Attachment E110100REVISEDRADHAD

E110100REVISEDRADHAD

SUPPLEMENT submitted by INTELSAT LICENSE LLC

REVISED RADIATION HAZARD STUDY

2011-07-06

This document pretains to SES-LIC-20110627-00745 for License on a Satellite Earth Station filing.

IBFS_SESLIC2011062700745_904063

Radiation Hazard Report Page 1 of 5 Analysis of Non-Ionizing Radiation for a 3.8-Meter Earth Station System This report analyzes the non-ionizing radiation levels for a 3.8-meter earth station system. The analysis and calculations performed in this report comply with the methods described in the FCC Office of Engineering and Technology Bulletin, No. 65 first published in 1985 and revised in 1997 in Edition 97-01. The radiation safety limits used in the analysis are in conformance with the FCC R&O 96-326. Bulletin No. 65 and the FCC R&O specifies that there are two separate tiers of exposure limits that are dependant on the situation in which the exposure takes place and/or the status of the individuals who are subject to the exposure. The Maximum Permissible Exposure (MPE) limits for persons in a General Population/Uncontrolled environment are shown in Table 1. The General Population/Uncontrolled MPE is a function of transmit frequency and is for an exposure period of thirty minutes or less. The MPE limits for persons in an Occupational/Controlled environment are shown in Table 2. The Occupational MPE is a function of transmit frequency and is for an exposure period of six minutes or less. The purpose of the analysis described in this report is to determine the power flux density levels of the earth station in the far-field, near-field, transition region, between the subreflector or feed and main reflector surface, at the main reflector surface, and between the antenna edge and the ground and to compare these levels to the specified MPEs. Table 1. Limits for General Population/Uncontrolled Exposure (MPE) Frequency Range (MHz) Power Density (mW/cm2) 30-300 0.2 300-1500 Frequency (MHz)*(0.8/1200) 1500-100,000 1.0 Table 2. Limits for Occupational/Controlled Exposure (MPE) Frequency Range (MHz) Power Density (mW/cm2) 30-300 1.0 300-1500 Frequency (MHz)*(4.0/1200) 1500-100,000 5.0 Table 3. Formulas and Parameters Used for Determining Power Flux Densities Parameter Symbol Formula Value Units Antenna Diameter D Input 3.8 m Antenna Surface Area Asurface π D2 / 4 11.34 m2 Feed Flange Diameter Dfa Input 19.1 cm Area of Feed Flange Afa π Dfa 2/4 286.52 cm2 Frequency F Input 6175 MHz Wavelength λ 300 / F 0.048583 m Transmit Power P Input 376.70 W Antenna Gain (dBi) Ges Input 46.0 dBi Antenna Gain (factor) G 10Ges/10 39810.7 n/a Pi π Constant 3.1415927 n/a Antenna Efficiency η Gλ2/(π2D2) 0.66 n/a

Radiation Hazard Report Page 2 of 5 1. Far Field Distance Calculation The distance to the beginning of the far field can be determined from the following equation: Distance to the Far Field Region Rff = 0.60 D2 / λ (1) = 178.3 m The maximum main beam power density in the far field can be determined from the following equation: On-Axis Power Density in the Far Field Sff = G P / (4 π Rff 2) (2) = 37.525 W/m2 = 3.752 mW/cm2 2. Near Field Calculation Power flux density is considered to be at a maximum value throughout the entire length of the defined Near Field region. The region is contained within a cylindrical volume having the same diameter as the antenna. Past the boundary of the Near Field region, the power density from the antenna decreases linearly with respect to increasing distance. The distance to the end of the Near Field can be determined from the following equation: Extent of the Near Field Rnf = D2 / (4 λ) (3) = 74.3 m The maximum power density in the Near Field can be determined from the following equation: Near Field Power Density Snf = 16.0 η P / (π D2) (4) = 87.599 W/m2 = 8.760 mW/cm2 3. Transition Region Calculation The Transition region is located between the Near and Far Field regions. The power density begins to decrease linearly with increasing distance in the Transition region. While the power density decreases inversely with distance in the Transition region, the power density decreases inversely with the square of the distance in the Far Field region. The maximum power density in the Transition region will not exceed that calculated for the Near Field region. The power density calculated in Section 1 is the highest power density the antenna can produce in any of the regions away from the antenna. The power density at a distance Rt can be determined from the following equation: Transition Region Power Density St = Snf Rnf / Rt (5) = 8.760 mW/cm2

Radiation Hazard Report Page 3 of 5 4. Region between the Feed Assembly and the Antenna Reflector Transmissions from the feed assembly are directed toward the antenna reflector surface, and are confined within a conical shape defined by the type of feed assembly. The most common feed assemblies are waveguide flanges, horns or subreflectors. The energy between the feed assembly and reflector surface can be calculated by determining the power density at the feed assembly surface. This can be determined from the following equation: Power Density at the Feed Flange Sfa = 4000 P / Afa (6) = 5258.949 mW/cm2 5. Main Reflector Region The power density in the main reflector is determined in the same manner as the power density at the feed assembly. The area is now the area of the reflector aperture and can be determined from the following equation: Power Density at the Reflector Surface Ssurface = 4 P / Asurface (7) = 132.861 W/m2 = 13.286 mW/cm2 6. Region between the Reflector and the Ground Assuming uniform illumination of the reflector surface, the power density between the antenna and the ground can be determined from the following equation: Power Density between Reflector and Ground Sg = P / Asurface (8) = 33.215 W/m2 = 3.322 mW/cm2

Radiation Hazard Report Page 4 of 5 7. Summary of Calculations Table 4. Summary of Expected Radiation levels for Uncontrolled Environment Calculated Maximum Radiation Power Density Level Region (mW/cm2) Hazard Assessment 1. Far Field (Rff = 178.3 m) Sff 3.752 Potential Hazard 2. Near Field (Rnf = 74.3 m) Snf 8.760 Potential Hazard 3. Transition Region (Rnf < Rt < Rff) St 8.760 Potential Hazard 4. Between Feed Assembly and Sfa 5258.949 Potential Hazard Antenna Reflector 5. Main Reflector Ssurface 13.286 Potential Hazard 6. Between Reflector and Ground Sg 3.322 Potential Hazard Table 5. Summary of Expected Radiation levels for Controlled Environment Calculated Maximum Radiation Power Density Region Level (mW/cm2) Hazard Assessment 1. Far Field (Rff = 178.3 m) Sff 3.752 Satisfies FCC MPE 2. Near Field (Rnf = 74.3 m) Snf 8.760 Potential Hazard 3. Transition Region (Rnf < Rt < Rff) St 8.760 Potential Hazard 4. Between Feed Assembly and Sfa 5258.949 Potential Hazard Antenna Reflector 5. Main Reflector Ssurface 13.286 Potential Hazard 6. Between Reflector and Ground Sg 3.322 Satisfies FCC MPE It is the applicant's responsibility to ensure that the public and operational personnel are not exposed to harmful levels of radiation. 8. Conclusions Based on the above analysis it is concluded that the FCC MPE guidelines have been exceeded (or met) in the regions of Table 4 and 5. The applicant proposes to comply with the MPE limits by one or more of the following methods. Means of Compliance Uncontrolled Areas This antenna will be located on the rooftop of a building. The rooftop will be not be accessible by the general public. The rooftop area will be sufficient to prohibit the general public from having access the areas that exceed the MPE limits Since one diameter removed from the main beam of the antenna or ½ diameter removed from the edge of the antenna the RF levels are reduced by a factor of 100 or 20 dB. None of the areas exceeding the MPE levels will be accessible by the general public.

Radiation Hazard Report Page 5 of 5 Radiation hazard signs will be posted while this earth station is in operation. The applicant will ensure that no buildings or other obstacles will be in the areas that exceed the MPE levels. Means of Compliance Controlled Areas The earth station’s operational personnel will not have access to the areas that exceed the MPE levels while the earth station is in operation. The transmitters will be turned off during antenna maintenance. Prepared By Timothy O. Crutcher Frequency Planner COMSEARCH 19700 Janelia Farm Boulevard Ashburn, VA 20147 DATED: July 6, 2011


Document Created: 2011-07-06 15:24:12
Document Modified: 2011-07-06 15:24:12
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC