SAR Test Report - Part 2

FCC ID: 2ASJS-HR600

RF Exposure Info

Download: PDF
FCCID_4274042

NTEKIE:I6 [accreoiteo) Certificate #4258.01 ~ SAR Reference Dipole Calibration Report Ref : ACR.109.2.18.SATU.A SHENZHEN NTEK TESTING TECHNOLOGY CO., LTD. BUILDING E, FENDA SCIENCE PARK, SANWEI COMMUNITY, XIXIANG STREET, BAO‘AN DISTRICT, SHENZHEN GUANGDONG, CHINA MVG COMOSAR REFERENCE DIPOLE FREQUENCY: 835 MHZ SERIAL NO.: SN 03/15 DIP 0G835—347 Calibrated at MVG US 2105 Barrett Park Dr. — Kennesaw, GA 30144 fncws t k wA 4./7';‘\\‘\? [accrepitep caitvetion cent azzesor Calibration Date: 04/19/2018 Summary: This document presents the method and results from an accredited SAR reference dipole calibration performed in MVG USA using the COMOSAR test bench. All calibrationresults are traceable to national metrology institutions.

NTEKIE:W °_ {accrepiteo) Certificate #4258.01 ~ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.109.2.18.SATU.A Name Function Date Signature Prepared by : JTérome LUC Product Manager 4/19/2018 57,%’ Checked by: Jérome LUC Product Manager 4/19/2018 fi Approved by : Kim RUTKOWSKIT Quality Manager 4/19/2018 Jum PathastP! Customer Name SHENZHEN NTEK ooie TESTING Distribution : TECHNOLOGY CO.. LTD. Issue Date Modifications A 4/19/2018 Initial release Page: 2/11 This document shall not be reproduced, exeept infull orin part, without the written approval ofMVG. The information contained herein is to be used onlyfor the puposefor whichit is submitted and is not to be released in whole orpart without writen approval ofMVG.

NTEKIE:W Accreviteo Certificate #4258.01 ~ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.109.2.18.SATU.A TABLE OF CONTENTS TELOGUCHOM..ccccecece cesc nennene en en nnnnnnnnnnnnnnennnnnn en n en en en nnnnnnnnnennnnnnenneennnennee en 4 DeVi@G@ UDG@T T@St ......2.0.0000000000000eieeeeee enc nnnnnnenenennnnenne es 4 bo PTOGUCt D@SCTIDMOM as..2.0.0000000000000e en eeeeemeeeenenene e vene en vverenmennenemennenenene en vevne en nemens 4 w0 3.1 General Information 4 4 hoEenGnalCol e 5 4.1 Return Loss Requirements 5 4.2 Mechanical Requirements 5 hoEesoenval Sne e 5 5.1 Return Loss 5 5.2 Dimension Measurement 5 5.3 Validation Measurement 5 CalibDratioN MEASUTEMENT ReSUITS ...........c.cnccsce cesc 6 6.1 Return Loss and Impedance In Head Liquid 6 6.2 Return Loss and Impedance In Body Liquid 6 6.3 Mechanical Dimensions 6 VAIGAION I@ASUT@DNENE ........2....0.00000000000000 00e ee ce mnmnmmnnnmemnnnnnmmeme mm es 7 7.1 Head Liquid Measurement 7 7.2 SAR Measurement Result With Head Liquid 8 7.3 Body Liquid Measurement 9 7.4 SAR Measurement Result With Body Liquid 10 LiSt Of EQUIDIM@ME ..2.0.00.0.000000000000 0e en e eemev en vvre en vverenmennevemmnenev en en vvne en n 11 co Page: 3/11 This document shall not be reproduced, except in full orim part, without the written approval ofMVG. The information contained herein is to be used onlyforthe purposeforwhich it is submitted and is not to be released in whole orpart without written approval ofMVG.

NT Certificate 84298 01 ~ mvG SaR REFERENCE DIPOLE CALIBRATION REPORT Ref ACR.109.2.18.SATUA 1 INTRODUCTION This document contains a summary of the requirements set forth by the IEEE 1528. FCC KDBs and CEMIEC 62209 standards forreference dipoles used for SAR measurement system validations and the measurements that were performed to verifythat the product complies with the fore mentioned standards. 2 DEVICE UNDER TEST Device Under Test Device Type COMOSAR 835 MHz REFERENCE DIPOLE Manufacturer MVG Model SID835 Serial Number SN 03/15 DIP 0G835—347 Product Condition (new / used) Used A yearly calibration interval is recommended. 3 PRODUCT DESCRIPTION 3.1 GENERAL INFORMATION MVG‘s COMOSAR Validation Dipoles are built in accordance to the IEEE 1528, FCC KDBs and CEMIEC 62209 standards. The product is designed for use with the COMOSAR test bench only. Figure 1 — MVG COMOSAR Validation Dipole Page: 4/11 This document shall not be reproduced, except in full orin part, without the written approval ofMVG. The information contained herein is to be used onlyforthe purpose forwhich it is submitted and is not to be released in whole orpart without written approval ofMVG.

NTEKJL:JJ*=« KA Certificate #4298.01 ~ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref ACR.109.2.18.SATUA 4 MEASUREMENT METHOD The IEEE 1528, FCC KDBs and CEIIEC 62209 standards provide requirements for reference dipoles used for system validation measurements. The following measurements were performed to verify that the product complies with the fore mentioned standards. 4.1 RETURNLOSS REQUIREMENTS The dipole used for SAR system validation measurements and checks must have a return loss of —20 dB or better. The return loss measurement shall be performed against a liquid filled flat phantom, with the phantom constructed as outlined in the fore mentioned standards. 4.2 MECHANICAL REQUIREMENTS The IEEE Std. 1528 and CEIMIEC 62209 standards specify the mechanical components and dimensions of the validation dipoles, with the dimensions frequency and phantom shell thickness dependent. The COMOSAR test bench employs a 2 mm phantom shell thickness therefore the dipoles sold for use with the COMOSAR test bench comply with the requirements set forth for a 2 mm phantomshell thickness. 5 MEASUREMENT UNCERTAINTY All uncertainties listed below represent an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. traceable to the Internationally Accepted Guides to Measurement Uncertainty. 5.1 RETURNLOSS The following uncertainties apply to the return loss measurement: Frequency band Expanded Uncertainty on Return Loss 400—6000MHz 0.1 dB 5.2 DIMENSION MEASUREMENT The following uncertainties apply to the dimension measurements: Length (mm) Expanded Uncertainty on Length 3 — 300 0.05 mm 5.3 VALIDATION MEASUREMENT The guidelines outlined in the IEEE 1528, FCC KDBs, CENELEC ENS0361 and CELIEC 62209 standards were followed to generate the measurement uncertainty for validation measurements. Scan Volume Expanded Uncertainty 1s 20.3 % Page: 5/11 This document shall not be reproduced, except in full orin part, without the written approval ofMVG. The information contained herein is to be used onlyforthe purpose forwhich it is submitted and is not to be released in whole orpart without written approval ofMVG.

NTEKIE:W Certificate #4258.01 SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR109.2.18.SATUA 10 g 20.1 % 6 CALIBRATION MEASUREMENT RESULTS 6.1 RETURN LOSS AND IMPEDANCE IN HEAD LIQUID Fequency, MHz 340 935 an— as— 59— Frequency (MHz) Return Loss (dB) Requirement (dB) Impedance 835 —23.67 —20 56.8 Q — 1.5 jQ 6.2 RETURN LOSS AND IMPEDANCE IN BODY LIQUID Frequency, MHz 00— Frequency (MHz) Return Loss (dB) Requirement (dB) Impedance 835 —27.64 —20 53.5 0 +23 jQ 6.3 MECHANICAL DIMENSIONS Frequency MHz L mm hmm d mm required measured required measured required measured 300 420.0 +1 %. 250.0 +1 %. 6.35 +1 %. Page: 6/11 This document shall not be reproduced, except in full orim part, without the written approval ofMVG. The information contained herein is to be used onlyforthe purposeforwhich it is submitted and is not to be released in whole orpart without written approval ofMVG.

NTEKIE:W (acer Accreoiteo) Certificate #4258.01 ~ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.109.2.18.SATUA 450 290.0 £1 %. 166.7 +1%. 6.35 +1 %. 750 176.0 £1%. 100.0 £1%. 6.35 41 %. 835 161.0 +1 %. PaSS 80.8 +1 %. PASS 3.6 +1 %. PASS 00 149.0 £1%. 83.3 +1 %. 3.6 £1 %. 1450 89.1 41 %. 517 41 %. 3.6 41 %. 1500 80.5 +1 %. 50.0 41 %. 3.6 +1 %. 1640 79.0 41 %. 45.7 41 %. 3.6 +1 %. 1750 75.2 41 %. 42.9 41 %. 3.6 +1 %. 1800 72.0 +1 %. 4127 +1 %. 3.6 +1 %. 1900 68.0 +1 %. 30.5 +1 %. 3.6 +1 %. 1950 66.3 +1 %. 38.5 +1 %. 3.6 +1 %. 2000 64.5 +1 %. 37.5 +1 %. 3.6 +1 %. 2100 61.0 +1 %. 35.7 +1 %. 3.6 +1 %. 2300 55.5 +1 %. 32.6 +1 %. 3.6 +1 %. 2450 51.5 +1 %. 30.4 +1 %. 3.6 +1 %. 2600 48.5 41 %. 28.8 11 %. 3.6 41 %. 3000 41.5 +1 %. 25.0 +1 %. 3.6 +1 %. 3500 37.041%. 26.4 +1 %. 3.6 +1 %. 3700 34.7+1%. 26.4 +1 %. 3.6 +1 %. 7 VALIDATION MEASUREMENT The IEEE Std. 1528. FCC KDBs and CEIIEC 62209 standards state that the system validation measurements must be performed using a reference dipole meeting the fore mentioned return loss and mechanical dimension requirements. The validation measurement must be performed against a liquid filled flat phantom, with the phantom constructed as outlined in the fore mentioned standards. Per the standards. the dipole shall be positioned below the bottom of the phantom. with the dipole length centered and parallel to the longest dimension of the flat phantom, with the top surface of the dipole at the described distance fromthe bottomsurface of the phantom. 7.1 HEAD LIQUID MEASUREMENT Fre:fll:zncy Relative permittivity (€;‘) Conductivity (0) 5/m required measured required measured 300 45.3 15 % 0.87 15 % 450 43.5 +5 % 0.87 +5 % 750 41.9 25 % 0.89 15 % 835 41.5 15 % PASS 0.90 15 % PASS 900 41.5 15 % 0.97 15 % 1450 40.5 15 % 1.20 25 % 1500 40.4 25 % 1.23 25 % 1640 40.2 25 % 13125 % 1750 40.1 15 % 1.3725% Page: 7/11 This document shall not be reproduced, except in full orin part, without the written approval ofMVG. The information contained herein is to be used onlyforthe purpose forwhich it is submitted and is not to be released in whole orpart without written approval ofMVG.

~~>o ([acerebiteo) Certificate #4258.01 ~ ‘ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.109.2.18.SATU A 1800 40.0 +5 % 140 45 % 1900 40.0 45 % 140 45% 1950 40.0 25 % 1.40 25% 2000 40.0 £5 % 1.40 £5% 2100 30.8 #5 % 149 £5% 2300 39.5 45 % 1.67 25 % 2450 39.2 45 % 1.80 45% 2600 39.0 45 % 1.96 45% 3000 38.5 +5 % 2.40 15 % 3500 37.9 #5 % 2.91 15 % 7.2 SAR MEASUREMENT RESULT WITH HEAD LIQUID The IEEE Std. 1528 and CEUIEC 62209 standards state that the system validation measurements should produce the SAR values shown below (for phantom thickness of 2 mm), within the uncertainty for the system validation. All SAR values are normalized to 1 W forward power. In bracket. the measured SAR is given with the used mput power. Software OPENSAR V4 Phantom SN 20/09 SAM7L Probe SN 18/11 EPG122 Liquid Head Liquid Values: eps‘ : 40.0 sigma : 0.90 Distance between dipole center and liquid 15.0 mm Area scan resolution dx=&mm/dy=8mm Zoon Scan Resolution dx=8mm/dy=8mm/dz=5mm Frequency 835 MHz Input power 20 dBm Liquid Temperature 21 °C Lab Temperature 21 °C Lab Humidity 45 % F’el‘\‘n'fil"c" 1 g SAR (W/kg/w) 10 g SAR (W/kg/W) required measured required measured 300 2.85 1.94 450 4.58 3.06 750 8.49 5.55 835 9.56 9.55 (0.95) 6.22 6.10 (0.61) 900 10.9 6.99 1450 29 16 1500 30.5 16.8 1640 34.2 18.4 1750 36.4 19.3 1800 38.4 20.1 Page: 8/11 This document shall not be reproduced, exeept infull orin part, without the written approval ofMVG. The information contained herein is to be used onlyforthe puposeforwhich itis submitted and is not to be released in whole orpart without writen approval ofMVG.

NTEKIE:W [accreoiteo) Certificate #4258.01 ~ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.109.2.18.SATU.A 1900 39.7 20.5 1950 40.5 20.9 2000 411 211 2100 43.6 219 2300 48.7 233 2450 52.4 24 2600 55.3 24.6 3000 63.8 25.7 3500 67.1 25 3700 67.4 24.2 memmmome Sutice rasvine Ciaze w3 tnw is (ot 1Cs s 15e test l lme (ek 1t s 12 santes 2‘ mas Eie o« Waer) gel 8: to fr ta te te 20 22 on ts 2e tC F7 xb BC Y Z ind 7.3 BODY LIQUID MEASUREMENT F re:/ll:-leln:y Relative permittivity (€)) Conductivity (0) S/m required measured required measured 150 61.9 15 % 0.80 15 % 300 58.2 +5 % 0.92 +5 % 450 56.7 15 % 0.94 15 % 750 55.5 15 % 0.96 15 % 835 55.2 15 % PASS 0.97 15 % PASS 900 55.0 15 % 1.05 15 % 915 55.0 15 % 1.06 15 % 1450 54.0 +5 % 1.30 +5 % 1610 53.8 15 % 140 25 % 1800 53.3 15 % 1.52 45 % 1900 53.3 15 % 1.52 45 % 2000 53.3 15 % 1.52 15 % 2100 53.2 +5 % 1.62 +5 % Page: 9/11 This document shall not be reproduced, except in full orim part, without the written approval ofMVG. The information contained herein is to be used onlyforthe purposeforwhich it is submitted and is not to be released in whole orpart without written approval ofMVG.

NTEKIE:W [accreoiteo) Certificate #4258.01 SAR REFERENCE DIPOLE CALIBRATION REPORT Ref ACR.100.2.18.SATUA 2300 52.9 15 % 1.81 15 % 2450 52.7 15 % 1.95 15. % 2600 52.5 15 % 2.16 15 % 3000 52.0 £5 % 2.73 25 % 3500 51.3 +5 % 3.31 15 % 3700 51.0 £5 % 3.55 15 % 5200 49.0 110 % 5.30 110 % 5300 48.9 110 % 5.42 +10 % 5400 48.7 210 % 5.53 210 % 5500 48.6 £10 % 5.65 10 % 5600 48.5 £10 % 5.77 10 % 5800 48.2 110 % 6.00 110 % 74 SAR MEASUREMENT RESULT WITH BODY LIQUID Software OPENSAR V4 Phantom SN 20/09 SAMT7I Probe SN 18/11 EPG122 Liquid Body Liquid Values: eps‘ : 57.5 sigma : 0.96 Distance between dipole center and liquid 15.0 mm Area scan resofution dx=$mm/dy=8mm Zoon Scan Resolution dx=8mm/dy=8mm/dz=5mm Frequency $35 MBz Input power 20 dBm Liquid Temperature 2A °C Lab Temperature 2 °C Lab Humidity 45 % Frequency 1 g SAR (W/kg/W) 10 g SAR (W/kg/W) MHz measured measured 835 9.83 (0.98) 6.45 (0.64) cammmm Sutee csmine renos Stetzee wa es takm BB (we 22 (85 t s tioe fiod san fwigl i tatiet a 2 & & m m F7 Xtent C vie Zima) Page: 10/11 This document shall not be reproduced, except in full orin part, without the written approval ofMVG. The information contained herein is to be used only forthe purposeforwhich it is submitted and is not to be released in whole orpart withoutwritten approval ofMVG.

NT Certificate #4298.01 SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.100.2.18.SATU.A 8 LIST OF EQUIPMENT Equipment Summary Sheet Equipment Manufacturer / . a Current Next Calibration Description Model ocsnn Calibration Date Date (Validated. No cal Validated. No cal SAM Phantom MVG SN—20,/09—SAM71 required. required. |COMOSAR Test Bench| Version 3 NA Validated. required. No cal Validated. required. No cal Network Analyzer Rh°4® g‘ViCh""a'Z SN100132 0212016 0222019 Calipers Carrera CALIPER—01 01/2017 01/2020 Reference Probe MVG EPG122 SN 18711 10/2017 10/72018 Multimeter Keithley 2000 1188656 01/2017 01/2020 Signal Generator Agilent E4438C MY49070581 01/2017 01/2020 Amplifier Aethercomm SN 046 Characterized pri_or to |Characterized pripr to test. No cal required. |test. No cal required. Power Meter HP E4418A US38261498 01/2017 01/2020 Power Sensor HP ECP—E26A US37181460 01/2017 01/2020 Directional Coupler Narda 4216—20 o1386 Characterized prior to Characterized prior to test. No cal required. |test. No cal required. Temperature and Humidity Sensor Control Company 150798832 11/2017 11/2020 Page: 11/11 This document shall not be reproduced, exceptin full orin part, without the written approval ofMVG. The information contained herein is to be used onlyfor the puposefor whichit is submitted and is not to be released in whole or part without wnitten approval ofMVG.

NTEKIEIW & ®a Certificate #4258.01 ~ SAR Reference Dipole Calibration Report Ref : ACR.109.5.18.SATU.A SHENZHEN NTEK TESTING TECHNOLOGY CO., LTD. BUILDING E, FENDA SCIENCE PARK, SANWEI COMMUNITY, XIXIANG STREET, BAO‘AN DISTRICT, SHENZHEN GUANGDONG, CHINA MVG COMOSAR REFERENCE DIPOLE FREQUENCY: 1900 MHZ SERIAL NO.: SN 03/15 DIP 1G900—350 Calibrated at MVG US 2105 Barrett Park Dr. — Kennesaw, GA 30144 &n 4* (accrepitrep ds caitetioncert szzsear Calibration Date: 04/19/2018 Summary: This document presents the method and results from an accredited SAR reference dipole calibration performed in MVG USA using the COMOSAR test bench. All calibrationresults are traceable to national metrology institutions.

NTEKJEiW* (acereviteo) Certificate #4258.01 ~ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.109.5.18.SATUA Name Function Date Signature — z2 Prepared by : Jérome LUC Product Manager 4/19/2018 27 Checked by : Jérome LUC Product Manager 4/19/2018 g%/ Approved by : Kim RUTKOWSKI Quality Manager 4/19/2018 hum Puthowihd Customer Name SHENZHEN NTEK Distribution — TESTNG istripunon . TECHNOLOGY CO., LTD. Issue Date Modifications A 4/19/2018 Initial release Page: 2/11 This document shall not be reproduced, except in full or m part, without the written approval ofMVG. The information contained herein is to be used ontyfor the purpose for which it is submitted and is not to be released in whole or part without written approval ofMVG.

NTEKIE:W © (accrepiteo Certificate #4258.01 ~ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.109.5.18.SATUA TABLE OF CONTENTS oooo e 4 |DESCs SnnEol e 4 o Product Description .... .4 w 3.1 General Information 4 hoEontstC e 5 4.1 Return Loss Requirements 5 4.2 Mechanical Requirements 5 hoEesontsl Optsecnn e 5 5.1 Return Loss 5.2 Dimension Measurement 5 5.3 Validation Measurement 5 eniMoatstoriiEnsmentoul enen 6 6.1 Return Loss and Impedance In Head Liquid 6 6.2 Return Loss and Impedance In Body Liquid 6 6.3 Mechanical Dimensions 6 METTeon ntcmeooe 7 7.1 Head Liquid Measurement 7 7.2 SAR Measurement Result With Head Liquid 8 7.3 Body Liquid Measurement 9 7.4 SAR Measurement Result With Body Liquid 10 LiSt Of EQUIDMEDE :.2 2.00 0000000000000 enc ncnm en en en n en n e vev en rev en en mm mc 11 go Page: 3/11 This documentshall not be reproduced, except in full orin part, without the written approval ofMVG. The information contained herein is to be used onlyfor the purpose for which it is submitted and is not to be released in whole or part without written approval ofMVG.

«9 "nln"" cortificate #4298.01 ~ mVG SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.109.5.18.SATU.A 1 INTRODUCTION This document contains a summary of the requirements set forth by the IEEE 1528, FCC KDBs and CEMIEC 62209 standards for reference dipoles used for SAR measurement system validations and the measurements that were performed to verifythat the product complies with the fore mentioned standards. 2 DEVICE UNDER TEST Device Under Test Device Type COMOSAR 1900 MHz REFERENCE DIPOLE Manufacturer MVG Model $1D1900 Scrial Number SN 03/15 DIP 1G900—350 Product Condition (new / used) Used A yearly calibration interval is recommended. 3 PRODUCT DESCRIPTION 34 GENERAL INFORMATION MVG‘s COMOSAR Validation Dipoles are built in accordance to the IEEE 1528, FCC KDBs and CELIIEC 62209 standards. The product is designed for use with the COMOSAR test bench only. Figure 1 — MVG COMOSAR Validation Dipole Page: 4/11 This document shall not be reproduced, except in full or in part, without the written approval ofMVG. The information contained herein is to be used onlyfor the purposefor whichit is submitted and is notto be released in whole orpart without written approval ofMVG.

NTEKJL:JJ*=« KA Certificate #4298.01 ~ mvG SAR REFERENCE DIPOLE CALIBRATION REPORT Ref ACR109.5.18.SATU.A 4 MEASUREMENT METHOD The IEEE 1528. FCC KDBs and CEIIEC 62209 standards provide requirements for reference dipoles used for system validation measurements. The following measurements were performed to verify that the product complies with the fore mentioned standards. 4.1 RETURN LOSS REQUIREMENTS The dipole used for SAR system validation measurements and checks must have a return loss of —20 dB or better. The return loss measurement shall be performed against a liquid filled flat phantom. with the phantom constructed as outlined in the fore mentioned standards. 4.2 MECHANICAL REQUIREMENTS The IEEE Std. 1528 and CEIIEC 62209 standards specify the mechanical components and dimensions of the validation dipoles. with the dimensions frequency and phantom shell thickness dependent. The COMOSAR test bench employs a 2 mm phantom shell thickness therefore the dipoles sold for use with the COMOSAR test bench comply with the requirements set forth for a 2 mm phantom shell thickness. 5 MEASUREMENT UNCERTAINTY All uncertainties listed below represent an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2, traceable to the Internationally Accepted Guides to Measurement Uncertainty. 5.1 RETURNLOSS The following uncertainties apply to the return loss measurement: Frequency band Expanded Uncertainty on Return Loss 400—6000MHz 0.1 dB 5.2 DIMENSION MEASUREMENT The following uncertainties apply to the dimension measurements: Length (mm) Expanded Uncertainty on Length 3 — 300 0.05 mm 5.3 VALIDATION MEASUREMENT The guidelines outlined in the IEEE 1528 FCC KDBs. CENELEC ENS50361 and CEMIEC 62209 standards were followed to generate the measurement uncertainty for validation measurements. Scan Volume Expanded Uncertainty 1g 20.3 % Page: 5/11 This documentshall not be reproduced, except infull orin part, without the written approval ofMVG. The information contained herein is to be used only for the purpose for which it is submitted and is not to be released in whote or part without written approval ofMVG.

NTEKIE:W Certificate #4258.01 SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.109,5.18.SATU.A 10 g 20.1 % 6 CALIBRATION MEASUREMENT RESULTS 6.1 RETURN LOSS AND IMPEDANCE IN HEAD LIQUID Frequency, MHz 1880 1900 1920 1940 1960 1980 2000 S11, 48 «59— Frequency (MHz) Return Loss (dB) Requirement (dB) Impedance 1900 —25.15 —20 52.6 Q + 5.1 jQ 6.2 RETURN LOSS AND IMPEDANCE IN BODY LIQUID Frequency. MHz 1900 1920 1940 19%0 S11, 48 Frequency (MHz) Return Loss (dB) Requirement (dB) Impedance 1900 —22.99 —20 47.6 Q + 6.5 jQ 6.3 MECHANICAL DIMENSIONS Frequency MHz L mm h mm d mm required measured required measured required measured 300 420.0 +1 %. 250.0 41 %. 6.35 41 %. Page: 6/11 This documentshall not be reproduced, except in full orin part, without the written approval ofMVG. The information contained herein is to be used onlyfor the purpose for which it is submitted and is not to be released in whole or part without written approval of MVG.

NTEKIE:W (accrepiteo) Certificate #4258.01 ~ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.109.5.18.SATUA aso 290.0 41%. 166.7 +1 %. 635 +1 %. 750 176.0 41 %. 100.0 +1 %. 635 +1 %. 835 161.0£1%. 80.8 +1 %. 3.641%. 900 149.0 £1%. 83.3 +1 %. 3.611%. 1450 89.1 +1 %. 51.7 +1 %. 3.611%. 1500 80.5 +1 %. 50.0 1 %. 3.621%. 1640 79.0 +1 %. 45.7 +1 %. 3.641%. 1750 75.2 41 %. 42.9 +1 %. 3.641%. 1800 72.0 +1 %. 41.7 +1 %. 3.641%. 1900 68.0 +1 %. pass 39.5 +1 %. PaS$ 3.6+1%. PaSS 1950 66.3 +1 %. 38.5 +1 %. 3.641%. 2000 64.5 +1 %. 37.5 +1 %. 3.641%. 2100 61.0 +1 %. 35.7 +1 %. 3.6+1%. 2300 55.5 +1 %. 32.6 +1 %. 3.6+1%. 2450 51.5 41 %. 30.4 +1 %. 3.641%. 2600 48.5 +1 %. 28.8 +1 %. 3.641%. 3000 41.5 +1 %. 25.0 +1 %. 3.641%. 3500 37.01%. 26.4 +1 %. 3.641%. 3700 34.721%. 26.4 +1 %. 3.641%. 7 VALIDATION MEASUREMENT The IEEE Std. 1528. FCC KDBs and CEUIEC 62209 standards state that the system validation measurements must be performed using a reference dipole meeting the fore mentioned return loss and mechanical dimension requirements. The validation measurement must be performed against a liquid filled flat phantom, with the phantom constructed as outlined in the fore mentioned standards. Per the standards, the dipole shall be positioned below the bottom of the phantom, with the dipole length centered and parallel to the longest dimension of the flat phantom., with the top surface of the dipole at the described distance from the bottom surface of the phantom. 7.1 HEAD LIQUID MEASUREMENT Fre’(\],ll:-‘elncy Relative permittivity (€,") Conductivity (0) 5/m required measured required measured 300 45.3 15 % 0.87 15 % 450 43.5 15 % 0.87 15 % 750 41.9 15 % 0.89 15 % 835 41.5 15 % 0.90 15 % 900 41.5 15 % 0.97 25 % 1450 40.5 15 % 1.20 25 % 1500 40.4 15 % 12315 % 1640 40.2 15 % 13115 % 1750 40.1 15 % 1.37 35 % Page: 7/11 This documentshall not be reproduced, except in full orin part, without the written approval ofMVG. The information contained herein is to be used onlyfor the purpose for which it is submitted and is not to be released in whole or part without written approval ofMVG.

NTEKIE:W (accrepiteo) Certificate #4258.01 SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.109.5.18.SATUA 1800 40.0 15 % 140 25 % 1900 40.0 15 % PASS 140 25 % PASS 1950 40.0 15 % 1.40 25 % 2000 40.0 15 % 1.40 25 % 2100 30.8 15 % 1.49 25 % 2300 39.5 125 % 1.67 25 % 2450 39.2 125 % 1.80 25 % 2600 39.0 15 % 1.96 15 % 3000 38.5 15 % 2.40 15 % 3500 37.9 15 % 2.91 15 % 7.2 SAR MEASUREMENT RESULT WITH HEAD LIQUID The IEEE Std. 1528 and CEIMIEC 62209 standards state that the system validation measurements should produce the SAR values shown below (for phantom thickness of 2 mm). within the uncertainty for the system validation. All SAR values are normalized to 1 W forward power. In bracket. the measured SAR is given with the used input power. Software OPENSAR V4 Phantom SN 20/09 SAM71 Probe SN 18/11 EPG122 Liquid Head Liquid Values: eps‘ : 38.5 sigma : 1.45 Distance between dipole center and liquid 10.0 mm Area scan resolution. dx=$mm/dy=8mm Zoon Scan Resolution dx=8mm/dy=8mm/dz=5mm Frequency 1900 MHz Input power 20 dBm Liquid Temperature 21 °C Lab Temperature 21 °C Lab Humidity 45 % F'e;‘:’z"q 1 g SAR (W/kg/w) 10 g SAR (W/kg/w) required measured required measured 300 2.85 1.94 450 4.58 3.06 750 849 5.55 835 9.56 6.22 900 10.9 6.99 1450 29 16 1500 30.5 16.8 1640 34.2 18.4 1750 36.4 19.3 1800 38.4 20.1 Page: 8/11 This documentshall not be reproduced, except in full orin part, without the written approval ofMVG. The information contained herein is to be used onlyfor the purpose for which it is submitted and is not to be released in whole or part without written approval ofMVG.

NTEKIE:W [accreoiteo) Certificate #4258.01 ~ ‘ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref ACR.109.5.18.SATUA 1900 39.7 38.92 (3.89) 20.5 20.09 (2.01) 1950 40.5 20.9 2000 41.1 211 2100 43.6 21.9 2300 48.7 23.3 2450 524 24 2600 55.3 24.6 3000 63.8 25.7 3500 67.1 25 3700 67.4 24.2 m mmz Sulee Pufisibunts Reena Bm ' d crum ds 1e ies a fase lhe e Mn se C s s Zontum & 2‘ us > 33 m > . 1 w Gre h e e e k d nas—, . ___A_____J] i m ns n 2 a ® m d F7 xt C v l Zine) 7.3 BODY LIQUID MEASUREMENT Frequent I?IIHz Y Relative permittivity (€;‘) Conductivity (0) 5/m required measured required measured 150 61.9 45 % 0.80 +5 % 300 58.2 15 % 0.92 15 % 450 56.7 25 % 0.94 25 % 750 55.5 15 % 0.96 15 % 835 55.2 15 % 0.97 15 % 900 55.0 25 % 1.05 £5 % 915 55.0 15 % 1.06 15 % 1450 54.0 15 % 1.30 £5 % 1610 53.8 15 % 1.40 £5 % 1800 53.3 25 % 1.52 25 % 1900 53.3 15 % PASS 1.52 15 % PASS 2000 53.3 15 % 1.52 15 % 2100 53.2 25 % 1.62 £5 % Page: 9/11 This document shall not be reproduced, except in fill orin part, without the writien approval ofMYG. The information contained herein is to be used onlyfor the purposefor which it is submitted and is not to be released in whole or part withoutwitten approval ofMVG.

NTEKIE:W [accreoiteo) Certificate #4258.01 SAR REFERENCE DIPOLE CALIBRATION REPORT Reff ACR.109.5.18.SATUA 2300 52.9 15 % 1.81 25 % 2450 52.7 125 % 1.95 25 % 2600 52.5 15 % 2.16 45 % 3000 52.0 15 % 2.73 15 % 3500 51.3 15 % 3.31 45 % 3700 51.0 25 % 3.55 15 % 5200 49.0 £10 % 5.30 210 % 5300 48.9 £10 % 5.42 10 % 5400 48.7 £10 % 5.53 10 % 5500 48.6 +10 % 5.05 110 % 5600 48.5 £10 % 5.77 110 % 5800 48.2 110 % 6.00 £10 % 7.4 SAR MEASUREMENT RESULT WITH BODY LIQUID Software OPENSAR V4 Phantom SN 20/09 SAM71 Probe SN 18/11 EPG122 Liquid Body Liquid Values: eps® : 53.3 sigma : 1.56 Distance between dipole center and liquid 10.0 mm Area scan resolution. dx=8mm/dy=8mm Zoon Scan Resolution dx=8mm/dy=8mm/dz=S5mm Frequency 1900 MHz Input power 20 dBm Liquid Temperature 21 °C Lab Temperature 21 °C Lab Humidity 45 % Frequency 1 g SAR (W/kg/w) 10 g SAR (W/ke/w) MHz measured measured 1900 39.02 (3.90) 20.57 (2.06) ermamcmmee Sutce Rrourineas Reesoa Gini MX san twhgl use c ho a e a o4 asr— J 6 3 4 606 an rr meas de 2b 2e 2e ts ce mb C atenl C vieed Zm Page: 10/11 This documentshall not be reproduced, except in full orin part, without the written approval ofMVG. The information contained herein is to be used ontyfor the purpose for which it is submitted and is not to be released in whole or part without written approval ofMVG.

NT Certificate #4298.01 us SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR109.5.18.SATUA 8 LIST OF EQUIPMENT Equipment Summary Sheet Equipment Manufacturer / Identification No Current Next Calibration Description Model ‘| Calibration Date Date alidated. No cal Validated. No cal SAM Phantom MVG SN—20,/09—SAM71 required. required. . alidated. No cal Validated. No cal |COMOSAR Test Bench Version 3 NA required. required. Network Analyzer Rhode 8Schwarz sN100132 0272016 022019 Calipers Carrera CALIPER—01 01/2017 01/2020 Reference Probe MVG EPG122 SN 18711 10/2017 10/2018 Multimeter Keithley 2000 1188656 01/2017 01/2020 Signal Generator Agilent E4438C MY49070581 014/2017 01/2020 t Characterized prior to |Characterized prior to Amplifier Aethercomm Sn 046 test. No cal required. |test. No cal required. Power Meter HP E4418A US38261498 01/2017 01/2020 Power Sensor HP ECP—E26A US37181460 01/2017 01/2020 Directional Coupler Narda 4216—20 o1386 Characterized pri_or to |Characterized pri_or to test. No cal required. |test. No cal required. Temperature 2nd Humidity Sensor control Company 150798832 1172017 1172020 Page: 11/11 This document shall not be reproduced, except m full orin part, without the written approval ofMVG. The information contained herein is to be used onlyfor the purposefor which it is submitted and is not to be released in whole orpart without written approval of MVG.

NTEKJE:W [accreoiteo) Certificate #4258.01 ~ SAR Reference Dipole Calibration Report Ref : ACR.109.7.18.SATU.A SHENZHEN NTEK TESTING TECHNOLOGY CO., LTD. BUILDING E, FENDA SCIENCE PARK, SANWEI COMMUNITY, XIXTIANG STREET, BAO‘AN DISTRICT, SHENZHEN GUANGDONG, CHINA MVG COMOSAR REFERENCE DIPOLE FREQUENCY: 2450 MHZ SERIAL NO.: SN 03/15 DIP 2G450—352 Calibrated at MVG US 2105 Barrett Park Dr. — Kennesaw, GA 30144 s 19e wA/z in+ @3 i?laezme‘/—-\k zzzZnS Arrliil aie® (aecrepirep) cxivetioncent azzesor Calibration Date: 04/19/2018 Summary: This document presents the method and results from an accredited SAR reference dipole calibration performed in MVG USA using the COMOSAR test bench. All calibrationresults are traceable to national metrology institutions.

NTEKIE:W °_ {accrepiteo) Certificate #4258.01 ~ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.109.7.18.SATUA Name Function Date Stgnature Prepared by: Jérome LUC Product Manager 4/19/2018 j/%, Checked by: Jérome LUC Product Manager 4/19/2018 (73 Approved by: Kim RUTKOWSKT Quality Manager 4/19/2018 Jum PutthawsiPd Customer Name SHENZHEN NTEK pathoe: TESTING Distribution : TECHENOLOGY CO.. LTD. Issue Date Modifications A 4/19/2018 Initial release Page: 2/11 This document shall not be reproduced, except in full orin part, without the written approval ofMVG. The information contained herein is to be used onlyforthe purpose forwhich it is submitted and is not to be released in whole orpart without written approval ofMVG.

NTEKIE:W Accreviteo Certificate #4258.01 ~ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.109.7.18.SATUA TABLE OF CONTENTS TTOGUCHIOM...ccscece en cnncne enc nen en nnnnnnennnnnnnnnnn en en en en nnnnennenennnnenennnnennnnee en 4 DeViG@ UDG@T T@St ........sc lsncs iscc eencicnnennnnnnnnn mm nnnnnmnemnnnnenemnnnennnne e 4 PTOGUCt D@SCTIDMOM 12200000 000000000000 en eeeeeeeeeenenevene en venereneevenmennenemenneneneneene en nenee 4 3.1 General Information 4 4 MEASUPEMENt MEtAOG .....2....2000000000000000 00e cesc ecnemmnnenemnmmmnnnmnmenmnnee es 5 4.1 Return Loss Requirements 5 4.2 Mechanical Requirements 5 hoEeBenc hten e 5 5.1 Return Loss 5 5.2 Dimension Measurement 5 5.3 Validation Measurement 5 CalibratioMEASUT@MENt ReSUITS ............cscncsceceeeeeeneememmmmnmmmmmmnnmmmnen n 6 6.1 Return Loss and Impedance In Head Liquid 6 6.2 Return Loss and Impedance In Body Liquid 6 6.3 Mechanical Dimensions 6 VAIGANION IM@ASUT@MNE ........2....0000000000000000c0 0scc emenemmnmmmnnmnmenmnnee es 7 7.1 Head Liquid Measurement 7 7.2 SAR Measurement Result With Head Liquid 8 7.3 Body Liquid Measurement 9 7.4 SAR Measurement Result With Body Liquid 10 8 LiSt Of EQUIDI@M.220 0000000000000 eeeemeeeveeeeeeenenevvre en vererereeemmeenenmemnenenenene en ns 11 Page: 3/11 This document shall not be reproduced, except in full orin part, without the written approval ofMVG. The information contained herein is to be used onlyforthe purpose forwhich it is submitted and is not to be released in whole orpart without written approval ofMVG.

«m Sy/ NTEKJEiJJ+= «a Ti_ certificate#4298.01__* mvG SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.109.7.18.SATU.A 1 INTRODUCTION This document contains a summary of the requirements set forth by the IEEE 1528, FCC KDBs and CELIEC 62209 standards for reference dipoles used for SAR measurement system validations and the measurements that were performed to verify that the product complies with the fore mentioned standards. 2 DEVICE UNDER TEST Device Under Test Device Type COMOSAR 2450 MHz REFERENCE DIPOLE Manufacturer MVG Model $1D2450 Serial Number SN 03/15 DIP 2G6450—352 Product Condition (new / used) Used A yearly calibrationinterval is recommended. 3 PRODUCT DESCRIPTION 3.1 GENERAL INFORMATION MVG‘s COMOSAR Validation Dipoles are built in accordance to the IEEE 1528, FCC KDBs and CELIEC 62209 standards. The product is designed for use with the COMOSAR test bench only. Figure 1 — MVG COMOSAR Validation Dipole Page: 4/11 This document shall notbe reproduced, except in full orin part, without the written approval ofMVG. The information contained herein is to be used onlyforthe purposeforwhich it is submitted and is not to be released in whole orpart without witten approval ofMVG.

NTEKJL:JJ*=« KA Certificate #4298.01 ~ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.109.7.18.SATUA 4 MEASUREMENT METHOD The IEEE 1528, FCC KDBs and CELMIEC 62209 standards provide requirements for reference dipoles used for system validation measurements. The following measurements were performed to verify that the product complies with the fore mentioned standards. 4.1 RETURNLOSS REQUIREMENTS The dipole used for SAR system validation measurements and checks must have a return loss of —20 dB or better. The return loss measurement shall be performed against a liquid filled flat phantom, with the phantomconstructed as outlined in the fore mentioned standards. 4.2 MECHANICAL REQUIREMENTS The IEEE Std. 1528 and CEIMIEC 62209 standards specify the mechanical components and dimensions of the validation dipoles, with the dimensions frequency and phantom shell thickness dependent. The COMOSAR test bench employs a 2 mm phantom shell thickness therefore the dipoles sold for use with the COMOSAR test bench comply with the requirements set forth for a 2 mm phantomshell thickness. 5 MEASUREMENT UNCERTAINTY All uncertainties listed below represent an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. traceable to the Internationally Accepted Guides to Measurement Uncertainty. 5.1 RETURNLOSS The following uncertainties apply to the return loss measurement: Frequency band Expanded Uncertainty on Return Loss 400—6000MHz 0.1 dB 5.2 DIMENSION MEASUREMENT The following uncertainties apply to the dimension measurements: Length (mm) Expanded Uncertainty on Length 3 — 300 0.05 mm 53 VALIDATION MEASUREMENT The guidelines outlined in the IEEE 1528, FCC KDBs, CENELEC ENSO361 and CELIEC 62209 standards were followed to generate the measurement uncertainty for validation measurements. Scan Volume Expanded Uncertainty 1 g 20.3 % Page: 5/11 This document shall not be reproduced, except infull orin part, without the written approval ofMVG. The information contained herein is to be used onlyforthe purposeforwhich it is submitted and is not to be released in whole orpart without wnitten approval ofMVG.

NTEKIE:W Certificate #4258.01 SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.109.7.18.SATUA 10 g 20.1 % 6 CALIBRATION MEASUREMENT RESULTS 6.1 RETURN LOSS AND IMPEDANCE IN HEAD LIQUID Fequency, MHz 2380 2400 2420 2440 2460 2480 2500 2520 Frequency (MHz) Return Loss (dB) Requirement (dB) Impedance 2450 —28.15 —20 53.9 Q +0.3 jQ 6.2 RETURN LOSS AND IMPEDANCE IN BODY LIQUID Frequency, MHz 2400 2420 2440 2460 2480 2500 2520 anp— Frequency (MHz) Return Loss (dB) Requirement (dB) Impedance 2450 —22.99 —20 57.6 0 — 0.8 jQ 6.3 MECHANICAL DIMENSIONS Frequency MHz L mm h mm d mm required measured required measured required measured 300 420.0 +1 %. 250.0 41 %. 6.35 +1 %. Page: 6/11 This document shall not be reproduced, except in full orin part, without the written approval ofMVG. The information contained herein is to be used onlyforthe purpose forwhich it is submitted and is not to be released in whole orpart without written approval ofMVG.

NTEKJLiW *« Accreviteo) Certificate #4258.01 ~ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.109.7.18.SATU.A 450 290.0 +1 %. 166.7 +1 %. 6.35 41 %. 750 176.0 +1 %. 100.0 +1 %. 6.35 +1 %. 835 161.0 +1 %. 89.8 +1 %. 3.6 +1 %. 900 149.0 £1%. 83.3 :1 %. 3.6 41 %. 1450 89.1 +1 %. 51.7 41 %. 3.6 +1 %. 1500 80.5 £1 %. 50.0 41 %. 3.6 41 %. 1640 79.0 £1%. 45.7 41 %. 3.6 41 %. 1750 75.2 +1 %. 42.9 +1 %. 3.6 +1 %. 1800 72.0 £1%. 41.7 +1 %. 3.6 +1 %. 1900 68.0 £1%. 39.5 £1 %. 3.6 41 %. 1950 66.3 +1 %. 38.5 +1 %. 3.6 +1 %. 2000 64.5 +1 %. 37.5 41 %. 3.6 41 %. 2100 61.0 £1%. 35.7 +1 %. 3.6 +1 %. 2300 55.5 +1 %. 32.6 +1 %. 3.6 +1 %. 2450 51.5 #1%. pass 30.4 +1 %. PASS 3.6 +1 %. PASS 2600 48.5 +1 %. 28.8 +1 %. 3.6 +1 %. 3000 41.5 £1%. 25.0 +1 %. 3.6 41 %. 3500 37.041%. 264 +1 %. 3.6 41 %. 3700 34.7+1%. 264 +1 %. 3.6 +1 %. 7 VALIDATION MEASUREMENT The IEEE Std. 1528. FCC KDBs and CEMIEC 62209 standards state that the system validation measurements must be performed using a reference dipole meeting the fore mentioned return loss and mechanical dimension requirements. The validation measurement must be performed against a liquid filled flat phantom, with the phantom constructed as outlined in the fore mentioned standards. Per the standards. the dipole shall be positioned below the bottom of the phantom. with the dipole length centered and parallel to the longest dimension of the flat phantom, with the top surface of the dipole at the described distance fromthe bottomsurface ofthe phantom. 7.1 HEAD LIQUID MEASUREMENT Fre:/ll::l"w Relative permittivity (€;) Conductivity (0) 5/m required measured required measured 300 45.3 15 % 0.87 15 % 450 43.5 15 % 0.87 25 % 750 41.9 15 % 0.89 15 % 835 41.5 15 % 0.90 15 % 900 41.5 15 % 0.97 15 % 1450 40.5 15 % 1.20 15 % 1500 40.4 +5 % 1.23 #5 % 1640 40.2 25 % 131 15 % 1750 40.1 15 % 1.37 25 % Page: 7/11 This document shall not be reproduced, except in full orim part, without the written approval ofMVG. The information contained herein is to be used onlyforthe purposeforwhich it is submitted and is not to be released in whole orpart without written approval ofMVG.

NTEKIE:W (accrepiteo) Certificate #4258.01 SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.109.7.18.SATU.A 1800 40.0 15 % 1.40 45 % 1900 40.0 15 % 1.40 15 % 1950 40.0 15 % 1.40 15 % 2000 40.0 15 % 140 25 % 2100 39.8 15 % 1.49 25 % 2300 39.5 15 % 1.67 45 % 2450 39.2 15 % PASS 1.80 15 % PASS 2600 39.0 15 % 1.96 15 % 3000 38.5 15 % 2.40 25 % 3500 37.9 15 % 2.91 25 % 7.2 SAR MEASUREMENT RESULT WITH HEAD LIQUID The IEEE Std. 1528 and CEIIEC 62209 standards state that the system validation measurements should produce the SAR values shown below (for phantom thickness of 2 mm),. within the uncertainty for the systemvalidation. All SAR values are normalized to 1 W forward power. In bracket. the measured SAR is given with the used imput power. Software OPENSAR V4 Phantom SN 20/09 SAM7L Probe SN 18/11 EPG122 Liquid Head Liquid Values: eps‘ : 37.5 siginna : 1.80 Distance between dipole center and liquid 10.0 mm Area scan resolution dx=gmm/dy=8mm Zoon Scan Resolution dx=Smm/dy=Smm/dz=5mm Frequency 2450 MHz Input power 20 dBm Liquid Temperature 21 °C Lab Temperature 21 °C Lab Humidity 45 % F’e&':'l"“’ 1 g SAR (W/kg/W) 10 g SAR (W/kg/W) required measured required measured 300 2.85 1.94 450 4.58 3.06 750 8.49 5.55 835 9.56 6.22 900 10.9 6.99 1450 29 16 1500 30.5 16.8 1640 34.2 18.4 1750 36.4 19.3 1800 38.4 20.1 Page: 5/11 This document shall not be reproduced, except in full orim part, without the written approval ofMVG. The information contained herein is to be used onlyforthe purposeforwhich it is submitted and is not to be released in whole orpart without written approval ofMVG.

NTEKIE:W [accreoiteo) Certificate #4258.01 ~ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.100.7.18.SATU.A 1900 39.7 20.5 1950 40.5 20.9 2000 41.1 21.1 2100 43.6 21.9 2300 48.7 233 2450 524 53.76 (5.38) 24 2412 (2.41) 2600 55.3 24.6 3000 63.8 25.7 3500 67.1 25 3700 67.4 24.2 car Suiee sumerine tnke 3 92 1t ts 42 is s 12 ie 1005 TB 800 zantiss g €00— Ciges) a as o. § am « 200 CaRed a3r~, 1 0 406 to 12 14 16 18 & 22 M 26 20 t F7 mt BC view Zizel 7.3 BODY LIQUID MEASUREMENT Fre:;_le:w Relative permittivity (€)‘) Conductivity (0) S/m required measured required measured 150 61.9 +5 % 0.80 15 % 300 58.2 +5 % 0.92 25 % 450 56.7 +5 % 0.94 15 % 750 55.5 £5 % 0.96 15 % 835 55.2 45 % 0.97 15 % 900 55.0 +5 % 1.05 15 % 915 55.0 +5 % 1.06 15 % 1450 54.0 #5 % 1.30 +5 % 1610 53.8 +5 % 140 25 % 1800 53.3 45 % 1.52 15 % 1900 53.3 45 % 1.52 45 % 2000 53.3 15 % 1.52 15 % 2100 53.2 +5 % 1.62 +5 % Page: 9/11 This document shall not be reproduced, except in full orin part, without the written approval ofMVG. The information contained herein is to be used onlyfor the puposefor whichit is submitted and is not to be released in whole or part without writien approval ofMVG.

NTEKIE:W [accreoiteo) Certificate #4258.01 ~ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.109.7.18.SATU.A 2300 52.9 15 % 1.81 45 % 2450 52.7 15 % PASS 1.95 15 % PASS 2600 52.5 15 % 2.16 15 % 3000 52.0 15 % 2.73 25 % 3500 51.3 15 % 3.31 25 % 3700 51.0 15 % 3.55 15 % 5200 49.0 110 % 5.30 £10 % 5300 48.9 110 % 5.42 £10% 5400 48.7 210 % 5.53 £10% 5500 48.6 £10 % 5.65 £10% 5600 48.5 10 % 5.77 £10% 5800 48.2 110 % 6.00 £10 % 7.4 SAR MEASUREMENT RESULT WITH BODY LIQUID Software OPENSAR V4 Phantom SN 20/09 SAMT7L Probe SN 18/11 EPG122 Liquid Body Liquid Values: eps® : 53.2 sigma : 1.89 Distance between dipole center and liquid 10.0 mm Area sean resolution dx=8mm/dy=8mm Zoon Scan Resolution dx=Smm/dy=Smm/dz=5mm Frequency 2450 MHz Input power 20 dBm Liquid Temperature 21 °C Lab Temperature 21 °C Lab Humidity 45 % F 'e&':"l"“’ 1 g SAR (W/ke/W) 10 g SAR (W/ke/W) measured measured 2450 52.90 (5.29) 24.09 (2.41) pxmmmrencem Sutne masemine zenions Steite re o se son wl ® SB d @ infe $ # SE[I*\ 2t tm a00 contecs ede 2 & gdfll} |Y N 20 ~] t—— oan— 4 i $ 2 a fructia c nc a o F7 xt BC Y Z(mn) Page: 10/11 This document shall not be reproduced, except in full orim part, without the written approval ofMVG. The information contained herein is to be used onlyforthe purposeforwhich it is submitted and is not to be released in whole orpart without written approval ofMVG.

NT Certificate #4298.01 (LDuS SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.109.7.18.SATUA 8 LIST OF EQUIPMENT Equipment Summary Sheet Equipment Manufacturer / a & Current Next Calibration Description Model Miontiicationine Calibration Date Date , Validated. No cal Validated. No cal SAM Phantom MVG SN—20/09—SAM71 required. required. COMOSAR Test Bench] Version 3 NA Validated. required. No cal |Validated. required. No cal Network Analyzer Rh"deg‘vid‘warz sN100132 0272016 022019 Calipers Carrera CALIPER—01 01/2017 01/2020 Reference Probe MVG EPG122 SN 18711 10/2017 10/2018 Multimeter Keithley 2000 1188656 01/2017 01/2020 Signal Generator Agilent E4438C MY49070581 01/2017 01/2020 Amplifier Aethercomm SN 046 Characterized pris)r to Characterized pripr to test. No cal required. |test. No cal required. Power Meter HP E4418A US38261498 01/2017 01/2020 Power Sensor HP ECP—E26A US37181460 01/2017 01/2020 Directional Coupler Narda 4216—20 o1s8s Characterized prior to |Oharacterized prior to test. No cal required. |test. No cal required. Temperature and Humidity Sensor Control Company 150798832 1172017 11/2020 Page: 11/11 This document shall not be reproduced, except in full orin part, without the written approval ofMVG. The information contained herein is to be used onlyforthe purpose forwhich it is submitted and is not to be released in whole orpart without written approval ofMVG.


Document Created: 2019-04-29 00:34:13
Document Modified: 2019-04-29 00:34:13
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC