Attachment RF_Exposure

This document pretains to SES-LIC-20130521-00438 for License on a Satellite Earth Station filing.

IBFS_SESLIC2013052100438_996404

Engineering Statement RADIOFREQUENCY EXPOSURE CALCULATIONS prepared for WISN Hearst Television Inc. WISN Hearst Television Inc. (“WISN”) is the applicant for a transportable “Ku Band” satellite uplink license. The following study was conducted to evaluate the proposed facility with respect to the potential for human exposure to radiofrequency (“RF”) electromagnetic field. Specifically, the study determined whether exposure to RF electromagnetic field would exceed FCC maximum permissible exposure limits to the general public and to occupational workers at locations in the vicinity of the uplink antenna based on data provided by the applicant and representatives of the equipment manufacturers. Human Exposure to Radiofrequency Electromagnetic Field The WISN proposed operation was evaluated using the procedures outlined in FCC OET Bulletin No. 65 (“OET 65"). OET 65 describes a means of determining whether a proposed facility exceeds the RF exposure guidelines specified in §1.1310 of the Rules. Under present Commission policy, a facility may be presumed to comply with the limits in §1.1310 if it satisfies the exposure criteria set forth in OET 65. Based upon that methodology, and as demonstrated in the following, the transmitting system under study will comply with the cited adopted guidelines at publicly accessible locations when procedures described herein are followed. Public Exposure The mechanical design of the mounting equipment is optimized to orient the antenna toward satellites that are located well above the horizon. Prevention of public exposure to predicted RF electromagnetic field in excess of the general population/uncontrolled limit1 depends on adherence to the following operational guidelines by the WISN technicians. As shown below, RF attributable to the WISN uplink antenna at locations outside of the “main beam” and 1.35 meters or more from the center of the main beam will not exceed the FCC general population and uncontrolled RF exposure limits. According to representatives of WISN, at its lowest elevation, the center of the uplink antenna is 4.0 meters above the ground and thus more than one dish- diameter above head level (2 meters) on level terrain. 1 The general population/uncontrolled maximum permissible exposure (“MPE”) limit of 1 mW/cm² for 14,250 MHz is specified in §1.1310 of the Rules. Cavell, Mertz & Associates, Inc.

Engineering Statement (page 2 of 4) To assure that no publicly accessible area is within the “main beam” of the uplink antenna, sites and satellites will be selected such that the elevation angle of the antenna will always exceed five degrees and the main beam is 1.35 meters above the horizon, nearby buildings, and places accessible by the public. In unusual cases where this isolation cannot be achieved, WISN will utilize crowd control stanchions, cones, and RF exposure warning signs to control access to areas that are known to exceed the FCC’s general population uncontrolled MPE limit. These areas will be defined either by measurements made by qualified, on-site personnel, or by the calculations described herein. Based on data provided by the applicant, the following parameters were used in the study: Antenna Manufacturer General Dynamics Antenna Model C135M Center Transmit Frequency 14,250 MHz Wavelength at Center Frequency 0.021 meters Max Average Antenna Input Power 108.87 Watts Antenna Diameter 1.35 meters Antenna Gain 44.3 dBi Antenna Gain Ratio 26915.3 Antenna Aperture Efficiency 0.662 The area in the immediate vicinity of the antenna is known as the “near field region.” In this region (up to 21.7 meters in the case at hand), the antenna directional characteristics have not fully formed. Therefore, antenna manufacturer “off-axis” discrimination specifications cannot be utilized for the purpose of determining potential RF exposure. OET 65 provides a methodology (Equation 13) for calculating a “worst case” exposure figure within this region. Additionally, OET 65 specifies that the “worst case” power density would be reduced by 20 dB at locations at least one antenna diameter (1.35 meters) off-axis from the “main beam” of the antenna. In this instance, the predicted off-axis, near field is 0.201 mW/cm², or 20.1 percent of the general population/uncontrolled limit. Off-axis predicted fields reduce commensurately at greater distances from the antenna in the antenna transition region. In the “far field” region of the antenna (in this case, starting at a distance of 52.0 meters from the antenna), the antenna directional characteristics have formed and the off-axis power density can be readily calculated using “off-axis” antenna discrimination specifications. At locations greater than five Cavell, Mertz & Associates, Inc. 2013069DGR

Engineering Statement (page 3 of 4) degrees off-axis from the “main beam,” the manufacturer of the proposed antenna specifies a minimum side-lobe attenuation of 29.8 dB.2 Again using the methodology detailed in OET 65, this “off-axis” attenuation is predicted to result in a power density of 0.0091 mW/cm², or 0.91 percent of the general population/uncontrolled limit. Controlled Access Area Exposure Access to the vicinity of the antenna will be limited and restricted to authorized, trained personnel. Using data provided by the applicant, the potential for RF exposure to occupational workers was evaluated. As described previously, the maximum predicted off-axis, “near field” power density is 0.201 mW/cm², which is 4.02 percent of the controlled limit. As the operator will generally be posted at locations at ground level or within the truck itself, it is anticipated that actual exposure will be substantially less than the above “worst case” prediction. With respect to worker safety, it is believed that based on the preceding analysis, excessive exposure would not occur provided that adequate physical separation is established. As mentioned previously, detailed operator policy will be employed protecting workers from excessive exposure when work must be performed where high RF levels may be present. Such protective measures may include, but will not be limited to, restriction of access to areas where levels in excess of the guidelines may be expected, or the complete shutdown of facilities when work or inspections must be performed in areas where the exposure guidelines would otherwise be exceeded. On-site RF exposure measurements may also be undertaken to establish the bounds of safe working areas. The applicant will coordinate exposure procedures with all pertinent facilities. Conclusion As demonstrated, excessive levels of RF energy will not be caused at publicly accessible areas by strictly following the policy detailed herein. Consequently, neither the general public nor occupational staff will be exposed to RF levels in excess of the Commission’s guidelines. Whenever necessary to assure compliance, access to the vicinity of the uplink antenna will be restricted and controlled through the use of crowd control stanchions, cones, and conspicuous RFR warning signs as part of an overall RF safety program. The above study presumes that the subject antenna is the sole source of RF energy at the 2 According to the manufacturer, the antenna meets the minimum off-axis specification detailed in FCC Rule §25.209(a)(2) or 32-25 Log(θ) dBi. Cavell, Mertz & Associates, Inc. 2013069DGR

Engineering Statement (page 4 of 4) uplink site. In the case of multiple emitters, further analysis or measurement is necessary to assure compliance. Certification The undersigned hereby certifies that the foregoing statement was prepared by him or under his direction, and that it is true and correct to the best of his knowledge and belief. Mr. Ryson is a senior engineer in the firm of Cavell, Mertz & Associates, Inc. Daniel G. Ryson May 8, 2013 Cavell, Mertz & Associates, Inc. 7732 Donegan Dr. Manassas, VA 20109-2686 (703) 392-9090 Cavell, Mertz & Associates, Inc. 2013069DGR


Document Created: 2013-05-08 10:02:03
Document Modified: 2013-05-08 10:02:03
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC