Attachment Exhibit A

This document pretains to SES-LIC-20141203-00880 for License on a Satellite Earth Station filing.

IBFS_SESLIC2014120300880_1070349

Exhibit A Radiation Hazard Report Page 1 of 5 Analysis of Non-Ionizing Radiation for a 3.7-Meter Earth Station System This report analyzes the non-ionizing radiation levels for a 3.7-meter earth station system. The analysis and calculations performed in this report comply with the methods described in the FCC Office of Engineering and Technology Bulletin, No. 65 first published in 1985 and revised in 1997 in Edition 97-01. The radiation safety limits used in the analysis are in conformance with the FCC R&O 96-326. Bulletin No. 65 and the FCC R&O specifies that there are two separate tiers of exposure limits that are dependant on the situation in which the exposure takes place and/or the status of the individuals who are subject to the exposure. The Maximum Permissible Exposure (MPE) limits for persons in a General Population/Uncontrolled environment are shown in Table 1. The General Population/Uncontrolled MPE is a function of transmit frequency and is for an exposure period of thirty minutes or less. The MPE limits for persons in an Occupational/Controlled environment are shown in Table 2. The Occupational MPE is a function of transmit frequency and is for an exposure period of six minutes or less. The purpose of the analysis described in this report is to determine the power flux density levels of the earth station in the far-field, near-field, transition region, between the subreflector or feed and main reflector surface, at the main reflector surface, and between the antenna edge and the ground and to compare these levels to the specified MPEs. Table 1. Limits for General Population/Uncontrolled Exposure (MPE) Frequency Range (MHz) Power Density (mW/cm2) 30-300 0.2 300-1500 Frequency (MHz)*(0.8/1200) 1500-100,000 1.0 Table 2. Limits for Occupational/Controlled Exposure (MPE) Frequency Range (MHz) Power Density (mW/cm2) 30-300 1.0 300-1500 Frequency (MHz)*(4.0/1200) 1500-100,000 5.0 Table 3. Formulas and Parameters Used for Determining Power Flux Densities Parameter Symbol Formula Value Units Antenna Diameter D Input 3.7 m Antenna Surface Area Asurface π D2 / 4 10.75 m2 Subreflector Diameter Dsr Input 48.0 cm Area of Subreflector Asr π Dsr 2/4 1809.56 cm2 Frequency F Input 14250 MHz Wavelength λ 300 / F 0.021053 m Transmit Power P Input 300.00 W Antenna Gain (dBi) Ges Input 52.6 dBi Antenna Gain (factor) G 10Ges/10 181970.1 n/a Pi π Constant 3.1415927 n/a Antenna Efficiency η Gλ2/(π2D2) 0.60 n/a

Exhibit A Radiation Hazard Report Page 2 of 5 1. Far Field Distance Calculation The distance to the beginning of the far field can be determined from the following equation: Distance to the Far Field Region Rff = 0.60 D2 / λ (1) = 390.2 m The maximum main beam power density in the far field can be determined from the following equation: On-Axis Power Density in the Far Field Sff = G P / (4 π Rff 2) (2) = 28.537 W/m2 = 2.854 mW/cm2 2. Near Field Calculation Power flux density is considered to be at a maximum value throughout the entire length of the defined Near Field region. The region is contained within a cylindrical volume having the same diameter as the antenna. Past the boundary of the Near Field region, the power density from the antenna decreases linearly with respect to increasing distance. The distance to the end of the Near Field can be determined from the following equation: Extent of the Near Field Rnf = D2 / (4 λ) (3) = 162.6 m The maximum power density in the Near Field can be determined from the following equation: Near Field Power Density Snf = 16.0 η P / (π D2) (4) = 66.619 W/m2 = 6.662 mW/cm2 3. Transition Region Calculation The Transition region is located between the Near and Far Field regions. The power density begins to decrease linearly with increasing distance in the Transition region. While the power density decreases inversely with distance in the Transition region, the power density decreases inversely with the square of the distance in the Far Field region. The maximum power density in the Transition region will not exceed that calculated for the Near Field region. The power density calculated in Section 1 is the highest power density the antenna can produce in any of the regions away from the antenna. The power density at a distance Rt can be determined from the following equation: Transition Region Power Density St = Snf Rnf / Rt (5) = 6.662 mW/cm2

Exhibit A Radiation Hazard Report Page 3 of 5 4. Region between the Main Reflector and the Subreflector Transmissions from the feed assembly are directed toward the subreflector surface, and are reflected back toward the main reflector. The most common feed assemblies are waveguide flanges, horns or subreflectors. The energy between the subreflector and the reflector surfaces can be calculated by determining the power density at the subreflector surface. This can be determined from the following equation: Power Density at the Subreflector Ssr = 4000 P / Asr (6) = 663.146 mW/cm2 5. Main Reflector Region The power density in the main reflector is determined in the same manner as the power density at the subreflector. The area is now the area of the main reflector aperture and can be determined from the following equation: Power Density at the Main Reflector Surface Ssurface = 4 P / Asurface (7) = 111.606 W/m2 = 11.161 mW/cm2 6. Region between the Main Reflector and the Ground Assuming uniform illumination of the reflector surface, the power density between the antenna and the ground can be determined from the following equation: Power Density between Reflector and Ground Sg = P / Asurface (8) = 27.902 W/m2 = 2.790 mW/cm2

Exhibit A Radiation Hazard Report Page 4 of 5 7. Summary of Calculations Table 4. Summary of Expected Radiation levels for Uncontrolled Environment Calculated Maximum Radiation Power Density Level Region (mW/cm2) Hazard Assessment 1. Far Field (Rff = 390.2 m) Sff 2.854 Potential Hazard 2. Near Field (Rnf = 162.6 m) Snf 6.662 Potential Hazard 3. Transition Region (Rnf < Rt < Rff) St 6.662 Potential Hazard 4. Between Main Reflector and Ssr 663.146 Potential Hazard Subreflector 5. Main Reflector Ssurface 11.161 Potential Hazard 6. Between Main Reflector and Ground Sg 2.790 Potential Hazard Table 5. Summary of Expected Radiation levels for Controlled Environment Calculated Maximum Radiation Power Density Region Level (mW/cm2) Hazard Assessment 1. Far Field (Rff = 390.2 m) Sff 2.854 Satisfies FCC MPE 2. Near Field (Rnf = 162.6 m) Snf 6.662 Potential Hazard 3. Transition Region (Rnf < Rt < Rff) St 6.662 Potential Hazard 4. Between Main Reflector and Ssr 663.146 Potential Hazard Subreflector 5. Main Reflector Ssurface 11.161 Potential Hazard 6. Between Main Reflector and Ground Sg 2.790 Satisfies FCC MPE It is the applicant's responsibility to ensure that the public and operational personnel are not exposed to harmful levels of radiation.

Exhibit A Radiation Hazard Report Page 5 of 5 8. Conclusions Based upon the above analysis, it is concluded that FCC RF Guidelines have been exceeded in the specified region(s) of Tables 4 and 5. The applicant proposes to comply with the Maximum Permissible Exposure (MPE) limits of 1.0 mW/cm**2 for the Uncontrolled Areas, and the MPE limits of 5.0 mW/cm**2 for the Controlled Areas. The earth station will be installed on the lower roof of a building on the campus of Oklahoma State University, in Stillwater, Oklahoma. The lower roof of the building is 12 feet in height, and public access to that roof is restricted. The applicant will ensure that the main beam of the antenna will be pointed at least one diameter away from any buildings, or other obstacles in those areas that exceed the MPE levels. Since one diameter removed from the center of the main beam the levels are down at least 20 dB, or by a factor of 100, public safety will be ensured. The earth station will marked with the standard radiation hazard warnings, as well as the area in the vicinity of the earth station, to inform those in the general population, who may be working, or otherwise present on the roof, and in or near, the main beam of the antenna. Finally, occupational exposure will be limited, and the transmitter will be turned off during periods of maintenance, so that the MPE standard of 5.0 mw/cm**2 will be complied with for those regions in close proximity to the main reflector, and subreflector, which could be occupied by operating personnel. The applicant agrees to abide by the conditions specified in Condition 5208 provided below: Condition 5208 - The licensee shall take all necessary measures to ensure that the antenna does not create potential exposure of humans to radiofrequency radiation in excess of the FCC exposure limits defined in 47 CFR 1.1307(b) and 1.1310 wherever such exposures might occur. Measures must be taken to ensure compliance with limits for both occupational/controlled exposure and for general population/uncontrolled exposure, as defined in these rule sections. Compliance can be accomplished in most cases by appropriate restrictions such as fencing. Requirements for restrictions can be determined by predictions based on calculations, modeling or by field measurements. The FCC's OET Bulletin 65 (available on-line at www.fcc.gov/oet/rfsafety) provides information on predicting exposure levels and on methods for ensuring compliance, including the use of warning and alerting signs and protective equipment for worker.


Document Created: 2014-12-02 10:39:38
Document Modified: 2014-12-02 10:39:38
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC