User Manual 1

FCC ID: 2AA98-MEDIUM5C

Users Manual

Download: PDF
FCCID_4237500

                                                               Visteon Electronics Germany GmbH
                                                               Visteonstrasse 4-10                        +49 (0) 721-4766-1900
                                                               D-50170 Kerpen                             +49 (0) 721-4766-1263
                                                               Germany                                    certger@visteon.com
                                                                                                          www.visteon.com




          Installation of MEDIUM 5C and COLOUR 5C


          Fixing of the Device into the Vehicle:

          The MQB Cluster is professionally OEM-installed in the instrument panel of the vehicle
          behind the steering wheel.

          Once fixed; all connectivity to other units must be done via the CAN-bus (see Electrical
          Connections section under the Factory Process).

          Mounting of the IC
          IC will be fixed by clipped by 4 mounting clips of the front frame unit into the instrument panel
          of the vehicle. Additionally the device is fixed by 2 screws to the instrument panel. Use torque
          wrenches to ensure the correct tightening of all screws.
          After the mounting of the IC into instrument panel a corresponding vehicle bezel is clipped
          onto the IC front frame.
          S. Figure 1.


          The Factory Process
          Handling
                    Work with clean gloves (changed on a regular basis).
                    Unpack the IC as close as possible to the production line.
                    Do not stack, hit or scratch in any way the unpacked IC.
                    Do not push or pull on any connectors during the placement and fixing of the device.
                     Instead, push on the sturdy sides or edges of the casing while positioning and fixing the
                     device.
                    Do not scratch, tear or remove the pre-fitted labels.
                    While installing cables, make sure that no cable is pinched or damaged at any point
                     along its length.
                    When fixed, ensure that the heat sink portion of the device’s casing is free and not
                     blocked by any obstruction.
                    If any IC is dropped or falls down, it must be scrapped.

          Electrical Connections

                                                                              1
Visteon Electronics Germany GmbH
Sitz der Gesellschaft / Place of Business: Kerpen        Geschäftsführung / Management Board      Bank: Bank of America Merrill Lynch
Registergericht / Registration Office: Köln, HRB 78269   Jens Tillner                             Konto Nr. / Account No: 20569017
USt-IDNR. / VAT ID: DE 294 194 802                       Jochen Ladwig                            IBAN: DE96 5001 0900 0020 5690 17
Steuer Nr. / Tax No: 203/5788/1299                                                                SWIFT / BIC code: BOFADEFX


                                                                 Visteon Electronics Germany GmbH            +49 (0) 721-4766-1900
                                                                 Visteonstrasse 4-10                         +49 (0) 721-4766-1263
                                                                 D-50170 Kerpen                              certger@visteon.com
                                                                 Germany                                     www.visteon.com




                    Check that the connector of the vehicle are not damaged and that no connector wires
                     are entangled.
                    After connection, ensure that the connector is fully and properly inserted into the
                     corresponding connector socket. Close the connector by its retaining clip.

          Antenna cables
          Antenna cable is a part of the cable connected to the IC. The length of the antenna cable
          varies between 50 cm and 130 cm depending on the vehicle type, antenna type and steering
          wheel position. The cable is affixed on skeins or metal girders on the surfaces of the vehicle’s
          bulkheads, the specific fixing mechanism is dependent on the vehicle’s model.

          Connection Recommendations
                    Once laid, cables must not touch any part of the IC casing.
                    Once laid, cables must not hamper thermal dissipation from the IC.
                    All cables must be protected against wear and tear caused by friction with any parts of
                     their surroundings.




                                                                              2
Visteon Electronics Germany GmbH
Sitz der Gesellschaft / Place of Business: Kerpen        Geschäftsführung / Management Board    Bank: Bank of America Merrill Lynch
Registergericht / Registration Office: Köln, HRB 78269   Jens Tillner                           Konto Nr. / Account No: 20569017
USt-IDNR. / VAT ID: DE 294 194 802                       Jochen Ladwig                          IBAN: DE96 5001 0900 0020 5690 17
Steuer Nr. / Tax No: 203/5788/1299                                                              SWIFT / BIC code: BOFADEFX


                                                                 Visteon Electronics Germany GmbH            +49 (0) 721-4766-1900
                                                                 Visteonstrasse 4-10                         +49 (0) 721-4766-1263
                                                                 D-50170 Kerpen                              certger@visteon.com
                                                                 Germany                                     www.visteon.com




          Annexes




          Figure 1: IC Mounting fixtures
                                                                              3
Visteon Electronics Germany GmbH
Sitz der Gesellschaft / Place of Business: Kerpen        Geschäftsführung / Management Board    Bank: Bank of America Merrill Lynch
Registergericht / Registration Office: Köln, HRB 78269   Jens Tillner                           Konto Nr. / Account No: 20569017
USt-IDNR. / VAT ID: DE 294 194 802                       Jochen Ladwig                          IBAN: DE96 5001 0900 0020 5690 17
Steuer Nr. / Tax No: 203/5788/1299                                                              SWIFT / BIC code: BOFADEFX



Document Created: 2019-03-11 13:59:45
Document Modified: 2019-03-11 13:59:45

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC