Attachment SESLIC2013081300723R

SESLIC2013081300723R

SUPPLEMENT submitted by IHLAS HABER AJANSI IHA

RADIATION HAZARD STUDY

0000-00-00

This document pretains to SES-LIC-20130813-00723 for License on a Satellite Earth Station filing.

IBFS_SESLIC2013081300723_1008678

ANALYSIS OF A NON-IONIZING RADIATION FOR A 1.35 METER EARTH STATION SYSTEM This report analysis the non-ionizing radiation levels for a 1.35-m earth station system. The analysis and calculations in this report comply with the methods described in the FCC Office of Engineering and Technology Bulletin, No.65. The radiation safety limits used in the analysis are in conformance with the FCC R&O 96-326. Bulletin No.65 and the FCC R&O specifies that there are two separate tiers of exposure limits that are dependent on the situation in which the exposure takes place and/or the status of the individuals who are subject to the exposure. The Maximum Permissible Exposure (MPE) limits for person in a General Population/Uncontrolled environment are shown in Table 1. MPE limits for persons in an Occupation/Controlled environment are shown in Table 2. The purpose of the analysis of this report is to determine the power flux density levels and to compare these levels to the specified MPEs Table 1 – Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Power Density (mW/cm2) 30-300 0.2 300-1500 Frequency (MHz)*(0.8/1200) 1500-100,000 1.0 Table 2 – Limits for General Occupational/Controlled Exposure (MPE) Frequency Range (MHz) Power Density (mW/cm2 30-300 1.0 300-1500 Frequency (MHz)*(0.8/1200) 1500-100,000 5.0 Table 3 – Formulas and Parameters Used for Determining Power Flux Densities Parameter Value Units Antenna Diameter 1.35 m Antena Surface Area 1.431388153 m2 Subreflector Diameter 0 cm Area of Subreflector 0 cm2 Frequency 14250 MHz Wavelength 0.02105263 m Transmit Power 20 W Antenna Gain (dBi) 44.02 dBi Antenna Gain (factor) 25234.81 n/a Pi 3.1415927 n/a Antenna Efficiency 0.621793 n/a 1. Far Field Distance Calculation The distance to the beginning of the far field (Rff) and the on-axis power density (Sff) are calculated as below Rff = 51.941 m Sff = 1.489 mW/cm2 2. Near Field Distance Calculation The distance to the end of the Near Field (Rnf) and the maximum power density in the Near

Field (Snf) are calculated as below Rnf = 21.642 m Snf = 3.475 mW/cm2 3. Transition Region Calculation The Transit Region is located between Near Field and Far Field Regions. The maximum power density in the Transit Region will not exceed that calculated for the Near Field region. The power density in the Transit Region (St) at a distance Rt is calculated as below St = 3.475 mW/cm2 , 4. Region Between the Main Reflector and Subrefletor No Subreflector used in this system 5. Main Reflector Region Power density at the Main reflector Surface Ssurface (Ssurface) is calculated as below Ssurface = 5.589 mW/cm2 6. Region Between the main reflector and the Ground Power density between the Main Reflector and the Ground (Sg) is calculated as below Sg = 1.397 mW/cm2 7. SUMMARY OF CALCULATIONS Table 4. Summary of expected Radiation Levels for Uncontrolled Enviroment Expected Maximum Distance Hazard Region Radiation Power (m) Assesement Density Level mW/cm2 Satisfiecs FCC Far Field (Sff) 51.941 1.489 MPE Satisfiecs FCC Near Field (Snf) 21.642 3.475 MPE Satisfiecs FCC Transition Region (St) 3.475 MPE Main Reflector 5.589 Potential Hazard (Ssurface) Between Main Satisfiecs FCC Reflector & Ground 1.397 MPE (Sg) Table 5. Summary of Expected Ration Levels for Controlled Enviroment Expected Maximum Distance Hazard Region Radiation Power (m) Assesement Density Level mW/cm2 Far Field (Sff) 51.941 1.489 Potential Hazard

Near Field (Snf) 21.642 3.475 Potential Hazard Transition Region (St) 3.475 Potential Hazard Main Reflector 5.589 Potential Hazard (Ssurface) Between Main Reflector & Ground 1.397 Potential Hazard (Sg) CONCLUSION Based upon the above analysis it’s concluded that FCC RF Guidelines have been exceeded in the specific region(s) of Table 4. The applicant proposes to comply with MPE limits of Uncontrolled and Controlled areas. The antenna will be installed on top of the applicant’s truck. The applicant will mark the earth station with the standard radiation hazard warnings. Since one diameter removed from the center of the main beam the levels are down at least 20 dB, or by a factor of 100, these potential hazards do not exist for either the public, or for earth station personnel. The applicant will ensure that the main beam of the antenna will be pointed at least one diameter away from any buildings or other obstacles in those areas that exceed the MPE levels. Finally the earth station’s operation personnel will not have access to areas that exceeds the MPE levels, while the earth station is in operation. The transmitter will be turned off during the periods of maintenance, so that MPE standards will be complied with for those regions in close proximity to the main reflector, which could be occupied by operating personnel.


Document Created: 2013-08-21 16:14:11
Document Modified: 2013-08-21 16:14:11
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC