RF Exposure Evaluation (above 20 cm)

FCC ID: 2AAJCBR20

RF Exposure Info

Download: PDF
FCCID_4195463

D-PL-12076-01-03 Maximum Permissible Exposure (MPE) & Exposure evaluation Report identification number: 1-5475/17-01-139 Certification numbers and labeling requirements FCC ID 2AAJCBR20 IC number 24305-BR20 HVIN (Hardware Version Identification Number) MQB37W PMN (Product Marketing Name) MQB37W FVIN (Firmware Version Identification Number) -/- HMN (Host Marketing Name) -/- This test report is electronically signed and valid without handwriting signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Document authorized: DN: cn=Thomas Vogler, o=CTC advanced GmbH, ou=VOG-161125, email=thomas.vogler@ctcadvanced.com, c=DE Datum: 2018.09.26 12:37:37 +02'00' Thomas Vogler Lab Manager Radio Communications & EMC Page 1 of 3

EUT technologies: Technologies: Max. output: Max. antenna gain: Min. pathloss: FSK 67.25 dBµV/m @3 m AVG n/a -- (if applicable) @433.9 MHz = -28.11 dBm EIRP Prediction of MPE limit at given distance - FCC Equation from page 18 of OET Bulletin 65, Edition 97-01 S = PG / 4π R2 where: S = Power density P = Power input to the antenna G = Antenna gain R = Distance to the center of radiation of the antenna The table below is excerpted from Table 1B of 47 CFR 1.1310 titled “Limits for Maximum Permissible Exposure (MPE), Limits for General Population/Uncontrolled Exposure” Frequency Range (MHz) Power Density (mW/cm2) Averaging Time (minutes) 300 -1500 f/1500 30 1500 - 100000 1.0 30 where f = Frequency (MHz) Prediction: worst case < 1500 MHz Technology 433 MHz application PG Max EIRP < -20 dBm R Distance 20 cm S MPE limit for uncontrolled exposure 0.289 mW/cm2 Calculated Power density: < 0.00000034 mW/cm² This prediction demonstrates the following: The power density levels for FCC at a distance of 20 cm are below the maximum levels allowed by regulations. Page 2 of 3

Prediction of MPE limit at given distance - IC RSS-102, Issue 5, 2.5.2 RF exposure evaluation is required if the separation distance between the user and/or bystander and the device’s radiating element is greater than 20 cm, except when the device operates as follows: • below 20 MHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 1 W (adjusted for tune-up tolerance); • at or above 20 MHz and below 48 MHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 4.49/ƒ0.5W (adjusted for tune-up tolerance), where ƒ is in MHz; • at or above 48 MHz and below 300 MHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 0.6 W (adjusted for tune-up tolerance); • at or above 300 MHz and below 6 GHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 1.31 x 10-2 ƒ0.6834 W (adjusted for tune-up tolerance), where ƒ is in MHz; • at or above 6 GHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 5 W (adjusted for tune-up tolerance). Prediction: worst case Technology 433 MHz application PG Max EIRP -38.7 dBm Max EIRP 0.00017 mW Exclusion Limit from above 831 mW Conclusion: RF exposure evaluation is not required. For applications where minimum distance to radiating element is 20cm Annex C of RSS-102 should be filled out. Page 3 of 3


Document Created: 2018-09-26 12:37:37
Document Modified: 2018-09-26 12:37:37
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC