016-09-18 Test Result: PASS * . * In the configuration tested, the EUT complied with the standards specified above. Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. ”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 2 of 30 2 Version Revision Record Version Chapter Date Modifier Remark 00 2016-09-18 Original Authorized for issue by: Tested By 2016-09-14 (Gebin Sun) /Project Engineer Date Checked By 2016-09-18 (Eric Fu) /Reviewer Date This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 3 of 30 3 Test Summary Test Item Test Requirement Test method Result 47 CFR Part 15, Subpart C Section Antenna Requirement ANSI C63.10 (2013) PASS 15.203 Field Strength of the 47 CFR Part 15, Subpart C Section ANSI C63.10 (2013) PASS Fundamental Signal 15.249 (a) 47 CFR Part 15, Subpart C Section Spurious Emissions ANSI C63.10 (2013) PASS 15.249 (a)/15.209 Restricted bands around fundamental 47 CFR Part 15, Subpart C Section ANSI C63.10 (2013) PASS frequency (Radiated 15.249(a)/15.205 Emission) 20dB Occupied 47 CFR Part 15, Subpart C Section ANSI C63.10 (2013) PASS Bandwidth 15.215 (c) This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 4 of 30 4 Contents Page 1 COVER PAGE........................................................................................................................................... 1 2 VERSION .................................................................................................................................................. 2 3 TEST SUMMARY ..................................................................................................................................... 3 4 CONTENTS .............................................................................................................................................. 4 5 GENERAL INFORMATION ...................................................................................................................... 5 5.1 CLIENT INFORMATION .............................................................................................................................. 5 5.2 GENERAL DESCRIPTION OF EUT ............................................................................................................. 5 5.3 TEST ENVIRONMENT AND MODE .............................................................................................................. 7 5.4 DESCRIPTION OF SUPPORT UNITS ........................................................................................................... 7 5.5 TEST LOCATION ...................................................................................................................................... 7 5.6 TEST FACILITY ........................................................................................................................................ 8 5.7 DEVIATION FROM STANDARDS ................................................................................................................. 8 5.8 ABNORMALITIES FROM STANDARD CONDITIONS ........................................................................................ 8 5.9 OTHER INFORMATION REQUESTED BY THE CUSTOMER ............................................................................. 8 5.10 EQUIPMENT LIST ................................................................................................................................. 9 6 TEST RESULTS AND MEASUREMENT DATA .................................................................................... 11 6.1 ANTENNA REQUIREMENT ....................................................................................................................... 11 6.2 SPURIOUS EMISSIONS ........................................................................................................................... 12 6.2.1 Spurious Emissions .................................................................................................................... 12 6.3 RESTRICTED BANDS AROUND FUNDAMENTAL FREQUENCY ....................................................................... 21 6.4 20DB BANDWIDTH ................................................................................................................................. 27 7 PHOTOGRAPHS (TEST MODEL NO.:COD-QDR-MQ27) ........................................... 30 7.1 RADIATED EMISSION TEST SETUP.......................................................................................................... 30 RADIATED SPURIOUS EMISSION ................................................................................................................. 30 7.2 ................................................................................................................................................................ 30 7.3 EUT CONSTRUCTIONAL DETAILS ........................................................................................................... 30 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 5 of 30 5 General Information 5.1 Client Information Applicant: DGL Group, Ltd Address of Applicant: 195 Raritan Center Parkway Edison, NJ 08837 5.2 General Description of EUT Product Name: CALL OF DUTY MQ-27 STUNT DRONE Model No.: COD-QDR-MQ27 Trade Mark : Call of Duty Frequency Range: 2410MHz~2475MHz Modulation Type: GFSK Sample Type: Portable production Antenna Type: Integral Antenna Gain: 0dBi power Supply: 4.5V DC (1.5Vx3 "AA" Size Batteries) for Remote controller This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 6 of 30 In section 15.31(m), regards to the operating frequency range over 10 MHz, the Lowest frequency, the middle frequency, and the highest frequency of channel were selected to perform the test, and the selected channel see below: Channel Frequency The Lowest channel 2410MHz The Middle channel 2445MHz The Highest channel 2475MHz This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 7 of 30 5.3 Test Environment and Mode Operating Environment: Temperature: 25.0 °C Humidity: 52 % RH Atmospheric Pressure: 1010 mbar Test mode: Transmitting mode: Keep the EUT in transmitting mode with modulation. 5.4 Description of Support Units The EUT has been tested independently. 5.5 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen BranchNo. 1 Workshop, M-10, Middle Section, Science & Technology Park, Shenzhen, Guangdong, China. 518057. Tel: +86 755 2601 2053 Fax: +86 755 2671 0594 No tests were sub-contracted. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 8 of 30 5.6 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • CNAS (No. CNAS L2929) CNAS has accredited SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 10m Semi-anechoic chamber and Shielded Room of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-823, R-4188, T-1153 and C-2383 respectively. • FCC – Registration No.: 556682 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration No.: 556682. • Industry Canada (IC) Two 3m Semi-anechoic chambers and the 10m Semi-anechoic chamber of SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab have been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 4620C-1, 4620C-2, 4620C-3. 5.7 Deviation from Standards None. 5.8 Abnormalities from Standard Conditions None. 5.9 Other Information Requested by the Customer None. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 9 of 30 5.10 Equipment List RF connected test Cal. date Cal.Due date Item Test Equipment Manufacturer Model No. Inventory No. (yyyy-mm-dd) (yyyy-mm-dd) 1 DC Power Supply ZhaoXin RXN-305D SEM011-02 2015-10-09 2016-10-09 Rohde & 2 Spectrum Analyzer FSP SEM004-06 2015-10-17 2016-10-17 Schwarz Rohde & 3 Signal Generator SML03 SEM006-02 2016-04-25 2017-04-25 Schwarz Rohde & 4 Power Meter NRVS SEM014-02 2015-10-09 2016-10-09 Schwarz RE in Chamber Cal.Due Model Inventory Cal. date Item Test Equipment Manufacturer date No. No. (yyyy-mm-dd) (yyyy-mm-dd) 3m Semi-Anechoic ETS- 1 N/A SEM001-01 2016-05-13 2017-05-13 Chamber LINDGREN Agilent 2 EMI Test Receiver N9038A SEM004-05 2015-09-16 2016-09-16 Technologies BiConiLog Antenna ETS- 3 3142C SEM003-01 2014-11-01 2017-11-01 (26-3000MHz) LINDGREN Double-ridged horn ETS- 4 3117 SEM003-11 2015-10-17 2018-10-17 (1-18GHz) LINDGREN Horn Antenna ETS- 5 3160 SEM003-12 2014-11-24 2017-11-24 (18-26GHz) LINDGREN Pre-amplifier Agilent 6 8447D SEM005-01 2016-04-25 2017-04-25 (0.1-1300MHz) Technologies 7 Band filter Amindeon Asi 3314 SEM023-01 N/A N/A 8 DC Power Supply Zhao Xin RXN-305D SEM011-02 2015-10-09 2016-10-09 9 Loop Antenna Beijing Daze ZN30401 SEM003-09 2015-05-13 2018-05-13 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 10 of 30 RE in Chamber Inventory Cal. date Cal.Due date Item Test Equipment Manufacturer Model No. No. (yyyy-mm-dd) (yyyy-mm-dd) 3m Semi-Anechoic 1 AUDIX N/A SEM001-02 2016-05-13 2017-05-13 Chamber 2 EMI Test Receiver Rohde & Schwarz ESIB26 SEM004-04 2016-04-25 2017-04-25 BiConiLog Antenna 3 ETS-Lindgren 3142C SEM003-02 2014-11-15 2017-11-15 (26-3000MHz) Amplifier 4 HP 8447D SEM005-02 2015-10-09 2016-10-09 (0.1-1300MHz) Horn Antenna 5 Rohde & Schwarz HF907 SEM003-07 2015-06-14 2018-06-14 (1-18GHz) Horn Antenna 6 ETS-Lindgren 3160 SEM003-12 2014-11-24 2017-11-24 (18-26GHz) Horn Antenna 7 A.H.Systems, inc. SAS-573 SEM003-13 2015-02-12 2018-02-12 (26GHz-40GHz) BDLNA- Black Diamond 8 Low Noise Amplifier 0118- SEM005-05 2015-10-09 2016-10-09 Series 352810 9 Band filter Amindeon Asi 3314 SEM023-01 N/A N/A This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 11 of 30 6 Test results and Measurement Data 6.1 Antenna Requirement Standard requirement: 47 CFR Part 15C Section 15.203 15.203 requirement: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. EUT Antenna: The antenna is integrated on the main PCB and no consideration of replacement. The best case gain of the antenna is 0dBi. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS—CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZENM180000759z02 Page: 12 ot 30 6.2. Spurious Emissions 6.2.1 Spurious Emissions Test Requrement: 47 GFR Pat 150 Section 15 249 and 15209 Test Method: ANSI 03 10; 2013 Gause 5455 and 66 Test Ste Measurement Disance: am Recaver Setup Frequency Detector new vew Remark o oostti0 ocotfie Poak Togt sooe Posk o oostti—0 ocotie Averace Totle _|_s08ie Average 0.090147—0.110tiie Guasipeas tocide 300b Guasipeak o rroue0.asotle Poak Togt sooe Posk o 11oliz—0.000ie Averace Toble 30e Averace 090Ve Solle Quesipeck 10e 30e Quesipeck sovbte162 Quasipesk |_tookile 8001612 Quesipek Posk We sume Posk Above 1Gite Posk wz t Averace Uimit Fied strength umt Measuremont (Spurious Emissions Frequency (mierovotiimete oiy P®M2K astance (m] 1 o comte—0.asoiite 20077 Gite) — — &0 o.isomie—1.7osvite 240007(ite) — — so 1rost—sovlte > — — so souitseuite 10 40. | Guasipeak s sovie2rsMe 1so 435 Guasipeak s 2ioleacovite zo 45. | Guasipeak s seovtte16it soo sa0 Quasipeak s Above 16z soo 540 |_Average s Nete: 15 35(b, Unless othennise specifed, re Imt on peak redio frequency onissions is 20dB above the maximum permited average emission imapplcable to the equlpment under test. This peak limk appes to the total poak emision level radiated by e device Un Frequeney Lint (dBuim @gm) Rematk (Feldstrongth ofthe o Average Vave furdementalsignal) racobtt—2sss shite mao Poak value Piiretiventtrncmmecnueesnanoi nnecnnmcuonainanee uons npcssacmincreninmestanaszes Inaounonleimmoindoreanenen,mimmmnetemciine

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 13 of 30 Test Setup: Figure 1. Below 30MHz Figure 2. 30MHz to 1GHz Figure 3. Above 1 GHz Test Procedure: a. For below 1GHz, the EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. b. For above 1GHz, the EUT was placed on the top of a rotating table 1.5 meters above the ground at a 3 meter fully-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation c. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. d. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. e. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters (for the test frequency of below 30MHz, the antenna was tuned to heights 1 meter) and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. f. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. g. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 14 of 30 h. Test the EUT in the lowest channel, the middle channel, the Highest channel i. The radiation measurements are performed in X, Y, Z axis positioning for Transmitting mode,And found the X axis positioning which it is worse case. j. Repeat above procedures until all frequencies measured was complete. Instruments Used: Refer to section 5.10 for details Exploratory Test Mode: Transmitting mode Final Test Mode: Pretest the EUT at Transmitting mode, found the Transmitting mode which it is worse case Only the worst case is recorded in the report. Test Results: Pass This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 15 of 30 Measurement Data 6.2.1.1 Field Strength Of The Fundamental Signal Peak value: Antenna Cable Preamp Read Over Frequency Level Limit Line Factor Loss Factor Level Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dB/m) (dB) (dB) (dBuV) (dB) 2410.114 29.14 5.35 38.15 103.29 99.63 114.00 -14.37 Horizontal 2410.114 29.14 5.35 38.15 94.32 90.66 114.00 -23.34 Vertical 2445.126 29.24 5.38 38.15 102.8 99.27 114.00 -14.73 Horizontal 2445.126 29.24 5.38 38.15 96.74 93.21 114.00 -20.79 Vertical 2475.424 29.33 5.4 38.15 101.28 97.86 114.00 -16.14 Horizontal 2475.474 29.33 5.4 38.15 95.75 92.33 114.00 -21.67 Vertical Average value: Cable Antenna Preamp Read Over Frequency Level Limit Line Loss Factor Factor Level Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dB) (dB/m) (dB) (dBuV) (dB) 2410.114 29.14 5.35 38.15 94.56 90.90 94.00 -3.10 Horizontal 2445.126 29.24 5.38 38.15 93.69 90.16 94.00 -3.84 Horizontal 2475.424 29.33 5.40 38.15 94.31 90.89 94.00 -3.11 Horizontal This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 16 of 30 6.2.1.2 Spurious Emissions 30MHz~1GHz Test mode: Transmitting mode Vertical This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 17 of 30 Test mode: Transmitting mode Horizontal This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 18 of 30 Above 1GHz Test mode: Transmitting Test channel: Lowest Remark: Peak Antenna Cable Preamp Read Over Frequency Level Limit Line Factor Loss Factor Level Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dB/m) (dB) (dB) (dBuV) (dB) 3653.574 32.65 7.69 38.54 44.13 45.93 74 -28.07 Vertical 4820.000 34.19 8.89 39.03 52.65 56.70 74 -17.30 Vertical 6077.331 34.76 10.46 38.95 45.33 51.60 74 -22.40 Vertical 7230.000 36.41 10.69 38.16 47.18 56.12 74 -17.88 Vertical 9640.000 37.53 12.52 36.97 40.28 53.36 74 -20.64 Vertical 11856.680 38.46 14.41 38.16 38.50 53.21 74 -20.79 Vertical 3780.095 33.01 7.73 38.60 45.84 47.98 74 -26.02 Horizontal 4820.000 34.19 8.89 39.03 55.02 59.07 74 -14.93 Horizontal 6055.591 34.75 10.49 38.96 44.37 50.65 74 -23.35 Horizontal 7230.000 36.41 10.69 38.16 47.51 56.45 74 -17.55 Horizontal 9640.000 37.53 12.52 36.97 40.57 53.65 74 -20.35 Horizontal 11856.680 38.46 14.41 38.16 38.40 53.11 74 -20.89 Horizontal Test mode: Transmitting Test channel: Lowest Remark: Average Antenna Cable Preamp Read Over Frequency Level Limit Line Factor Loss Factor Level Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dB/m) (dB) (dB) (dBuV) (dB) 4820.000 34.19 8.89 39.03 37.85 41.90 54 -12.10 Vertical 7230.000 36.41 10.69 38.16 31.74 40.68 54 -13.32 Vertical 4820.000 34.19 8.89 39.03 34.95 39.00 54 -15.00 Horizontal 7230.000 36.41 10.69 38.16 31.74 40.68 54 -13.32 Horizontal This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 19 of 30 Test mode: Transmitting Test channel: Middle Remark: Peak Antenna Cable Preamp Read Over Frequency Level Limit Line Factor Loss Factor Level Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dB/m) (dB) (dB) (dBuV) (dB) 3582.269 32.44 7.66 38.51 44.23 45.82 74 -28.18 Vertical 4890.000 34.31 8.99 39.06 52.42 56.66 74 -17.34 Vertical 6077.331 34.76 10.46 38.95 45.01 51.28 74 -22.72 Vertical 7335.000 36.36 10.73 38.05 44.43 53.47 74 -20.53 Vertical 9780.000 37.56 12.59 36.91 40.13 53.37 74 -20.63 Vertical 11439.320 38.05 13.95 37.75 39.04 53.29 74 -20.71 Vertical 3786.875 33.03 7.74 38.60 45.71 47.88 74 -26.12 Horizontal 4890.000 34.31 8.99 39.06 53.81 58.05 74 -15.95 Horizontal 6055.591 34.75 10.49 38.96 44.87 51.15 74 -22.85 Horizontal 7335.314 36.36 10.73 38.05 44.08 53.12 74 -20.88 Horizontal 9780.000 37.56 12.59 36.91 40.71 53.95 74 -20.05 Horizontal 11856.680 38.46 14.41 38.16 38.87 53.58 74 -20.42 Horizontal Test mode: Transmitting Test channel: Middle Remark: Average Antenna Cable Preamp Read Over Frequency Level Limit Line Factor Loss Factor Level Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dB/m) (dB) (dB) (dBuV) (dB) 4890.000 34.31 8.99 39.06 36.62 40.86 54 -13.14 Vertical 4890.000 34.31 8.99 39.06 37.67 41.91 54 -12.09 Horizontal This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 20 of 30 Test mode: Transmitting Test channel: Highest Remark: Peak Antenna Cable Preamp Read Over Frequency Level Limit Line Factor Loss Factor Level Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dB/m) (dB) (dB) (dBuV) (dB) 3759.831 32.95 7.73 38.59 44.65 46.74 74 -27.26 Vertical 4950.000 34.41 9.07 39.08 52.38 56.78 74 -17.22 Vertical 5779.957 34.57 9.94 39.02 45.11 50.60 74 -23.40 Vertical 7425.000 36.33 10.76 37.96 43.79 52.92 74 -21.08 Vertical 9900.000 37.58 12.66 36.85 39.61 53.00 74 -21.00 Vertical 12136.100 38.68 14.45 38.44 39.04 53.73 74 -20.27 Vertical 3588.694 32.46 7.66 38.51 45.02 46.63 74 -27.37 Horizontal 4950.000 34.41 9.07 39.08 54.57 58.97 74 -15.03 Horizontal 6077.331 34.76 10.46 38.95 45.10 51.37 74 -22.63 Horizontal 7425.000 36.33 10.76 37.96 43.45 52.58 74 -21.42 Horizontal 9900.000 37.58 12.66 36.85 39.83 53.22 74 -20.78 Horizontal 11625.290 38.23 14.16 37.94 39.26 53.71 74 -20.29 Horizontal Test mode: Transmitting Test channel: Highest Remark: Average Antenna Cable Preamp Read Over Frequency Level Limit Line Factor Loss Factor Level Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dB/m) (dB) (dB) (dBuV) (dB) 4950.000 34.41 9.07 39.08 37.40 41.80 54 -12.20 Vertical 4950.000 34.41 9.07 39.08 35.20 39.60 54 -14.40 Horizontal Remark: 1) The field strength is calculated by adding the Antenna Factor, Cable Factor & Preamplifier. The basic equation with a sample calculation is as follows: Final Test Level =Receiver Reading + Antenna Factor + Cable Factor – Preamplifier Factor 2) Scan from 9kHz to 25GHz,The disturbance above 13GHz and below 30MHz was very low, and the above harmonics were the highest point could be found when testing, so only the above harmonics had been displayed. The amplitude of spurious emissions from the radiator which are attenuated more than 20dB below the limit need not be reported . 3) As shown in this section, for frequencies above 1GHz, the field strength limits are based on average limits. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 21 of 30 6.3 Restricted bands around fundamental frequency Test Requirement: 47 CFR Part 15C Section 15.209 and 15.205 Test Method: ANSI C63.10: 2013 Clause 6.10 Test site: Measurement Distance: 3m Limit(band edge): Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits in Section 15.209, whichever is the lesser attenuation. Frequency Limit (dBuV/m @3m) Remark 30MHz-88MHz 40.0 Quasi-peak Value 88MHz-216MHz 43.5 Quasi-peak Value 216MHz-960MHz 46.0 Quasi-peak Value 960MHz-1GHz 54.0 Quasi-peak Value 54.0 Average Value Above 1GHz 74.0 Peak Value Test Setup: Figure 1. 30MHz to 1GHz Figure 2. Above 1 GHz This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 22 of 30 Test Procedure: a. For below 1GHz, the EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. b. For above 1GHz, the EUT was placed on the top of a rotating table 1.5 meters above the ground at a 3 meter fully-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. c. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. d. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. e. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. f. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. g. Place a marker at the end of the restricted band closest to the transmit frequency to show compliance. Also measure any emissions in the restricted bands. Save the spectrum analyzer plot. Repeat for each power and modulation for lowest and highest channel h. Test the EUT in the lowest channel , the Highest channel i. The radiation measurements are performed in X, Y, Z axis positioning for Transmitting mode, And found the X axis positioning which it is worse case. j. Repeat above procedures until all frequencies measured was complete. Instruments Used: Refer to section 5.10 for details Exploratory Test Mode: Transmitting mode Final Test Mode: Pretest the EUT at Transmitting mode, found the Transmitting mode which it is worse case Only the worst case is recorded in the report. Test Results: Pass This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 23 of 30 Band edge (Radiated Emission) Test mode: Transmitting mode. Test channel: Lowest Remark: Peak Vertical This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 24 of 30 Test mode: Transmitting mode. Test channel: Lowest Remark: Peak Horizontal This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 25 of 30 Test mode: Transmitting mode. Test channel: Highest Remark: Peak Vertical This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 26 of 30 Test mode: Transmitting mode. Test channel: Highest Remark: Peak Horizontal Note: The field strength is calculated by adding the Antenna Factor, Cable Factor & Preamplifier. The basic equation with a sample calculation is as follows: Final Test Level =Receiver Reading + Antenna Factor + Cable Factor – Preamplifier Factor This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 27 of 30 6.4 20dB Bandwidth Test Requirement: 47 CFR Part 15C Section 15.215 Test Method: ANSI C63.10:2013 Clause 6.9 Test Setup: Instruments Used: Refer to section 5.10 for details Test mode: Transmitting mode Limit: N/A Test Results: Pass Measurement Data Test channel 20dB bandwidth (MHz) Results Lowest 2.94 Pass Middle 2.28 Pass Highest 2.08 Pass This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 28 of 30 Test plot as follows: Test channel: Lowest * RBW 30 kHz Delta 3 [T1 ] * VBW 100 kHz 1.08 dB Ref 20 dBm * Att 40 dB SWT 25 ms 2.940000000 MHz 20 Marker 1 [T1 ] -19.10 dBm 2.408820000 GHz A 10 2 Marker 2 [T1 ] 1 PK 2.54 dBm MAXH 0 2.410120000 GHz -10 1 3 D1 -17.46 dBm -20 -30 3DB -40 -50 -60 -70 -80 Center 2.4102 GHz 2 MHz/ Span 20 MHz Test channel: Middle * RBW 30 kHz Delta 3 [T1 ] * VBW 100 kHz 3.66 dB Ref 20 dBm * Att 40 dB SWT 25 ms 2.280000000 MHz 20 Marker 1 [T1 ] -26.94 dBm 2.444320000 GHz A 10 Marker 2 [T1 ] 1 PK 2 2.20 dBm MAXH 0 2.445120000 GHz -10 D1 -17.8 dBm -20 3 1 -30 3DB -40 -50 -60 -70 -80 Center 2.4452 GHz 2 MHz/ Span 20 MHz This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 29 of 30 Test channel: Highest * RBW 30 kHz Delta 3 [T1 ] * VBW 100 kHz 4.83 dB Ref 20 dBm * Att 40 dB SWT 25 ms 2.080000000 MHz 20 Marker 1 [T1 ] -22.93 dBm 2.474360000 GHz A 10 Marker 2 [T1 ] 1 PK 2 1.90 dBm MAXH 0 2.475120000 GHz -10 3 D1 -18.1 dBm -20 1 -30 3DB -40 -50 -60 -70 -80 Center 2.4752 GHz 2 MHz/ Span 20 MHz This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM160900759202 Page: 30 of 30 7 Photographs (Test model No.:COD-QDR-MQ27) 7.1 Radiated Emission Test Setup 7.2 Radiated Spurious Emission 7.3 EUT Constructional Details Refer to Appendix A - Photographs of EUT Constructional Details for SZEM1609007592CR. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.


Document Created: 2016-11-21 08:00:11
Document Modified: 2016-11-21 08:00:11
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC