system description

1103-EX-ST-2014 Text Documents

Raytheon Integrated Defense Systems

2014-12-05ELS_156630

A
TABLE OF CONTENTS

1.0 General Description...............................................................................................................1
1.1 Related Submittal(s) Grants..........................................................................................1
1.2 Product Description.....................................................................................................1
1.3 Test Methodology .......................................................................................................2
1.4 Test Facility................................................................................................................2

2.0 System Test Configuration ....................................................................................................3
2.1 Justification.................................................................................................................3
2.2 EUT Exercising Software.............................................................................................3
2.3 Special Accessories......................................................................................................3
2.4 Equipment Modification...............................................................................................3
2.5 Support Equipment List and Description........................................................................3
2.6 Test Configuration Block Diagram ................................................................................4

3.0 Test Results ...........................................................................................................................5
3.1 RF Power Output........................................................................................................6
3.2 Occupied Bandwidth ................................................................................................. 17
3.3 Spurious Emissions at Antenna Terminal..................................................................... 28
3.4 Out of Band Spurious Emissions at Antenna Terminal.................................................. 30
3.5 Field Strength of Spurious Emissions........................................................................... 38
3.6 Frequency Stability.................................................................................................... 41
3.7 Field Strength Calculation........................................................................................... 48

4.0 Test Equipment ................................................................................................................... 44

EXHIBIT I
Test Set Up Photographs ....................................................................................................... 45

EXHIBIT II
FCC ID Label Location ......................................................................................................... 50

EXHIBIT III
External Photographs............................................................................................................. 51

EXHIBIT IV
Internal Photographs.............................................................................................................. 54

EXHIBIT V
Electrical Schematics and Block Diagram ................................................................................ 62

EXHIBIT VI
User Manual and Operational Description................................................................................ 63

A
1.0 GENERAL DESCRIPTION

1.1 Related Submittals Grants

This is single application of the IT2611RF Module for Certification under FCC Part 90, Subpart M.
There are no other simultaneous applications.

1.2 Product Description

Purpose of the IT2611 RF Module

The IT2611 RF Module is a part of the non-multiratelation Location and Monitoring Service (LMS)
System. The IT2611 RF Module is mounted with antennas. The intended use of the IT2611 RF Module
unit is to generate a RF signal upon command from a reader, and deliver the signal to one of the antennas
for transmission and receive the reflected modulated tag signal returned through the antenna(s). Then
IT2611 RF Module demodulates, amplifies, and filters the received tag signal, and forwards the digital data
to the reader for processing. The IT2611 RF Module powered at 120VAC/60Hz through the external power
adapter manufactured by TransCore.

The IT2611 RF Module Transmitter

The IT2611 RF Module Transmitter operates in frequency ranges with type of modulation:

Uplink Mode (CW only):
From 902.25 to 903.75MHz (Continuous Wave, N0N Emission Modulation Designator) and
From 910.00 to 921.75MHz (Continuous Wave, N0N Emission Modulation Designator),
adjustable in 0.25MHz step.

Down link Mode (Digital modulation only):
From 912.75 to 918.75MHz (Manchester encode 300kbps Modulated Signal, L1D Emission Modulation
Designator), adjustable in 0.25MHz step.

Operating Power Level:

1 Watt maximum (30dBm) and may be attenuated up to 15dB with 1dB step

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 1 of 63

A
The IT2611 RF Module Antennas

Two different antennas could be used to transmit RF signal from the IT2611 RF Module:

AA3152 Universal Toll Antenna (UTA)

Frequency range: 902 to 928MHz
Gain: 13dBi
Impedance: 50Ohms

AA3153 Toll Antenna

Frequency range: 902 to 928MHz
Gain: 10.5dBi
Impedance: 50Ohms

The IT2611 RF Module Receiver

The IT2611 RF Module Receiver is a three-channel differential receiver with pre-amplifier. The power at the
receiving antenna terminal is not exceed 2.0 nanowatts.

1.3 Test Methodology

Emission measurements were performed according to the procedures in specified by ANSI/TIA/EIA-603-1992.
All field strength radiated emissions measurements were performed in the semi-anechoic chamber using a
substitution antenna method. All field strength radiated tests were performed at an antenna to EUT distance
of 3 meters, unless stated otherwise in the "Justification Section" of this Application.

1.4 Test Facility

The test site facility used to collect the radiated and conducted measurement data is located at 7250 Hudson
Blvd., Suite 100, Oakdale, Minnesota. This test facility has been fully described in a report dated on January
2000 submitted to your office. Please reference the site registration number: 90706, dated May 19, 2000.

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 2 of 63

A
2.0 SYSTEM TEST CONFIGURATION

2.1 Justification

FCC Part 90.210(k)(4) specifies measurements at LMS Sub-Band edges FCC Part 90.210(k)(6) for a non-
multilateration transmitter using 100kHz RBW. However, based on the rules interpretations provided by
TransCore in reference to the FCC Letter dated on June 9, 1997 (uploaded with application) measurements of
the Out-of-Band emissions with center frequencies within 1MHz from the band edges were taken using 300Hz
RBW (See Section 3.4).

2.2 EUT Exercising Software

The IT2611 RF Module was tested in the continuous transmission mode.

2.3 Special Accessories

There are no special accessories necessary for compliance of these products.

2.4 Equipment Modification

No modifications were installed during the testing.

2.5 Support Equipment List and Description

BSI Computer, s/n BSI1023175
Data Interface unit manufactured by TransCore
1611A BK Precision DC Power Supply, s/n 241-00988

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 3 of 63

A
3.0 TEST RESULTS

Data is included of the worst case configuration (the configuration which resulted in the highest emission levels).
A sample calculation, configuration photographs, data tables and graphical representations of the emissions are
included.

The EUT is intended for operation under the requirements of Part 90 (Subpart I and M), Part 15 (Subpart B).
Specific test requirements include the following:

47 CFR 90.205(j), 2.1046 RF Power Output
47 CFR 90.209(b)(5), 2.1049 Occupied Bandwidth
47 CFR 90.210(k)(3)(ii), 2.1051 Spurious Emissions at Antenna Terminal
47 CFR 90.210(k)(3)(ii), 2.1051 Out of Band Spurious Emissions at Antenna Terminals
47 CFR 90.210(k)(3)(ii), 2.1053 Field Strength of Spurious Radiation
47 CFR 90.213(a), 2.1055 Frequency Stability

The EUT does not re-modulate or re-key the signal. Based on the lack of re-keying/re-modulation circuitry, the
following test was not performed:

47 CFR 90.211, 2.1047 RF Modulation Characteristics

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 5 of 63

A
3.1 RF Power Output, FCC 90.205(j), 2.1046

RF Output measurements were made in the start, center, and end frequency of each frequency range with
appropriate type of modulation for these frequency ranges. The follow frequency ranges are used in the
EUT:

Uplink Mode:
From 902.25 to 903.75MHz (Continuous Wave Emission Designator)
From 910.00 to 921.75MHz (Continuous Wave Emission Designator),

Downlink Mode
From 912.75 to 918.75MHz (Modulated Signal Emission Designator, digital modulation, 300kbps,
Manchester code).

So, RF Output measurements were made for frequencies:
902.25MHz, CW
903.00MHz, CW
903.75MHz, CW
910.00MHz, CW
915.75MHz, CW
921.50MHz, CW
912.75MHz, Modulated
915.75MHz, Modulated
918.75MHz, Modulated

Test Procedure

The RF Power Output for the device was measured at the maximum power transmission condition. The
transmitter antenna port was connected to the Spectrum analyzer via the attenuator.

Total Power was calculated from Measured Power adding 6.2dB factor of the external-of-analyzer
attenuator.

Maximum Output Power at Antenna Terminal calculation
According to the FCC 90.205(j), the maximum ERP output power is 30 Watts (44.77dBm).
Maximum output power at antenna terminal = Max ERP Power – Antenna Gain = 44.77dBm – 13dBi
Maximum output power at antenna terminal = 31.77dBm
According to the client specification, the maximum output power at antenna terminal is 1 Watt, or 30dBm.
As a worse case, 30dBm output power at antenna terminal is chosen as a reference level of the Maximum
Output Power at antenna terminal.

Table and graphs below show the RF Power Output at antenna terminal.
Note: Emission level shown in the Graphs does not include 6.2dB attenuation factor of the attenuator.

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 6 of 63

A
RF Power Output Date: 01-03-2002
Company: TransCore
Model: IT2611
Test Engineer: Norman Shpilsher
Special Config. Info: The EUT antenna terminal was connected to the Spectrum
Analyzer through the attenuator 6.2dB (including cable loss).
Standard: FCC Part 90.205(j) and Part 2.1046

Table # 3-1-1

Output Measured Total Total Maximum Margin
Freq. Power Power Power Power Comments
MHz dBmV dBmV dBm dBm dB
902.25 (CW) 129.8 136.0 29.0 30.0 -1.0
903.00 (CW) 129.4 135.6 28.6 30.0 -1.4
903.75 (CW) 129.7 135.9 28.9 30.0 -1.2

910.00 (CW) 129.7 135.9 28.9 30.0 -1.1
915.75 (CW) 130.2 136.4 29.4 30.0 -0.6
921.50 (CW) 130.3 136.5 29.5 30.0 -0.5

912.75 (Mod) 129.6 135.8 28.8 30.0 -1.2
915.75 (Mod) 129.5 135.7 28.7 30.0 -1.3
918.75 (Mod) 129.7 135.9 28.9 30.0 -1.1

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 7 of 63

A
3.2 Occupied Bandwidth, FCC 90.209(b)(5), 2.1049

Occupied Bandwidth measurements were made for frequencies 902.25MHz, 903.0MHz, 903.75MHz,
910.0MHz, 915.75MHz, and 921.5MHz with unmodulated signal (CW) and for frequencies 912.75MHz,
915.75MHz, and 918.75MHz with modulated RF signal.

Test Procedure

The Occupied Bandwidth for the device was measured at the maximum power transmission condition. The
transmitter antenna port was connected to the Spectrum analyzer via the attenuator. The Occupied
Bandwidth was measured based on the analyzer 99% power measurement option.

The measured Occupied Bandwidth was compared with the maximum allowed bandwidth of 2MHz in
frequency range from 902 to 904MHz and 12MHz in frequency range 909.75 to 921.75MHz according to
FCC 90.209(b)(5).

Table and graphs below show the Occupied Bandwidth test result.
Note: Emission level shown in the Graphs does not include 6.2dB attenuation factor of the attenuator.

According to FCC 2.202 and type of modulation, the Necessary Bandwidth was determined from the
Occupied Bandwidth measurements (See Table # 3-2-1).

The Necessary Bandwidth is:

850Hz - for unmodulated signal (240KN0N Emissions Designator)

1.025MHz – for modulated signal (1M03L1D Emissions Designator)

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 17 of 63

A
Occupied Bandwidth Date: 01-03-2002
Company: TransCore
Model: IT2611
Test Engineer: Norman Shpilsher
Special Config. Info: The EUT antenna terminal was connected to the Spectrum
Analyzer through the attenuator 6.2dB (including cable loss).
Standard: FCC Part 90.209(b)(5) and Part 2.1049

Table # 3-2-1

Output Measured Bandwidth Maximum
Freq. with 99% Power Bandwidth Test Result
MHz kHz MHz
902.25 (CW) 0.80 2.0 Pass
903.00 (CW) 0.85 2.0 Pass
903.75 (CW) 0.85 2.0 Pass
910.00 (CW) 0.85 12.0 Pass
915.75 (CW) 0.85 12.0 Pass
921.50 (CW) 0.85 12.0 Pass
912.75 (Mod) 1020 12.0 Pass
915.75 (Mod) 1010 12.0 Pass
918.75 (Mod) 1025 12.0 Pass

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 18 of 63

A
3.3 Spurious Emissions at Antenna Terminal, FCC 90.210(k)(3)(ii), 2.1051

Spurious Emissions at antenna terminal was measured in frequency range up to 10 GHz (10th harmonic).

Test Procedure

The Spurious Emissions at Antenna Terminal for the device was measured at the maximum power
transmission condition. The transmitter antenna port was connected to the Spectrum analyzer via the
attenuator.

Total Emissions level was calculated from Measured Power adding 6.2dB of the external-of-analyzer
attenuator.

The Minimum Emission Attenuation calculation
The minimum emissions attenuation was calculated using the maximum output power P (Watt):
Minimum Attenuation = 55 + 10log (P)
The maximum measured output power in Section 3.1 is 29.5dBm, or 0.891 Watt
According to the client specification, the maximum output power at antenna terminal is 1 Watt, or 30dBm.
As a worse case, the Minimum Attenuation based on 1Watt maximum output power is chosen as a
reference level:
Minimum Attenuation = 55 + 10log (P) = 55 + 10log(1Watt) = 55dB

No spurious or harmonics emissions were observed at antenna terminal in frequency range up to 10GHz
(10th harmonic).

Graph below shows the spurious emissions at antenna terminal.
Note: Emission level shown in the Graphs does not include 6.2dB attenuation factor of the attenuator.

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 28 of 63

A
Graph # 3-3-1

Radiated Emissions at Antenna Terminal, FCC 90.210(k)
Job # - 3011655
Serial # - Line_1
Peak @ 915.75MHz = 130.5dBuV
Resolution Bandwidth 100kHz, Video Bandwidth 100kHz Line_1_t12
Model Number - IT2611
FCC90.201k3
Company - TransCore
Minimum attenuation 55dB (Line at 75.5dBuV)
140.0

130.0

120.0

110.0
Amplitude dBuV

100.0

90.0

80.0

70.0

60.0

50.0

40.0
100.0M 1.0G 10.0G
Frequency

Operator: Norman Shpilsher

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 29 of 63

A
3.4 Out of Band Spurious Emissions at Antenna Terminal, FCC 90.210(k)(3)(ii), 2.1051

Out-of-band measurements were made for frequencies:
- 902MHz
- 904MHz
- 909.5MHz
- 921.75MHz.

Output frequencies of the EUT was set to:
- 902.25MHz (CW)
- 903.75MHz (CW)
- 910.00MHz (CW)
- 921.50MHz (CW)
- 912.75MHz (Modulated RF)
- 918.75MHz (Modulated RF)

Test Procedure

The Spurious Emissions at Antenna Terminal for the device was measured at the maximum power
transmission condition. The transmitter antenna port was connected to the Spectrum analyzer via the
attenuator.

Total Emissions level was calculated from Measured Power adding 6.2dB of the external-of-analyzer
attenuator.

The Minimum Emission Attenuation calculation
The minimum emissions attenuation was calculated using the maximum output power P (Watt):
Minimum Attenuation = 55 + 10log (P)
The maximum measured output power in Section 3.1 is 29.5dBm, or 0.891 Watt
According to the client specification, the maximum output power at antenna terminal is 1 Watt, or 30dBm.
As a worse case, the Minimum Attenuation based on 1Watt maximum output power is chosen as a
reference level:
Minimum Attenuation = 55 + 10log (P) = 55 + 10log(1Watt) = 55dB

Measurements were taken using 100kHz Resolution Bandwidth (RBW) of the Analyzer, for frequencies
within 1MHz of the Bandedge 300Hz RBW was used.

Table and graphs below show the out-of-band spurious emissions at antenna terminal
Note: Emission level shown in the Graphs does not include 6.2dB attenuation factor of the attenuator.

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 30 of 63

A
Out-of-band Spurious Emissions at Antenna Terminal Date: 01-14-2001
Company: TransCore
Model: IT2611
Test Engineer: Norman Shpilsher
Special Config. Info: The EUT antenna terminal was connected to the Spectrum
Analyzer through the attenuator 6.2dB (including cable loss).
Standard: FCC Part 90.210(k)(3)(ii) and Part 2.1051
Note: Measurements were taken using 100kHz Resolution Bandwidth (RBW) of the Analyzer,
for frequencies within 1MHz of the Bandedge 300Hz RBW was used (indicated in the Table).

Table # 3-4-1

Output Edge Maximum Minimum Measured
Freq. Freq. Output Power Atten. Atten. Margin Comments
MHz MHz Watt dB dB
902.25 (CW) 902.00 1.0 55.0 80.5 -25.5 RBW 300Hz
903.75 (CW) 904.00 1.0 55.0 79.8 -24.8 RBW 300Hz
910.00 (CW) 909.50 1.0 55.0 82.4 -27.4 RBW 300Hz
921.50 (CW) 921.75 1.0 55.0 80.4 -25.4 RBW 300Hz
912.75 (Mod) 909.50 1.0 55.0 63.0 -8.0
918.75 (Mod) 921.75 1.0 55.0 59.3 -4.3

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 31 of 63

A
3.5 Field Strength of Spurious Emissions, FCC 90.210(k)(3)(ii), 2.1053

Field Strength of Spurious Emissions was measured in the Anechoic Chamber in the frequency range up to
10 GHz (10th harmonic).
The substitution method of measurement was used for emissions with the level of field strength above the
general limits for unintentional radiation for unlicensed devices (FCC 15.109, Class A).
The substitution method of measurement is based on the calculation of the minimum attenuation of the
output ERP of the EUT.

Calculation of the minimum attenuation for antenna AA3152 Universal Toll Antenna
Output ERP = Pmax-at –antenna-terminal + Gantenna-gain
The measured in Section 3.1 maximum emission at antenna terminal Pmax-at –antenna-terminal is
29.5dBm, as a worse case 30dBm (according to the manufacturer specification) is chosen.
Output ERP = Pmax-at –antenna-terminal + Gantenna-gain = 30dBm + 13dBi = 43dbm = 20W
Minimum Attenuation = 55 + 10log (P) = 55 + 10log(20Watt) = 68dB
Maximum Spurious Emissions = Output ERP – Minimum Attenuation = 43dBm –68dB = -25dBm

Calculation of the minimum attenuation for antenna AA3153 Toll Antenna
Output ERP = Pmax-at –antenna-terminal + Gantenna-gain
The measured in Section 3.1 maximum emission at antenna terminal Pmax-at –antenna-terminal is
29.5dBm, as a worse case 30dBm (according to the manufacturer specification) is chosen.
Output ERP = Pmax-at –antenna-terminal + Gantenna-gain = 30dBm + 10.5dBi = 40.5dbm
Output ERP = 11.22W
Minimum Attenuation = 55 + 10log (P) = 55 + 10log(11.22Watt) = 65.5dB
Maximum Spurious Emissions = Output ERP – Minimum Attenuation = 40.5dBm – 65.5dB
Maximum Spurious Emissions = -25dBm

Test Procedure
The EUT was placed on a non-conductive table 0.8m above the ground plane inside the Anecoic Chamber.
The table was centered on a motorized turntable, which allows 360-degree rotation. The measurement
antenna was positioned at distance 3m. The radiated emissions were maximized by configuring the EUT, by
rotating the EUT, by changing antenna polarization, and by changing antenna height from 1 to 4m. Field
strength was measured and calculated (See Section 3.7). The Emissions with the level of about 20dB below
the Maximum Spurious Emissions were chosen for substitution method of measurement.
For substitution method the substitution antenna with the signal generator was placed instead of the EUT
with the center of substitution antenna was at the same location as the center of transmitter. The substitution
antenna was faced to measurement antenna with the same polarization as the measuring antenna. The level
of the generator output was adjusted until the previously recorded maximum emission reading for this set of
conditions is obtained. Substitution method of the Field Strength Calculation sees in Section 3.7.

The Table and Graphs below show the Field Strength of Spurious Radiation.

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 38 of 63

A
Radiated Emissions Date: 01-04-2001
Company: TransCore
Model: IT2611
Test Engineer: Norman Shpilsher
Special Config. Info: Sabstitution Metod
Limits FCC 90.210(k)(3)(ii)
Test Site: 3m Anechoic Chamber
Note: The table shows the worst case radiated emissions

Table # 3-5-1

Frequency Measured Substitution Substitution Substitution Limit Margin
Emissions Antenna Power Antenna Gain Antenna EPR
MHz dB m V dBm dBi Power (dBm) dBm dB

1807.5 62.12 -47.5 8.4 -39.1 -25.0 -14.1
1829.8 48.44 -55.9 8.4 -47.5 -25.0 -22.5
2708.2 61.19 -39.5 9.4 -30.1 -25.0 -5.1
2745.4 57.09 -43.6 9.4 -34.2 -25.0 -9.2

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 39 of 63

A
Graph # 3-5-1

Job # - 3011655
Company - TransCore
INTERTEK TESTING SERVICES maximum_v_h_cf
Maximum_12
RADIATED EMISSIONS 30MHz - 1GHz fcca
Model # - IT2611
Serial # -
80.0

75.0

70.0

65.0

60.0
Amplitude dBuV

55.0

50.0

45.0

40.0

35.0

30.0

25.0

20.0

15.0

10.0
10.00M 100.00M 1.00G
Frequency MHz

Operator: Norman Shpilsher Job #: 3011655

Graph # 3-5-2

Job # - 3011655
Company - TransCore INTERTEK TESTING SERVICES maximum_v_h_cf
Model # - IT2611 Radiated Emissions 1GHz-10GHz Maximum_12
Serial # - fcc _a
Additional Equipment -
70.0

65.0

60.0

55.0

50.0
Amplitude dBuV

45.0

40.0

35.0

30.0

25.0

20.0

15.0

10.0

5.0

0
1.0G 10.0G
Frequency GHz

Operator: Norman Shpilsher Job #: 3011655

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 40 of 63

A
3.6 Frequency Stability, FCC 90.213(a), 2.1055

Frequency Stability with variation of ambient temperature was measured from –30 degrees C to +50
degrees C at frequency 915.75MHz and rated power input 120VAC/60Hz.

Frequency Stability with variation of primary supply voltage was measured at 85% (102V) and 115%
(138V) of rated AC Power Supply input voltage of 120V at frequency 915.75MHz.

Note: FCC 90.213(a) indicates that fixed non-multilateration transmitters with an authorized bandwidth that
is more than 40kHz from the band edge is not subject to frequency tolerance restriction.

Table and below shows the frequency stability vs. temperature ambient and supply voltage.

Test Procedure

The EUT was placed in an environmental test chamber and powered such that control element received
normal voltage and the transmitter provided maximum RF output. The Chamber was programmed to cool
from room temperature to minus 30 degrees C and then step in 10-degree increments to plus 50 degrees C.
For Frequency Stability testing with variation of primary supply voltage the EUT power supply was
powered at rated supply voltage at 120VAC/60Hz and then at 102VAC/60Hz and 138VAC/60Hz

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 41 of 63

A
Frequency Stability Date: 01-11-2002
Company: TransCore
Model: IT2611
Special Config. Info: Enviromental Chamber (Frequency Stability testing)
Test Engineer: Norman Shpilsher
Standard: FCC 90.213(a), FCC 2.1055

Table # 3-6-1

Output Frequency Frequency Minimum Freq. Test
Temperature Frequency Stability Stability Stability Result
Degree C MHz Hz ppm ppm
-30 915.75 445 0.5 2.5 Pass
-20 915.75 354 0.4 2.5 Pass
-10 915.75 234 0.3 2.5 Pass
0 915.75 94 0.1 2.5 Pass
10 915.75 22 0.0 2.5 Pass
20 915.75 0 0.0 2.5 Pass
30 915.75 84 0.1 2.5 Pass
40 915.75 178 0.2 2.5 Pass
50 915.75 218 0.2 2.5 Pass
Input Power Output Frequency Frequency Minimum Freq. Test
AC Voltage Frequency Stability Stability Stability Result
V MHz Hz ppm ppm

102 915.75 10.0 0.0 2.5 Pass
120 915.75 0.0 0.0 2.5 Pass
138 915.75 10.0 0.0 2.5 Pass

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 42 of 63

A

EXHIBIT I

TEST SET UP PHOTOS

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 45 of 63

A

EXHIBIT II

FCC ID LABEL LOCATION

(See ID Label/Location Info. Attachments)

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 50 of 63

A

EXHIBIT III

EXTERNAL PHOTOS

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 51 of 63

A

EXHIBIT IV

INTERNAL PHOTOS

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 54 of 63

A

EXHIBIT V

ELECTRICAL SCHEMATICS AND BLOCK DIAGRAM

(See Block Diagram and Schematic Attachments)

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 62 of 63

A

EXHIBIT VI

USER MANUAL AND OPERATIONAL DESCRIPTION

(See User Manual and Operational Description Attachments)

FCC ID: FIH2611SS Report No:3011655 Rev. 3 – March, 2002 Page 63 of 63

Document Created: 2019-02-16 10:54:44
Document Modified: 2019-02-16 10:54:44

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC