Test Report_DTS

FCC ID: 2AAMI-T2030

Test Report

Download: PDF
FCCID_4191758

FCC and IC Test Report for Parts 15.247, 15.249, 15.209 and RSS-247, RSS Gen, RSS-210 Product name : T2030 Applicant : Tacx FCC ID : 2AAMI-T2030 IC ID : 11353A-T2030 Test report No. : 180801587 003 Ver 3.00

Report number: 180801587 003 Ver 3.00 Laboratory information Accreditation Telefication complies with the accreditation criteria for test laboratories as laid down in ISO/IEC 17025:2005. The accreditation covers the quality system of the laboratory as well as the specific activities as described in the authorized annex bearing the accreditation number L021 and is granted on 30 November 1990 by the Dutch Council For Accreditation (RvA: Raad voor Accreditatie). Telefication is designated by the FCC as an Accredited Test Firm for compliance testing of equipment subject to Certification under Parts 15 & 18. The Designation number is: NL0001. Telefication is a Wireless Device Testing laboratory recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements. The Industry Canada registration number for the 3 meter test chamber of Telefication is: 4173A-1. Documentation The test report must always be reproduced in full; reproduction of an excerpt only is subject to written approval of the testing laboratory. The documentation of the testing performed on the tested devices is archived for 10 years at Telefication Netherlands. Testing Location Test Site Telefication BV Test Site location Edisonstraat 12a 6902 PK Zevenaar The Netherlands Tel. +31889983600 Fax. +31316583189 Test Site FCC NL0001 Page 1 of 32

Report number: 180801587 003 Ver 3.00 Revision History Version Date Remarks By v0.50 11-12-2018 First draft PvW v1.00 15-02-2019 Initial release PvW v2.00 01-03-2019 Added field strength of fundamental to PVW ANT/ANT+ in clause 3.3.5 v3.00 06-03-2019 Updated emission designator for ANT+ PVW from 1M00F7D to 1M00F1D Page 2 of 32

Report number: 180801587 003 Ver 3.00 Table of Contents Revision History .............................................................................................................................................. 2 Summary of Test results .................................................................................................................................. 5 1 General Description ................................................................................................................................. 6 1.1 Applicant................................................................................................................................................6 1.2 Manufacturer ........................................................................................................................................6 1.3 Tested Equipment Under Test (EUT) .....................................................................................................6 1.4 Product specifications of Equipment under test ...................................................................................7 1.5 Modification of the Equipment Under Test (EUT) .................................................................................7 1.6 Observations and remarks.....................................................................................................................7 1.7 Environmental conditions......................................................................................................................7 1.8 Measurement Standards .......................................................................................................................7 1.9 Applicable Standards .............................................................................................................................7 1.10 Conclusions ............................................................................................................................................8 2 Test configuration of the Equipment Under Test ..................................................................................... 9 2.1 Test mode ..............................................................................................................................................9 2.2 Tested channels and Data rates ............................................................................................................9 2.3 Test setups .............................................................................................................................................9 2.4 Equipment used in the test configuration ...........................................................................................10 2.5 Sample calculation ...............................................................................................................................10 3 Test results ............................................................................................................................................ 11 3.1 6dB bandwidth Measurement .............................................................................................................11 3.1.1 Limit.................................................................................................................................................11 3.1.2 Measurement instruments .............................................................................................................11 3.1.3 Test setup ........................................................................................................................................11 3.1.4 Test procedure ................................................................................................................................11 3.1.5 Test Results of the 6 dB bandwidth Measurement .........................................................................11 3.2 99% Occupied Bandwidth ....................................................................................................................12 3.2.1 Limit.................................................................................................................................................12 3.2.2 Measurement instruments .............................................................................................................12 3.2.3 Test setup ........................................................................................................................................12 3.2.4 Test procedure ................................................................................................................................12 3.2.5 Test results of the 99% occupied bandwidth measurement...........................................................12 3.2.6 Plots of the BLE V5.0 99% occupied bandwidth measurement ......................................................13 3.2.7 Plots of the ANT 99% Occupied bandwidth measurement .............................................................15 3.2.8 Plot of the ANT+ 99% occupied bandwidth measurement .............................................................16 3.3 Output Power Measurement ..............................................................................................................17 3.3.1 Limit.................................................................................................................................................17 Page 3 of 32

Report number: 180801587 003 Ver 3.00 3.3.2 Measurement instruments .............................................................................................................17 3.3.3 Test setup ........................................................................................................................................17 3.3.4 Test procedure ................................................................................................................................17 3.3.5 Test results of Output Power Measurement...................................................................................17 3.4 Power Spectral Density........................................................................................................................18 3.4.1 Limit.................................................................................................................................................18 3.4.2 Measurement instruments .............................................................................................................18 3.4.3 Test setup ........................................................................................................................................18 3.4.4 Test procedure ................................................................................................................................18 3.4.5 Test results of Power Spectral Density Measurement ....................................................................18 3.5 Band edge Measurement ....................................................................................................................19 3.5.1 Limit.................................................................................................................................................19 3.5.2 Measurement instruments .............................................................................................................19 3.5.3 Test setup ........................................................................................................................................19 3.5.4 Test procedure ................................................................................................................................19 3.5.5 Measurement Uncertainty ..............................................................................................................19 3.5.6 Plots of the Band edge Measurements ...........................................................................................19 3.6 Radiated Spurious Emissions Measurement .......................................................................................21 3.6.1 Limit.................................................................................................................................................21 3.6.2 Measurement instruments .............................................................................................................21 3.6.3 Test setup ........................................................................................................................................21 3.6.4 Test procedure ................................................................................................................................21 3.6.5 Notes ...............................................................................................................................................21 3.6.6 Plots of the Radiated Spurious Emissions (BLE V5.0) ......................................................................22 3.6.7 Plots of the Radiated Spurious Emissions (ANT) .............................................................................27 3.6.8 Measurement Uncertainty ..............................................................................................................32 Page 4 of 32

Report number: 180801587 003 Ver 3.00 Summary of Test results FCC ISED Description Section in Verdict report 15.247 (a) RSS-247 5.2(a) 6dB Bandwidth 3.1 Pass -- RSS-Gen 6.7 99% Bandwidth 3.2 Pass 15.247 (b) RSS-247 5.1 (b) RF output power 3.3 Pass 15.247 (e) RSS-247 5.2 (b) Power spectral density 3.4 Pass 15.247 (d) RSS-247 5.5 Band edge 3.5 Pass 15.209 (a) RSS-247 5.4 Radiated emissions 3.6 Pass RSS-Gen 8.9 RSS-210 B.10 15.205 (a) RSS-Gen 8.10 Spurious emissions in the restricted bands 3.6 Pass RSS-210 B.10 Page 5 of 32

Report number: 180801587 003 Ver 3.00 1 General Description 1.1 Applicant Client name: Tacx b.v. Address Rijksstraatweg 52, Wassenaar, the Netherlands Zip code: 2241BW Telephone: +31 (0)705119259 E-mail: martin@tacx.nl Contact name: Martin Smits 1.2 Manufacturer Manufacturer name: Tacx b.v. Address: Rijksstraatweg 52, Wassenaar, the Netherlands Zip code: 2241BW Telephone: +31 (0)705119259 E-mail: martin@tacx.nl Contact name: Martin Smits 1.3 Tested Equipment Under Test (EUT) Product name: T2030 Brand name: Tacx Product type: Power meter FCC ID: 2AAMI-T2030 IC ID 11353A-T2030 Software version: -- Hardware version: V08 Date of receipt 15-10-2018 Tests started: 15-10-2018 Testing ended: 14-02-2019 Page 6 of 32

Report number: 180801587 003 Ver 3.00 1.4 Product specifications of Equipment under test TX Frequency range (MHz) BLE V5.0: 2400 – 2483.5 ANT: 2400 – 2483.5 ANT+: 2450 and 2457 MHz1 RX frequency range (MHz) BLE V5.0: 2400 – 2483.5 ANT: 2400 – 2483.5 ANT+: 2450 and 2457 MHz1 Maximum output power to antenna (dBm) -0.68 Antenna type Ceramic chip antenna Antenna gain (dBi) -2.0 Type of modulation ANT; ANT+: GFSK BLE V5.0: GFSK Emission designator BLE (V5.0) 2M21F7D Emission designator ANT+ 1M00F1D Note 1: ANT+ uses the same modulation techniques and transmission power as ANT. Measurements on ANT are considered representative for all ANT+ frequencies. See clause 3.2.8 for a comparison of the signals. 1.5 Modification of the Equipment Under Test (EUT) The manufacturer provided both a radiated sample and a conducted sample for radio testing. 1.6 Observations and remarks For the ANT radio, only RF power, 99% occupied bandwidth and radiated spurious emissions tests are applicable. Measurements of the ANT technology are considered representative for all frequencies of the ANT+ technology because ANT+ uses the same modulation techniques and transmission power as ANT. The EUT uses ANT+ when possible, but switches to ANT when communicating with a non-ANT+ device. For the BLE V5.0 radio, all tests in this test report are applicable. Spurious emissions in the 9 kHz – 30 MHz range are not reported as these emissions are more than 20 dB below the transmission level. 1.7 Environmental conditions Test date 31-10-2018 01-11-2018 14-02-2019 Ambient temperature 19.2 °C 20.3 °C 20.3 °C Humidity 42.8 % 41.8 % 39.7 % 1.8 Measurement Standards • ANSI C63.10:2013 1.9 Applicable Standards According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards: • FCC Part 15 Subpart C §15.247, §15.249, §15.209 • RSS-247 Issue 2, RSS-Gen Issue 5, RSS-210 Issue 9 Page 7 of 32

Report number: 180801587 003 Ver 3.00 1.10 Conclusions The sample of the product showed NO NON-COMPLIANCES to the specifications stated in paragraph 1.9 of this report. The results of the test as stated in this report, are exclusively applicable to the product items as identified in this report. Telefication accepts no responsibility for any properties of product items in this test report, which are not supported by the tests as specified in paragraph 1.9 “Applicable standards”. All tests are performed by: Name : P. van Wanrooij, BASc Review of test methods and report by: Name : ing. R. van Barneveld The above conclusions have been verified by the following signatory: Date : 06-03-2019 Name : ing. K.A. Roes Function : Coordinator Radio Laboratory Signature : Page 8 of 32

Report number: 180801587 003 Ver 3.00 2 Test configuration of the Equipment Under Test 2.1 Test mode The applicant provided test mode firmware for the EUT, in which it was possible to configure the EUT into different test channels. 2.2 Tested channels and Data rates 2 Mbps BLE V5.0 has not been tested because the RF chip of the EUT only supports 1 Mbps BLE V5.0. Technology Channels Data rate Frequency (MHz) 1 (Low) 1 Mbps 2402 Bluetooth Low Energy V5.0 18 (Mid) 1 Mbps 2440 39 (High) 1 Mbps 2480 Technology Channels Data rate Frequency (MHz) 1 (Low) 1 Mbps 2402 ANT 39 (Mid) 1 Mbps 2440 78 (High) 1 Mbps 2480 Technology Channels Data rate Frequency (MHz) ANT+ -- 1 Mbps 2457 2.3 Test setups Radiated emissions test setup 30 MHz - 1 GHz Page 9 of 32

Report number: 180801587 003 Ver 3.00 Radiated emissions test setup above 1 GHz 2.4 Equipment used in the test configuration Description Test setup number Used at paragraphs Radiated emission measurement TS 00004 3.6 system Conducted emission radio TS 00008 3.1 – 3.5 equipment Description Manufacturer Model Equipment ID Used at paragraphs Spectrum analyser Rohde & Schwarz FSV40 TE 11160 3.1 – 3.5 High pass filter Wainwright WHK10-2520-30 TE 11146 3.6 Software DARE Instruments Radimation -- 3.6 2018.1.5 2.5 Sample calculation Field Strength Measurement example: Frequency (GHz) Polarization Height(m) Peak (dBµV/m) 7,32 Horizontal 2 47.9 The following relation applies: E (dBµV/m) = U(dBµV) + AF (dB/m) – G (dB) + CL (dB) Where: E = Electric field strength U = Measuring receiver voltage AF = Antenna factor G = Gain of the pre-amplifier CL = Cable loss (52.5 = 48.12 + 36.1 - 37.42 + 5.7) Page 10 of 32

Report number: 180801587 003 Ver 3.00 3 Test results 3.1 6dB bandwidth Measurement 3.1.1 Limit The minimum 6 dB Bandwidth shall be at least 500 kHz. 3.1.2 Measurement instruments The measurement instruments are listed in chapter 2.4 of this report. 3.1.3 Test setup The test setup is as shown in chapter 2.3 of this report. 3.1.4 Test procedure Tests according to ANSI C63.10. IRN 017 - Occupied bandwidth (Hz) Method 4 – DTS Bandwidth. 3.1.5 Test Results of the 6 dB bandwidth Measurement Frequency 6dB bandwidth Technology Std. Channel Data rate (MHz) (kHz) 1 2402 1 Mbps 1133.8 Bluetooth Low energy 18 2440 1 Mbps 1129.5 V5.0 39 2480 1 Mbps 1133.8 Uncertainty ± 36.2 kHz Page 11 of 32

Report number: 180801587 003 Ver 3.00 3.2 99% Occupied Bandwidth 3.2.1 Limit According to RSS-Gen 6.7. 3.2.2 Measurement instruments The measurement instruments are listed in chapter 2.4 of this report. 3.2.3 Test setup The test setup is as shown in chapter 2.3 of this report. 3.2.4 Test procedure IRN 017 - Occupied bandwidth (Hz) Method 1 – XX % power bandwidth. 1. Set the centre frequency to the nominal EUT channel centre frequency 2. Set span = 1.5 times to 0.5 times the Occupied Bandwidth 3. Set VBW ≥ 3x RBW 4. Video averaging is not permitted. Where practical, detection and single sweep mode shall be used. Otherwise, peak detection and max hold mode (until the trace stabilizes) shall be used. 3.2.5 Test results of the 99% occupied bandwidth measurement Frequency 99% bandwidth Technology Std. Channel Data rate (MHz) (kHz) 1 2402 1 Mbps 2185 Bluetooth Low energy 18 2440 1 Mbps 2200 V5.0 39 2480 1 Mbps 2214 Uncertainty ± 12 kHz Frequency 99% bandwidth Technology Std. Channel Data rate (MHz) (kHz) 1 2402 1 Mbps 1187 ANT 39 2440 1 Mbps 1187 78 2480 1 Mbps 1187 Uncertainty ± 12 kHz Frequency 99% bandwidth Technology Std. Channel Data rate (MHz) (kHz) ANT+ -- 2457 1 Mbps 1187 Uncertainty ± 12 kHz Page 12 of 32

Report number: 180801587 003 Ver 3.00 3.2.6 Plots of the BLE V5.0 99% occupied bandwidth measurement Channel 1 Channel 18 Page 13 of 32

Report number: 180801587 003 Ver 3.00 Channel 39 Page 14 of 32

Report number: 180801587 003 Ver 3.00 3.2.7 Plots of the ANT 99% Occupied bandwidth measurement Channel 1 Channel 39 Page 15 of 32

Report number: 180801587 003 Ver 3.00 Channel 78 3.2.8 Plot of the ANT+ 99% occupied bandwidth measurement 2457 MHz Page 16 of 32

Report number: 180801587 003 Ver 3.00 3.3 Output Power Measurement 3.3.1 Limit BLE V5.0: For systems using digital modulation in the 2400-2483.5 MHz, the limit for the peak output power is 30 dBm. If transmitting antenna of directional gain greater than 6 dBi is used, the peak output power from the intentional radiator shall be reduced below the above stated value by the amount in dB that the directional gain of the antenna exceeds 6 dBi. In case of point to point operation, the limit has to be reduced by 1 dB for every 3 dB that the directional gain of the antenna exceeds 6 dBi. ANT/ANT+: Field strength of fundamental: 50 mV/m @ 3m. 3.3.2 Measurement instruments The measurement instruments are listed in chapter 2.4 of this report. 3.3.3 Test setup The test setup is as shown in chapter 2.3 of this report. 3.3.4 Test procedure The testing follows ANSI C63.10. IRN 014 - RF power (W) - Method 1 – AVGSA (DTS) according to ANSI C63.10. 3.3.5 Test results of Output Power Measurement Peak method Frequency Peak output power Technology Std. Channel Data rate (MHz) (dBm) 1 2402 1 Mbps -1.31 Bluetooth Low Energy 18 2440 1 Mbps -0.93 V5.0 39 2480 1 Mbps -0.68 Uncertainty ±0.71 dB Field strength of Frequency Peak output Technology Std. Channel Data rate fundamental (MHz) power (dBm) (mV/m @ 3m) 1 2402 1 Mbps -10.10 0.018 ANT 39 2440 1 Mbps -10.40 0.017 78 2480 1 Mbps -9.94 0.18 Uncertainty ±0.71 dB Field strength of Frequency Peak output Technology Std. Channel Data rate fundamental (MHz) power (dBm) (mV/m @ 3m) ANT+ -- 2457 1 Mbps -10.13 0.018 Uncertainty ±0.71 dB Page 17 of 32

Report number: 180801587 003 Ver 3.00 3.4 Power Spectral Density 3.4.1 Limit The peak power spectral density shall not be greater than 8 dBm in any 3 kHz band at any time interval of continuous transmission. 3.4.2 Measurement instruments The measurement instruments are listed in chapter 2.4 of this report. 3.4.3 Test setup The test setup is as shown in chapter 2.3 of this report. 3.4.4 Test procedure The testing follows ANSI C63.10. IRN 030 - Spectral power density (W per n.Hz) - Method 5 – Peak method PKPSD (PSD in 3 kHz band). 3.4.5 Test results of Power Spectral Density Measurement Peak Power spectral density Frequency PSD/3 kHz Technology Std. Channel Data rate (MHz) (dBm) 1 2402 1 Mbps -19.2 Bluetooth Low 18 2440 1 Mbps -18.8 Energy V5.0 39 2480 1 Mbps -18.7 Uncertainty ±2.0 dB Page 18 of 32

Report number: 180801587 003 Ver 3.00 3.5 Band edge Measurement 3.5.1 Limit Band edge: At the edge of the authorized band the RF power shall be at least 20 dB down. 3.5.2 Measurement instruments The measurement instruments are listed in chapter 2.4 of this report. 3.5.3 Test setup The test setup is as shown in chapter 2.3 of this report. 3.5.4 Test procedure According to ANSI C63.10. IRN 026 - Radiated electrical disturbance (V per m) Method 6 – Radiated electrical disturbance at the Authorized band edge. 3.5.5 Measurement Uncertainty ± 5.7 dB. 3.5.6 Plots of the Band edge Measurements See next page. Page 19 of 32

Report number: 180801587 003 Ver 3.00 BLE V5.0 Lower band edge (Channel 1) BLE V5.0 Upper band edge (Channel 39) Page 20 of 32

Report number: 180801587 003 Ver 3.00 3.6 Radiated Spurious Emissions Measurement 3.6.1 Limit The emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: 15.209 Frequency (MHz) Field strength (µV/m) Measurement distance(m) 0.009 – 0.490 2400/F(kHz) 300 0.490 – 1.705 24000/F(kHz) 30 1.705 - 30 30 30 30 -88 100 3 88 - 216 150 3 216-960 200 3 Above 960 500 3 3.6.2 Measurement instruments The measurement instruments are listed in chapter 2.4 of this report. 3.6.3 Test setup The test setup is as shown in chapter 2.3 of this report. 3.6.4 Test procedure Spurious emissions in the 9 kHz – 30 MHz range are not reported as these emissions are more than 20 dB below the transmission level. The emission limits shown in the above table are based on measurements employing a CISPR quasi-peak detector except for the frequency bands 9–90 kHz, 110–490 kHz and above 1000 MHz. Radiated emission limits in these three bands are based on measurements employing an average detector. Other details are according ANSI C63.10. IRN 026 - Radiated electrical disturbance (V per m) Method 1 – 30 MHz – 1 GHz in SAR. IRN 026 - Radiated electrical disturbance (V per m) Method 2 – 1 - 18 GHz in SAR. IRN 026 - Radiated electrical disturbance (V per m) Method 3 – 18 - 26.5 GHz in SAR. 3.6.5 Notes • In the frequency range of 1 – 26 GHz the green trace is measured using a peak detector and the red trace is measured using an average detector. The top limit line represent the peak limit and the bottom limit represents the average limit Page 21 of 32

Report number: 180801587 003 Ver 3.00 3.6.6 Plots of the Radiated Spurious Emissions (BLE V5.0) 30 MHz to 1 GHz Vertical polarization 15.209/15.247 RBW : 100 kHz, Vertical Max Peak 65 60 55 50 45 40 Electrical Field (dBµV/m) Low ch 35 30 25 20 15 10 5 30 M 50 M 100 M 200 M 300 M 500 M 1G Frequency (Hz) 15.209/15.247 RBW : 100 kHz, Vertical Max Peak 65 60 55 50 45 40 Electrical Field (dBµV/m) Mid ch 35 30 25 20 15 10 5 30 M 50 M 100 M 200 M 300 M 500 M 1G Frequency (Hz) 15.209/15.247 RBW : 100 kHz, Vertical Max Peak 65 60 55 50 45 40 Electrical Field (dBµV/m) High ch 35 30 25 20 15 10 5 30 M 50 M 100 M 200 M 300 M 500 M 1G Frequency (Hz) Page 22 of 32

Report number: 180801587 003 Ver 3.00 30 MHz to 1 GHz Horizontal polarization 15.209/15.247 RBW : 100 kHz, Horizontal Max Peak 65 60 55 50 45 40 Electrical Field (dBµV/m) Low ch 35 30 25 20 15 10 5 30 M 50 M 100 M 200 M 300 M 500 M 1G Frequency (Hz) 15.209/15.247 RBW : 100 kHz, Horizontal Max Peak 65 60 55 50 45 40 Electrical Field (dBµV/m) Mid ch 35 30 25 20 15 10 5 30 M 50 M 100 M 200 M 300 M 500 M 1G Frequency (Hz) 15.209/15.247 RBW : 100 kHz, Horizontal Max Peak 65 60 55 50 45 40 Electrical Field (dBµV/m) High ch 35 30 25 20 15 10 5 30 M 50 M 100 M 200 M 300 M 500 M 1G Frequency (Hz) Page 23 of 32

Report number: 180801587 003 Ver 3.00 1 GHz to 18 GHz Vertical polarization Limit Average 1 - 18 GHz Limit Peak 1 - 18 GHz RBW : 1 MHz, Vertical Max Average RBW: 1 MHz, Vertical Max Peak 80 70 60 Electrical Field (dBµV/m) 50 Low ch 40 30 20 10 1G 2G 3G 5G 10 G 18 G Frequency (Hz) Limit Average 1 - 18 GHz Limit Peak 1 - 18 GHz RBW : 1 MHz, Vertical Max Average RBW: 1 MHz, Vertical Max Peak 80 70 60 Electrical Field (dBµV/m) 50 Mid ch 40 30 20 10 1G 2G 3G 5G 10 G 18 G Frequency (Hz) Limit Average 1 - 18 GHz Limit Peak 1 - 18 GHz RBW : 1 MHz, Vertical Max Average RBW: 1 MHz, Vertical Max Peak 80 70 60 Electrical Field (dBµV/m) 50 High ch 40 30 20 10 1G 2G 3G 5G 10 G 18 G Frequency (Hz) Page 24 of 32

Report number: 180801587 003 Ver 3.00 1 GHz to 18 GHz Horizontal polarization Limit Average 1 - 18 GHz Limit Peak 1 - 18 GHz RBW : 1 MHz, Horizontal Max Average RBW: 1 MHz, Horizontal Max Peak 80 70 60 Electrical Field (dBµV/m) 50 Low ch 40 30 20 10 1G 2G 3G 5G 10 G 18 G Frequency (Hz) Limit Average 1 - 18 GHz Limit Peak 1 - 18 GHz RBW : 1 MHz, Horizontal Max Average RBW: 1 MHz, Horizontal Max Peak 80 70 60 Electrical Field (dBµV/m) 50 Mid ch 40 30 20 10 1G 2G 3G 5G 10 G 18 G Frequency (Hz) Limit Average 1 - 18 GHz Limit Peak 1 - 18 GHz RBW : 1 MHz, Horizontal Max Average RBW: 1 MHz, Horizontal Max Peak 80 70 60 Electrical Field (dBµV/m) 50 High ch 40 30 20 10 1G 2G 3G 5G 10 G 18 G Frequency (Hz) Page 25 of 32

Report number: 180801587 003 Ver 3.00 18 GHz to 26 GHz Vertical polarization Limit Average 18 - 26 GHz Limit Peak 18 - 26 GHz RBW: 100 kHz, Vertical Max Average RBW: 100 kHz, Vertical Max Peak 85 80 75 70 65 60 Electrical Field (dBµV/m) High ch 55 50 45 40 35 30 25 18 G 19 G 20 G 21 G 22 G 23 G 24 G 25 G 26 G Frequency (Hz) Horizontal polarization Limit Average 18 - 26 GHz Limit Peak 18 - 26 GHz RBW: 100 kHz, Horizontal Max Average RBW : 100 kHz, Horizontal Max Peak 85 80 75 70 65 60 Electrical Field (dBµV/m) High ch 55 50 45 40 35 30 25 18 G 19 G 20 G 21 G 22 G 23 G 24 G 25 G 26 G Frequency (Hz) Page 26 of 32

Report number: 180801587 003 Ver 3.00 3.6.7 Plots of the Radiated Spurious Emissions (ANT) 30 MHz to 1 GHz Vertical polarization 15.209/15.247 RBW : 100 kHz, Vertical Max Peak 65 60 55 50 45 40 Electrical Field (dBµV/m) Low ch 35 30 25 20 15 10 5 30 M 50 M 100 M 200 M 300 M 500 M 1G Frequency (Hz) 15.209/15.247 RBW : 100 kHz, Vertical Max Peak 65 60 55 50 45 40 Electrical Field (dBµV/m) Mid ch 35 30 25 20 15 10 5 30 M 50 M 100 M 200 M 300 M 500 M 1G Frequency (Hz) 15.209/15.247 RBW : 100 kHz, Vertical Max Peak 65 60 55 50 45 40 Electrical Field (dBµV/m) High ch 35 30 25 20 15 10 5 30 M 50 M 100 M 200 M 300 M 500 M 1G Frequency (Hz) Page 27 of 32

Report number: 180801587 003 Ver 3.00 30 MHz to 1 GHz Horizontal polarization 15.209/15.247 RBW : 100 kHz, Horizontal Max Peak 65 60 55 50 45 40 Electrical Field (dBµV/m) Low ch 35 30 25 20 15 10 5 30 M 50 M 100 M 200 M 300 M 500 M 1G Frequency (Hz) 15.209/15.247 RBW : 100 kHz, Horizontal Max Peak 65 60 55 50 45 40 Electrical Field (dBµV/m) Mid ch 35 30 25 20 15 10 5 30 M 50 M 100 M 200 M 300 M 500 M 1G Frequency (Hz) 15.209/15.247 RBW : 100 kHz, Horizontal Max Peak 65 60 55 50 45 40 Electrical Field (dBµV/m) High ch 35 30 25 20 15 10 5 30 M 50 M 100 M 200 M 300 M 500 M 1G Frequency (Hz) Page 28 of 32

Report number: 180801587 003 Ver 3.00 1 GHz to 18 GHz Vertical polarization Limit Average 1 - 18 GHz Limit Peak 1 - 18 GHz RBW : 1 MHz, Vertical Max Average RBW: 1 MHz, Vertical Max Peak 80 70 60 Electrical Field (dBµV/m) 50 Low ch 40 30 20 10 1G 2G 3G 5G 10 G 18 G Frequency (Hz) Limit Average 1 - 18 GHz Limit Peak 1 - 18 GHz RBW : 1 MHz, Vertical Max Average RBW: 1 MHz, Vertical Max Peak 80 70 60 Electrical Field (dBµV/m) 50 1 Mid ch 40 30 20 10 1G 2G 3G 5G 10 G 18 G Frequency (Hz) Limit Average 1 - 18 GHz Limit Peak 1 - 18 GHz RBW : 1 MHz, Vertical Max Average RBW: 1 MHz, Vertical Max Peak 80 70 60 Electrical Field (dBµV/m) 50 High ch 40 30 20 10 1G 2G 3G 5G 10 G 18 G Frequency (Hz) Page 29 of 32

Report number: 180801587 003 Ver 3.00 1 GHz to 18 GHz Horizontal polarization Limit Average 1 - 18 GHz Limit Peak 1 - 18 GHz RBW : 1 MHz, Horizontal Max Average RBW: 1 MHz, Horizontal Max Peak 80 70 60 1 Electrical Field (dBµV/m) 50 Low ch 40 30 20 10 1G 2G 3G 5G 10 G 18 G Frequency (Hz) Limit Average 1 - 18 GHz Limit Peak 1 - 18 GHz RBW : 1 MHz, Horizontal Max Average RBW: 1 MHz, Horizontal Max Peak 80 70 60 Electrical Field (dBµV/m) 50 Mid ch 40 30 20 10 1G 2G 3G 5G 10 G 18 G Frequency (Hz) Limit Average 1 - 18 GHz Limit Peak 1 - 18 GHz RBW : 1 MHz, Horizontal Max Average RBW: 1 MHz, Horizontal Max Peak 80 70 60 Electrical Field (dBµV/m) 50 High ch 40 30 20 10 1G 2G 3G 5G 10 G 18 G Frequency (Hz) Page 30 of 32

Report number: 180801587 003 Ver 3.00 18 GHz to 26 GHz Vertical polarization Limit Average 18 - 26 GHz Limit Peak 18 - 26 GHz RBW: 100 kHz, Vertical Max Average RBW: 100 kHz, Vertical Max Peak 85 80 75 70 65 60 Electrical Field (dBµV/m) Low ch 55 50 45 40 35 30 25 18 G 19 G 20 G 21 G 22 G 23 G 24 G 25 G 26 G Frequency (Hz) 18 GHz to 26 GHz Horizontal polarization Limit Average 18 - 26 GHz Limit Peak 18 - 26 GHz RBW: 100 kHz, Horizontal Max Average RBW : 100 kHz, Horizontal Max Peak 85 80 75 70 65 60 Electrical Field (dBµV/m) Low ch 55 50 45 40 35 30 25 18 G 19 G 20 G 21 G 22 G 23 G 24 G 25 G 26 G Frequency (Hz) ANT Measured peaks Vertical 1 – 18 GHz Low channel Frequency Polarization Height Peak Average Peak Average Peak Average Limit Limit Difference Difference 7,206 GHz Vertical 3m 54,5 49,6 74 54 -19,5 dB -4,4 dB dBµV/m dBµV/m dBµV/m dBµV/m ANT Measured peaks Horizontal 1 – 18 GHz Middle channel Frequency Polarization Height Peak Average Peak Average Peak Average Limit Limit Difference Difference 7,32 GHz Vertical 1,5 m 47,9 40,1 74 54 -26,1 dB -13,9 dB dBµV/m dBµV/m dBµV/m dBµV/m Page 31 of 32

Report number: 180801587 003 Ver 3.00 3.6.8 Measurement Uncertainty Measurement uncertainty Radiated emissions below 1 GHz Horizontal polarization 30 – 200 MHz 4.5 dB 200 – 1000 MHz 3.6 dB Vertical polarization 30 – 200 MHz 5.4 dB 200 – 1000 MHz 4.6 dB Measurement uncertainty Radiated emissions above 1 GHz 1000- 18000 MHZ 5.7 dB 18000 – 26000 MHZ 3.9 dB Page 32 of 32


Document Created: 2019-06-16 20:18:32
Document Modified: 2019-06-16 20:18:32
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC