SAR_Appendix B_DAE Probe Cal. Certificate

FCC ID: 2AAED-R9861500D01

RF Exposure Info

Download: PDF
FCCID_4468759

Report No. :E5/2019/40005 Rev: 01 Page: 1 of 15 Appendix B — DAE & Probe Calibration Certificate Calibration Laboratory of & Schweizerischer Kalibrierdienst Schmid & Partner . Service suisse détatonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland S swiss Calibration Service Aceredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilteral Agreement for the recognition of calibration certificates Client SGS—TW (Auden) Certificate No: DAE4—547_Mar19 CALIBRATION CERTIFICATE Object DAE4 — SD 000 DO4 BM — SN: 547 Calibration procedure(s) QA CAL:06.v29 Calibration procedurefor the data acquisition electronics (DAE) Callbration date: March 22, 2019 This callbration certficate documents the traceabiity to national standards, which realize the physical units of measurements (S1) The measurements and the uncertainies with confidence probabilty are given on the following pages and are part of the certficate All allbrations have been conducted in the closed laboratory facilty: environment temperature (22 + 3)°C and humidity < 70% Galibration Equipment used (M&TE crtical for callbration) Primary Standards |1# Cal Date (Contficate No.) Scheduled Calibration Kelthley Multimeter Type 2001 | SN: 0810278 08—Sep—18 (No:23488) Sep—19 Secondary Standards | m# Check Date (in house) Scheduled Check Auto DAE Calbration Unit SE UWS 058 AA 1001 O7—Jan—19 (in house check) In house check: Jan—20 Galibrator Box V2.1 SE UMS 006 AA 1002 O7—Jan—19 (in house check) in house check: Jan—20 Name Function Signature Calibrated by: Dominique Steffen Laboratory Technician %\ Approved by: Sven Kihn Deputy Manager ‘V§ uw Issued: March 22, 2019 This callbration contficate shall not be reproduced except in full without writen approval of the laboratory. Certificate No: DAE4—547_Mart9 Page 1 of 5 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 20 days only. Bohseine . meesemuienncoiemet | amiubaiiinroon — deerhiLcAceeire > reraGae — This document is issued by the Company subject to its General Conditions of Service printed overleal, available on request or accessible at www.sgs.comterms and conditions.htm and for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms e—document/him. Altertion is rawn to the limitation of labilty, indemnification and Jurisclction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company‘s findings at the time of its intervertion only and within the Imits of Client‘s instructions, if any. The Company‘s sole responsibilty is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced excpt in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unfawul and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Tawan 24803/at i 2. M ts 4 4t & # @ (s % 3 134 3 6 MMoticttBieid PRar s1 1 (886—2) 2290—3279 1 (886—2) 2208—0488 www.twags.com | Member of SGS Group

Report No. :E5/2019/40005 Rev: 01 Page: 2 of 15 oig «en Calibration Laboratory of u7 Schweizerischer Kalibrierdienst Schmid & Partner m Service suisse détalonnage Engineering AG Servizio svizzero di taratura . . Zeugh?usstrasse ?3 8004 Zurich, Switzerland Ajs ///_%~ Swiss i Calibration i i Service Aceredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary DAE data acquisition electronics Connector angle information used in DASY system to align probe sensor X to the robot coordinate system. Methods Applied and Interpretation of Parameters * DC Voltage Measurement: Calibration Factor assessed for use in DASY system by comparison with a calibrated instrument traceable to national standards. The figure given corresponds to the full scale range of the voltmeterin the respective range. * Connector angle: The angle of the connectoris assessed measuring the angle mechanically by a tool inserted. Uncertainty is not required. * The following parameters as documented in the Appendix contain technical information as a result from the performance test and require no uncertainty. * DC Voltage Measurement Linearity: Verification of the Linearity at +10% and —10%of the nominal calibration voltage. Influenceof offset voltage is included in this measurement. * Common mode sensitivity: Influence of a positive or negative common mode voltage on the differential measurement. * Channel separation: Influence of a voltage on the neighbor channels not subject to an input voltage. «_ AD Converter Values with inputs shorted: Values on the internal AD converter corresponding to zero input voltage * Input Offset Measurement: Output voltage and statistical results over a large number of zero voltage measurements. * Input Offset Current: Typical value for information; Maximum channelinput offset current, not considering the input resistance. * Input resistance: Typical value forinformation: DAE input resistance at the connector, during internal auto—zeroing and during measurement. «_ Low Battery Alarm Voltage: Typical value for information. Below this voltage, a battery alarm signal is generated. «+ Power consumption: Typical value for information. Supply currents in various operating modes. Certificate No: DAE4—547_Mar19 Page 2 of 5 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. borstm® . ieemetnzim— Eeieaiir roon » dEhLiAcereite > neieie — This document is issued by the Company subject to its General Conditions of Service printed overleal, available on request or accessible at www.sgs.comterms and conditions.htm and for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms e—document/htm. Attention is drawn to the limitation of labilty, indemnification and jurisdiction issues detined therein. Any holder of this document is advised that information contained hereon reflects the Company‘s findings at the time of its intervertion only and within the Imits of Client‘s instructions, f any. The Company‘s sole responsibilty is to its Client and this document doss not exonerate paties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawlul and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Tawan 24803/at i 2. M ts 4 4t & # @ (s % 3 134 3 6 MMoticttBieid PRar s1 t (B86—2) 2200.s279 1 (Bee—2) 2208—0488 www.tw.egs.com | Member of SGS Group

Report No. :E5/2019/40005 Rev: 01 Page: 3 of 15 DC Voltage Measurement A/D — Converter Resolution nominal High Range: 1LSB = 6ApV , full range= —100...+300 mV Low Range: 1LSB= 61nV , full range= ~1. +3mV DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: see Calibration Factors X Y 2 High Range 403.235 + 0.02% (k=2) 408.136 £ 0.02%(k=2) 402.783 + 0.02% (k=2) Low Range 3.95448 + 1.50% (k=2) 3.90479 + 1.50% (k=2) 3.96245 £ 1.50%(k=2) Connector Angle Connector Angle to be used in DASY system $h6"%1° Certificate No: DAE4—547_Mar19 Page 3 of 5 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Eokemt ) Imeenienist—iient | EHitR ERENX — AEchi—AciEmere > oeent — This document is Issued by the Company subject to its General Condiions of Service printed overleaf, available on request or accessible at www.sas.com/terms and_ conditions.him and for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sqs.com/terms e—document.him. Aftention is drawn to the limitation of liabiltty, indemnffication and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company‘s findings at the time of its intervention only and within the limits of Client‘s instructions, if any. The Company‘s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduiced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawiul and offenders may be prosectited to the fullest extent of the law SGS Taiwan Ltd. No.134, Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/4 2b i 3MAE #r t& K M B x 1% 134 6 MBeliePRcic Mss c 1 (886—2) 2200—3279 1 (886—2) 2208—0488 wwrnw.sgs.com | Memberof SGS Group

Report No. :E5/2019/40005 Rev: 01 Page: 4 of 15 Appendix (Additional assessments outside the scope of SCS0108) 1. DC Voltage Linearity High Range Reading (aV) Difference (2V) Error (%) Channel X + Input 199995.43 141 0.00 ChannelX + Input 20002.84 1.52 0.01 ChannelX — Input +19996.87 4.76 —0.02 Channel Y + Input 199993.66 0.02 0.00 ChannelY + Input 19999.34 —2.02 —0.01 ChannelY — Input —20003.96 —2.39 0.01 Channel Z + Input 199994.47 1.04 0.00 Channel Z + Input 20002.60 1.36 0.01 ChannelZ — Input —20001.47 0.29 —0.00 Low Range Reading (uV) Difference (1V) Error (%) ChannelX + Input 2000.59 —0.23 —0.01 Channel X + Input 201.16 —0.10 —0.05 Channel X — Input —199.09 —0.45 0.23 Channel Y + Input 2000.65 —0.10 —0.01 Channel Y + Input 200.83 —0.37 —0.18 Channel Y — Input —199.37 —0.70 0.35 ChannelZ + Input 2000.46 —0.35 —0.02 Channel Z + Input 199.75 —1.50 —0.75 ChannelZ — Input —200.47 —1.80 0.90 2. Common mode sensitivity DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 see Common mode High Range Low Range Input Voltage (mV) Average Reading (1V) Average Reading (1V) Channel X 200 —3.65 —5.24 —200 5.24 3.62 Channel Y 200 —0.39 +1.02 —200 0.24 —0.55 ChannelZ 200 5.61 5.22 —200 —7.68 811 3. Channel separation DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 see Input Voltage (mV) Channel X (@V) Channel Y (V) Channel Z (uV) Channel X 200 * 3.67 —2.18 Channel Y 200 9.88 — 4.13 ChannelZ 200 4.62 8.17 — Certficate No: DAE4—547_Mart9 Page 4 of 5 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 20 days only. Bohseine . meesemuienncoiemet | amiubaiiinroon — deerhiLcAceeire > reraGae — This document is issued by the Company subject to its General Conditions of Service printed overleal, available on request or accessible at www.sgs.comterms and conditions.htm and for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms e—document/him. Altertion is rawn to the limitation of labilty, indemnification and Jurisclction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company‘s findings at the time of its intervertion only and within the Imits of Client‘s instructions, if any. The Company‘s sole responsibilty is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced excpt in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unfawul and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Tawan 24803/at i 2. M ts 4 4t & # @ (s % 3 134 3 6 MMoticttBieid PRar s1 1 (B86—2) 2200.s279 1 (88e—2) 22o8—0488 wwwetw.ags.com | Member of SGS Group

Report No. :E5/2019/40005 Rev: 01 Page: 5 of 15 4. AD—Converter Values with inputs shorted DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 see High Range (LSB) Low Range (LSB) Channel X 16357 14727 Channel Y 16459 15185 ChannelZ 16084 17210 5. Input Offset Measurement DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Input 10M@ Average (uV) min. Offset (V) max. Offset (uv) 5* [(’:“I’;a‘ic‘“ ChannelX —1.59 —2.60 —0.90 0.32 ChannelY 0.54 —0.42 1.60 0.34 Channel2 0.95 —0.46 2.89 0.59 6. Input Offset Current Nominal Input circuitry offset current on all channels: <25fA 7. Input Resistance (Typical values for information) Zeroing (kOhm) Measuring (MOhm) Channel X 200 200 ChannelY 200 200 ChannelZ 200 200 8. Low Battery Alarm Voltage (Typical values for information) Typical values Alarm Level (VDC) Supply (+ Vee) +7.9 Supply (— Vee) 7.6 9. Power Consumption (Typical values for information) Typical values Switched off (mA) Stand by (mA) Transmitting (mA) Supply (+ Vee) +0.01 +6 +14 Supply (— Vee) ~0.01 —8 —9 Certficate No: DAE4—547_Mar19 Page 5 of 5 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. borstm® . ie emet nzim — Eeieaiir roon » d EhLiA cereite > neieie — This document is issued by the Company subject to its General Conditions of Service printed overleal, available on request or accessible at www.sgs.comterms and conditions.htm and for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms e—document/htm, Attertion is drewn to the limitation of labilty, indemnification and Jurisclction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company‘s findings at the time of its intervertion only and within the Imits of Client‘s instructions, f any. The Company‘s sole responsibilty is to its Client and this document doss not exonerate paties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawlul and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Tawan 24803/at i 2. M ts 4 4t & # @ (s % 3 134 3 6 MMoticttBieid PRar s1 1 (B86—2) 2200.s279 1 (88e—2) 22o8—0488 wwwetw.ags.com | Member of SGS Group

Report No. :E5/2019/40005 Rev: 01 Page: 6 of 15 Calibration Laboratory of «n & Schweizerischer Kalibrierdienst Schmid & Partner . Service suisse d‘étalonnage Engineering AG T en g Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland ”"'/,fi. w Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Client SGS—TW (Auden) Certificate No: EX3—7466_Feb19 CALIBRATION CERTIFICATE | Object EXSDV4 — SN:7466 Calibration procedure(s) QA CAL—01.v9, QA CAL—12.v9, QA CAL—14.v5, QA CAL—23.v5, QA CAL—25.v7 Calibration procedure for dosimetric E—field probes Calibration date February 4, 2019 This calbration certficate documents the traceabilty to national standards, which realizethe physical units of measurements (81) The measurements and the uncertainties with confidence probabilty are given on the following pages and are part of the certifcate. All calibrations have been conducted in the closed laboratory facilty: environment temperature (22 + 3)°C and humidty < 70% Calibration Equipment used (M&TE critical for calibration) Primary Standards iD Cal Date (Certiicate No.) Scheduled Calibration Power meter NRP SN: 104778 04—Apr—18 (No. 217—02672702673) Apr—19 Power sensor NRP—281 SN: 103244 04—Apr—18 (No. 217—02672) Apr—19 Power sensor NRP—281 SN: 103245 04—Apr—18 (No. 217—02673) Apr—19 Reference 20 dB Attenuator SN: S5277 (200) 04—Apr—18 (No. 217—02682) Apr—19 DAE4 SN: 660 19—Dec—18 (No. DAE4—660_Dec18) Dec—19 Reference Probe ESSDV2 SN: 3013 31—Dec—18 (No. ES3—3013_Dec18) Dec—19 Secondary Standards iD Check Date (in house) Scheduled Check Power meter E44198 SN: GB41203874 06—Apr—16 (in house check Jun—18) in house check: Jun—20 Power sensor E4412A SN: MY4 1408087 06—Apr—16 (in house check Jun—18) in house check: Jun—20 Power sensor E4412A SN: 000110210 06—Apr—16 (in house check Jun—18) In house check: Jun—20 RF generator HP 8648C SN: US3642U01700 (4—Aug—99 (in house check Jun—18) in house check: Jun—20 Network Analyzer E8358A SN: US41080477 31—Mar—14 (in house check Oct—18) In house check: Oct—19 Name Function Signature Calibrated by: Jeton Kastral Laboratory Technician fl I Approved by: Katie Pokovie Technical Manager /m: Issued: February 4, 2019 This callbration certficate shall not be reproduced except in full without written approval of the laboratory. Certificate No: EX3—7466_Feb19 Page 1 of 10 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Eokhemt ) Imecsenirnisc—iksent | ENNREERENX — AHEcnichAdEarre | oSb— This document is Issued by the Company subject to its General Condiions of Service printed overleaf, available on request or accessible at www.sqs.com/terms_and conditions.him and for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sqs.com/terms e—document.him, Atention is drawn to the limtation of liabilty, indemnification and jurisdiction Issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company‘s findings at the time of ts intervention only and within the limits of Client‘s instructions, if any. The Company‘s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduiced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearanceof this document is unlawful and offenders may be prosectited to the fullest extent of the law SGS Taiwan Ltd. No.134, Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/% 2t ®JB Ar 6& % 8 & # 15 134 & 6 MBeliePRcic Mss c 1 (886—2) 2200—3279 1 (886—2) 2208—0488 wwrnw.sgs.com | Memberof SGS Group

Report No. :E5/2019/40005 Rev: 01 Page: 7 of 15 Calibration Laboratory of G SchweizerischerKalibrierdienst Schmid & Partner g Service suisse d‘étalonnage Engineering AG g. Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Glossary: TSL tissue simulating liquid NORMx,y,z sensitivity in free space ConvF sensitivity in TSL / NORMx,y,z DCP diode compression point CF crest factor (1/duty_cycle) of the RF signal A, B, C, D modulation dependent linearization parameters Polarization «p i rotation around probe axis Polarization 8 8 rotation around an axis that is in the plane normal to probe axis (at measurement center) i.e., 8 = 0 is normal to probe axis Connector Angle information used in DASY system to align probe sensor X to therobot coordinatesystem Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques®, June 2013 b) IEC 62209—1, ", "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand— held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)®, July 2016 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)*, March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Methods Applied and Interpretation of Parameters: NORMx,y,z: Assessed for E—field polarization 8 = 0 (f < 900 MHz in TEM—cell; f> 1800 MHz: R22 waveguide}. NORMx,y,z are only intermediate values, i.e., the uncertainties of NORMx,y,z does not affect the E*—field uncertainty inside TSL (see below ConvF). NORM(Mx.y,z = NORMx,y,z * frequency_response (see Frequency Response Chart). This linearization is implemented in DASY4 software versions later than 4.2. The uncertainty of the frequency response is included in the stated uncertainty of ConvF. DCPx.y,z: DCP are numerical linearization parameters assessed based on the data of power sweep with CW signal (no uncertainty required). DCP does not depend on frequency nor media. PAR: PAR is the Peak to Average Ratio that is not calibrated but determined based on the signal characteristics Axy.z: Bxy,z; Coy.z: Dxy,z; VRxy,z: A, B, C, D are numerical linearization parameters assessed based on the data of power sweep for specific modulation signal. The parameters do not depend on frequency nor media. VR is the maximum calibration range expressed in RMS voltage across the diode. ConvF and Boundary Effect Parameters: Assessed in flat phantom using E—field (or Temperature Transfer Standard for f < 800 MHz) and inside waveguide using analytical field distributions based on power measurements for f > 800 MHz. The same setups are used for assessment of the parameters applied for boundary compensation (alpha, depth) of which typical uncertainty values are given. These parameters are used in DASY4 software to improve probe accuracy close to the boundary. The sensitivity in TSL corresponds to NORMx,y,z * ConvF whereby the uncertainty corresponds to that given for ConvF.A frequency dependent ConvF is used in DASY version 4.4 and higher which allows extending the validity from + 50 MHz to + 100 MHz. Sphericalisotropy (3D deviation from isotropy): in a field of low gradients realized using a flat phantom exposed by a patch antenna. Sensor Offset: The sensoroffset corresponds to the offset of virtual measurement center from the probe tip (on probe axis}. No tolerance required. Connector Angle: The angle is assessed using the information gained by determining the NORMx (no uncertainty required). Certificate No: EX3—7406_Feb19 Page 2 of 10 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Eokhemt ) Imecsenirnisc—iksent | ENNREERENX — AHEcnichAdEarre | oSb— This document is Issued by the Company subject to its General Condiions of Service printed overleaf, available on request or accessible at www.sqs.com/terms_and conditions.him and for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sqs.com/terms_e—documenthim Aftention is drawn to the limitation of liabilty, indemnification and jurisdiction issues detined therein. Any holder of this document is advised that information contained hereon reflects the Company‘s findings at the time of ts intervention only and within the limits of Client‘s instructions, if any. The Company‘s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduiced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearanceof this document is unlawful and offenders may be prosectited to the fullest extent of the law SGS Taiwan Ltd. No.134, Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/% 2t ®JB Ar 6& % 8 & # 15 134 & 6 MBeliePRcic Mss c 1 (886—2) 2200—3279 1 (886—2) 2208—0488 wwrnw.sgs.com Member of SGS Group

Report No. :E5/2019/40005 Rev: 01 Page : 8 of 15 EX3DV4 — SN :7466 February 4, 2019 DASY/EASY — Parameters of Probe: EX3DV4 — SN:7466 Basic Calibration Parameters Sensor X Sensor Y Sensor Z Unc (k=2) Norm (pVi(Vim)?)" 047 0.40 0.62 £10.1% DCP (mV)" 98.2 99.6 _ 98.8 Calibration Results for Modulation Response Uib Communication System Name A B c p VR Max Unc® dB dByuV dB mV dev. (k=2) 0 Cw x 0.0 0.0 1.0 0.00 1526 130% £47% Y 0.0 0.0 10 138.6 y 0.0 0.0 10 155.1 The reported uncertainty of measurementis stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. * The uncertainties of Norm X.Y,Z do not affect the E*—field uncertainty inside TL (see Pages 5 and 6) * Numerical inearization parameter: uncertainty not required. © Uncertainty is determined using the max. deviation from linear response applying rectangular distribution and is expressed for the square of the field value Certificate No: EX3—7466_Feb19 Page 3 of 10 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Eokhemt ) Imecsenirnisc—iksent | ENNREERENX — AHEcnichAdEarre | oSb— This document is Issued by the Company subject to its General Condiions of Service printed overleaf, available on request or accessible at www.sqs.com/terms_and conditions.him and for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sqs.com/terms_e—documenthim Aftention is drawn to the limitation of liabilty, indemnification and jurisdiction issues detined therein. Any holder of this document is advised that information contained hereon reflects the Company‘s findings at the time of ts intervention only and within the limits of Client‘s instructions, if any. The Company‘s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduiced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearanceof this document is unlawful and offenders may be prosectited to the fullest extent of the law SGS Taiwan Ltd. No.134, Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/% 2t ®JB Ar 6& % 8 & # 15 134 & 6 MBeliePRcic Mss c 1 (886—2) 2200—3279 t (886—2) 2208—0488 www.w.sgs.com Member of SGS Group

Report No. :E5/2019/40005 Rev: 01 Page: 9 of 15 EX3DV4— SN:7466 February 4, 2019 DASY/EASY — Parameters of Probe: EX3DV4 — SN:7466 Other Probe Parameters Sensor Arrangement Triangular Connector Angle (°) —6.8 Mechanical Surface Detection Mode enabled Optical Surface Detection Mode disabled Probe Overall Length 337 mm Probe Body Diameter 10 mm Tip Length 9 mm Tip Diameter 2.5 mm Probe Tip to Sensor X Calibration Point 1 mm Probe Tip to Sensor Y Calibration Point 1 mm Probe Tip to Sensor Z Calibration Point 1 mm Recommended Measurement Distance from Surface 1.4 mm Certificate No: EX3—7466_Feb19 Page 4 of 10 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Eokhemt ) Imecsenirnisc—iksent | ENNREERENX — AHEcnichAdEarre | oSb— This document is Issued by the Company subject to its General Condiions of Service printed overleaf, available on request or accessible at www.sqs.com/terms_and conditions.him and for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sqs.com/terms_e—documenthim Aftention is drawn to the limitation of liabilty, indemnification and jurisdiction issues detined therein. Any holder of this document is advised that information contained hereon reflects the Company‘s findings at the time of ts intervention only and within the limits of Client‘s instructions, if any. The Company‘s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduiced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearanceof this document is unlawful and offenders may be prosectited to the fullest extent of the law SGS Taiwan Ltd. No.134, Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/% 2t ®JB Ar 6& % 8 & # 15 134 & 6 MBeliePRcic Mss c 1 (886—2) 2200—3279 f (886—2) 2208—0488 www.tw.sgs.com Member of SGS Group

Report No. :E5/2019/40005 Rev: 01 Page: 10 of 15 EX3DV4— SN:7466 February 4, 2019 DASY/EASY — Parameters of Probe: EX3DV4 — SN:7466 Calibration Parameter Determined in Head Tissue Simulating Media Relative Conductivity Depth Unc £(MbHz)°_|_Permittivity" (Sim)" ConvFX ConvEY| ConvEZ Alpha® |__(mm) (k=2) 600 42.7 0.88 10.73 10.73 10.73 0.00 1.00 £13.3 % 750 41.9 0.89 10.45 1045 1045 0.46 0.85 +12.0 % 835 41.5 0.90 10.15 10.15 10.15 0.27 1.18 £12.0 % 900 41.5 0.97 9.87 9.87 9.87 0.33 1.04 £12.0 % 1750 40.1 1.37 8.99 8.99 8.99 0.33 0.86 £12.0 % 1900 40.0 1.40 8.67 8.67 8.67 0.36 0.85 +12.0 % 2000 40.0 1.40 8.53 8.53 8.53 0.35 0.85 £12.0 % 2300 39.5 1.67 8.26 8.26 8.26 0.34 0.86 £120% 2450 39.2 1.80 7.66 7.66 7.66 0.38 0.90 +12.0 % 2600 39.0 1.96 743 743 743 0.27 1.30 £12.0 % 3300 38.2 2.71 7.05 7.05 7.05 0.30 115 £181% 3500 37.9 2.91 6.98 6.98 6.98 0.30 120 £131% 3700 37.7 3.12 6.94 6.94 6.94 0.30 1.20 £13.1 % 3900 37.5 3.32 6.71 6.71 671 0.25 1.60 £13.1% 5200 36.0 4.66 5.56 5.56 5.56 0.40 1.80 £13.1% 5300 35.9 4.76 541 541 5.41 0.40 180 £131% 5600. 35.5 5.07 4.88 4.88 4.88 0.40 1.80 £13.1 % 5800. 35.3 5.27 5.06 5.06 i 5.06 0.40 1.80 £131% © Frequency validty above 300 MHz of + 100 MHz only applies for DASY v4.4 and higher (see Page 2), alse it is restricted to + 50 MHz. The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for the inicated frequency band. Frequency validity below 300 MHz is + 10, 25, 40, 50 and 70 MHz for ConvF assessments at 30, 64, 128, 150 and 220 MHz respectively. Validity of Convr assessed at 8 MHz is 4—9 MHz, and ConvF assessed at 13 MHz is 9—19 MHz. Above 5 GHz frequency validity can be extended to + 110 MHz. " At frequencies below 3 GHz, the validity oftissue parameters (c and a) can be relaed to + 10% if liquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validily of tssue parameters ( and a)is restricted to + 5%. The uncertainty is the RSS of the Convuncertainty for indicated targettissue parameters * Alpha/Depth are determined during calibration, SPEAG warrants that the remaining deviation due to the boundary effect after compensation is always less than + 1% for frequencies below 3 GHz and below + 2% for frequencies between 3—6 GHz at any distancelarger than half the probetip diameter from the boundary: Certificale No: EX3—7466_Feb19 Page 5 of 10 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Eokhemt ) Imecsenirnisc—iksent | ENNREERENX — AHEcnichAdEarre | oSb— This document is Issued by the Company subject to its General Condiions of Service printed overleaf, available on request or accessible at www.sqs.com/terms_and conditions.him and for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sqs.com/terms e—document.him, Atention is drawn to the limtation of liabilty, indemnification and jurisdiction Issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company‘s findings at the time of ts intervention only and within the limits of Client‘s instructions, if any. The Company‘s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduiced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearanceof this document is unlawful and offenders may be prosectited to the fullest extent of the law SGS Taiwan Ltd. No.134, Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/% 2t ®JB Ar 6& % 8 & # 15 134 & 6 MBeliePRcic Mss c 1 (886—2) 2200—3279 1 (886—2) 2208—0488 wwrnw.sgs.com | Memberof SGS Group

Report No. :E5/2019/40005 Rev: 01 Page: 11 of 15 EX3DV4~ SN:7466 February 4, 2019 DASY/EASY — Parameters of Probe: EX3DV4 — SN:7466 Calibration Parameter Determined in Body Tissue Simulating Media Relative Conductivity Depth ° Une £(MHz)® |_Permittivity" (Sim)" ConvFX ConvFY ConvFZ Alpha® |__({mm) (k=2) 600 56.1 0.95 10.86 10.86 10.86 0.00 1.00 £13.3 % 750 55.5 0.96 10.49 10.49 10.49 0.30 1.08 2120 % 835 55.2 0.97 10.04 10.04 10.04 0.31 1.09 +120 % 900 55.0 1.05 9.94 9.94 9.94 0.31 1.04 £12.0 % 1750 534 149 8.48 8.48 848 0.36 0.87 +120 % 1900 53.3 1.52 8.04 8.04 8.04 0.44 0.86 £12.0 % 2000 53.3 1.52 7.94 7.94 7.94 0.30 1.15 £12.0 % 2300 52.9 1.81 7.84 7.84 7.84 0.40 0.92 £12.0 % 2450 52.7 1.95 7m 7m 77 0.44 0.90 £12.0 % 2600 52.5 216 747 7.a7 7.47 0.41 0.96 +12.0 % 3300 51.6 3.08 6.86 6.86 6.86 0.26 1.20 £13.1% 3500 51.3 3.31 6.69 6.69 6.69 0.25 1.25 £13.1% 3700 51.0 3.55 6.58 6.58 6.58 0.30 1.25 £18.1 % 3900 51.2 3.78 612 6.12 6.12 0.25 1.60 £13.1 % 5200 49.0 5.30 4.95 4.95 4.95 0.50 1.90 £13.1% 5300. 48.9 542 4.80 4.80 4.80 0.50 1.90. £13.1 % 5600 48.5 5.77 4.22 4.22 4.22 0.50 1.90 £13.1 % 5800 48.2 6.00 4.38 4.38 4.38 0.50 1.90 £13.1 % © Frequency validty above 300 MHz of + 100 MHz only applies for DASY v4.4 and higher (see Page 2), else it is restricted to + 50 MHz. The uncertainty is the RSS of the Conv uncertainty at calibration frequency and the uncertainty for the indicated frequency band. Frequency validty below 300 MHz is + 10, 25, 40, 50 and 70 MHz for Conv assessments at 30, 64, 128, 150 and 220 Mz respectively. Validity of Conve assessed at 6 MHz is 4—9 MHz, and Convassessed at 13 MHz is 9—19 MHz. Above 5 GHz frequency valdity can be extended to + 110 MHz. " Atfrequencies below 3 GHz, the validity of tissue parameters (s and a) can be relaxed to + 10% if liquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validity of tssue parameters (c and a)is restricted to + 5%. The uncertainty is the RSS of the ConvF uncertainty for indicated target tissue parameters 5 AlphafDepth are determined during calibration. SPEAG warrants that the remaining deviation due to the boundary effect after compensation is always less than :+ 1% for frequencies below 3 GHz. and below + 2% for frequencies between 3—6 GHz at any distancelarger than half the probe tip diameter from the boundary Certificate No: EX3—7466_Feb19 Page 6 of 10 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Eokhemt ) Imecsenirnisc—iksent | ENNREERENX — AHEcnichAdEarre | oSb— This document is Issued by the Company subject to its General Condiions of Service printed overleaf, available on request or accessible at www.sqs.com/terms_and conditions.him and for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sqs.com/terms e—document.him, Atention is drawn to the limtation of liabilty, indemnification and jurisdiction Issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company‘s findings at the time of ts intervention only and within the limits of Client‘s instructions, if any. The Company‘s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduiced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearanceof this document is unlawful and offenders may be prosectited to the fullest extent of the law SGS Taiwan Ltd. No.134, Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/% 2t ®JB Ar 6& % 8 & # 15 134 & 6 MBeliePRcic Mss c 1 (886—2) 2200—3279 1 (886—2) 2208—0488 wwrnw.sgs.com | Memberof SGS Group

Report No. :E5/2019/40005 Rev: 01 Page: 12 of 15 EX3DV4— SN:7466 February 4, 2019 Frequency Response of E—Field (TEM—Cell:ifi110 EXX, Waveguide: R22) Frequency response (normalized Le] TEM Uncertainty of Frequency Response of E—field: 2 6.3%(k=2) Certificate No: EX3—7466_Feb19 Page 7 of 10 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Eokhemt ) Imecsenirnisc—iksent | ENNREERENX — AHEcnichAdEarre | oSb— This document is Issued by the Company subject to its General Condiions of Service printed overleaf, available on request or accessible at www.sqs.com/terms_and conditions.him and for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sqs.com/terms e—document.him, Atention is drawn to the limtation of liabilty, indemnification and jurisdiction Issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company‘s findings at the time of ts intervention only and within the limits of Client‘s instructions, if any. The Company‘s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduiced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearanceof this document is unlawful and offenders may be prosectited to the fullest extent of the law SGS Taiwan Ltd. No.134, Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/% 2t ®JB Ar 6& % 8 & # 15 134 & 6 MBeliePRcic Mss c 1 (886—2) 2200—3279 1 (886—2) 2208—0488 wwrnw.sgs.com | Memberof SGS Group

Report No. :E5/2019/40005 Rev: 01 Page: 13 of 15 EX3DV4~ SN:7466 February 4, 2019 Receiving Pattern (¢), 8 = 0° £=600 MHz,TEM £=1800 MHz,R22 as4. & & 3 001 & 54. Uncertainty of Axial Isotropy Assessment: £ 0.5% (k=2) Certificate No: EX3—7466_Feb19 Page 8 of 10 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Eokhemt ) Imecsenirnisc—iksent | ENNREERENX — AHEcnichAdEarre | oSb— This document is Issued by the Company subject to its General Condiions of Service printed overleaf, available on request or accessible at www.sqs.com/terms_and conditions.him and for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sqs.com/terms e—document.him, Atention is drawn to the limtation of liabilty, indemnification and jurisdiction Issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company‘s findings at the time of ts intervention only and within the limits of Client‘s instructions, if any. The Company‘s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduiced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearanceof this document is unlawful and offenders may be prosectited to the fullest extent of the law SGS Taiwan Ltd. No.134, Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/% 2t ®JB Ar 6& % 8 & # 15 134 & 6 MBeliePRcic Mss c 1 (886—2) 2200—3279 1 (886—2) 2208—0488 wwrnw.sgs.com | Memberof SGS Group

Report No. :E5/2019/40005 Rev: 01 Page: 14 of 15 EX3DV4~ SN:7466 February 4, 2019 Dynamic Range f(SARneaq) (TEM cell , feyy;= 1900 MHz) Input Signal [uV) 10 10‘ 10° SAR [mWicm3] not compensated Ce] compensated to Error [dB] T T 103 102 101 109 10! 102 103 SAR [mW/cm3] not compensated compensated Uncertainty of Linearity Assessment: £ 0.6% (k=2) Certificate No: EX3—7466_Feb19 Page 9 of 10 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Eokhemt ) Imecsenirnisc—iksent | ENNREERENX — AHEcnichAdEarre | oSb— This document is Issued by the Company subject to its General Condiions of Service printed overleaf, available on request or accessible at www.sqs.com/terms_and conditions.him and for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sqs.com/terms e—document.him, Atention is drawn to the limtation of liabilty, indemnification and jurisdiction Issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company‘s findings at the time of ts intervention only and within the limits of Client‘s instructions, if any. The Company‘s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduiced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearanceof this document is unlawful and offenders may be prosectited to the fullest extent of the law SGS Talwan Ltd. No.134, Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/% 2t ®JB Ar 6& % 8 & # 15 134 & 6 MBeiePRcic fkk c 1 (886—2) 2200—3279 1 (886—2) 2208—0488 wwrnw.sgs.com | Memberof SGS Group

Report No. :E5/2019/40005 Rev: 01 Page: 15 of 15 EX3DV4— SN:7466 February 4, 2019 Conversion Factor Assessment 1= 835 MHz,WGLS R9 (H_conv?) 1= 1900 MHz.WGLS R22 (H_conve) 2 me Deviation from Isotropy in Liquid Error (¢, 8), £= 900 MHz Devation 10 —08 —06 —04 —02 00 02 o4 06 o8 10 Uncertainty of Spherical Isotropy Assessment: £ 2.6% (k=2) Certficate No: EX3—7466_Feb19 Page 10 of 10 — End of report — Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Eoihent | Imdemhieenisc—ksent : EHIEREREIX — AHEAEAAIEGRT — Todtantl — This document is Issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sqs.com/terms and conditions htm and for electronic format documents, subject to Terms and Conditions for Electronic Documents at www sqs.com/ferms e—documenthim Aftention is drawn to the limitation of liability, indemnffication and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company‘s findings at the time of ts intervention only and within the limits of Client‘s instructions, if any. The Company‘s sole responsibility is to its Client and this docuimentdoes not exonerate partes to a transaction from exercising all their rights and obligations under the transaction documents. This docuimentcannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearanceof this docuiment is unlawul and offenders may be prosectited to the fullest extent of the law SGS Talwan Ltd. No.134, Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan 24803/%r 2t# ®JtE Ar 6& % F & # 15 134 6 MBeiePRcic fkk c 1 (886—2) 2200—3279 1 (886—2) 2208—0488 wwrnw.sgs.com | Member of SGS Group


Document Created: 2019-10-08 10:24:21
Document Modified: 2019-10-08 10:24:21
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC