Directional Antenna Information

0864-EX-PL-2014 Text Documents

General Dynamics C4 Systems

2014-12-05ELS_156628

800 10734V01 700 MHz Single Band 4', 65 Degree Antenna RET Kathrein’s X-polarized antennas are designed for use in digital polarization diversity systems. • X-polarized (+45° and -45°). • UV resistant fiberglass radomes. • Wideband vector dipole technology. 0° 33 ° 3 30 • DC Grounded metallic parts for impulse suppression. 0° 10 30 ° 0° 60 • RET motor housed inside the radome and field replaceable. 20 30 270° 90° General specifications: 12 0° 0° 24 Frequency range 698–894 MHz VSWR <1.5:1 15 0° 21 0° 180° Impedance 50 ohms Horizontal pattern Intermodulation (2x20w) IM3: <-150 dBc ±45°- polarization Polarization +45° and -45° 0° Maximum input power 500 watts per input (at 50°C) 33 ° 3 30 0° 10 Connector 2 x 7-16 DIN female (long neck) 30 0° 20 60 ° (bottom mounted) 30 Isolation >30 dB 270° 90° Electrical downtilt 0–16 degrees (continuously adjustable) See reverse for order information. 24 0° 12 0° 15 0° 21 0° 180° Specifications: 698–806 MHz 824–894 MHz Vertical pattern ±45°- polarization Gain 14.2 dBi 14.8 dBi 0°–16° electrical downtilt Front-to-back ratio >30 dB (co-polar) >30 dB (co-polar) 32 dB (average) 33 dB (average) +45° and -45° polarization 68° (half-power) 65° (half-power) horizontal beamwidth +45° and -45° polarization 16° (half-power) 14.8° (half-power) vertical beamwidth Min. sidelobe suppression for 0° 8° 16° T 0° 8° 16° T first sidelobe above main beam 16 17 17 dB 18 17 16 dB average 16 19 20 dB 20 20 20 dB Cross polar ratio Main direction 0° 24 dB (typical) 23 dB (typical) Sector ±60° >10 dB, Average: 15 dB >10 dB, Average: 16 dB 1) The protocol of the logical interface can be switched IRT specifications: from 3GPP/AISG 2.0 to AISG 1.1 and vice versa with a vendor specific command. Start-up operation of the RCU Logical interface ex factory1 3GPP/AISG 2.0 86010149 is possible in an RET system supporting AISG Protocols AISG 1.1 and 3GPP/AISG 2.0 compliant 1.1 or supporting 3GPP/AISG 2.0 after performing a layer 2 reset before address assignment. The protocol can also be Hardware interface2 2 x 8 pin connector acc. IEC 60130-9; changed as follows: AISG 1.1 to 3GPP: Enter "3GPP" into according to AISG: the additional data filed "Installer’s ID" and perform a layer – IRT in (male): Control / Daisy chain in 7 reset or a power reset. 3GPP to AISG 1.1: Enter "AISG – IRT in (female): Daisy chain out 1" into the additional datafield "Installer’s ID" and perform a layer 2 reset or a power reset. After switching the protocol any Power supply 10–30 V other information can be entered into the "Installer’s ID" field. Power consumption <1 watt (standby) 2) The tightning torque for fixing the connector must be 0.5 – 1.0 <8.5 watts (motor activated) Nm (‘hand-tightened’). The connector should be tightened by hand only! Adjustment time (full range) 40 sec. Adjustment cycles >50,000 Certification FCC 15.107 Class B Computing Devices 11385-A Oct 6, 2011 936.4272 Kathrein Inc., Scala Division Post Office Box 4580 Medford, OR 97501 (USA) Phone: (541) 779-6500 Fax: (541) 779-3991 Email: communications@kathrein.com Internet: www.kathrein-scala.com

800 10734V01 700 MHz Single Band 4', 65 Degree Antenna RET Mechanical specifications: Weight 24.3 lb (11 kg) 28.7 lb (13 kg) clamps included Dimensions H x W x D 53.3 x 11.9 x 3.9 inches (1355 x 303 x 99 mm) Wind load at 93 mph (150kph) Front/Side/Rear 140 lbf / 45 lbf / 160 lbf (620 N) / (200 N) / (710 N) Mounting category M (Medium) Wind survival rating* 150 mph (240 kph) Shipping dimensions 56.3 x 12.4 x 4.5 inches (1430 x 315 x 115 mm) 64 mm Shipping weight 33.1 lb (15 kg) M8 Mounting bracket 2-point hot-dip galvanized with stainless steel hardware for 2 to 4.5 inch (50 to 115 mm) OD masts. 2.625 inches ± 0.125 (68 mm ± 4) Mounting Brackets for use with 2-point mount antennas Mast dia. 2–4.5 inches (50–115 mm) Weight: 4.4 lb (2 kg) 56.9 inches (1446 mm) 55.4 inches (1406 mm) KATHREIN 860 10149 53.3 inches Tested To Comply (1355 mm) With FCC Standards This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: Refer to part number 860 10149 for the 3.9 inches specifications of the (99 mm) remote control actuator. Mechanical Tilt Brackets 11.9 inches for use with 2-point mount antennas (303 mm) Weight: 7.4 lb (3.7 kg) (Model 850 10013) IRT 698–894 698–894 in out +45° –45° 8pin 8pin 7-16 7-16 male female Order Information: * Mechanical design is based on environmental conditions as stipulated in TIA-222-G-2 (December 2009) and/or Model Description ETS 300 019-1-4 which include the static mechanical 800 10734V01 Antenna with mounting bracket load imposed on an antenna by wind at maximum 0°–16° electrical downtilt velocity. See the Engineering Section of the catalog for further details. 800 10734V01K Antenna with Antenna with mounting bracket and mechanical tilt bracket 0°–16° electrical downtilt All specifications are subject to change without notice. The latest specifications are available at www.kathrein-scala.com. Kathrein Inc., Scala Division Post Office Box 4580 Medford, OR 97501 (USA) Phone: (541) 779-6500 Fax: (541) 779-3991 Email: communications@kathrein.com Internet: www.kathrein-scala.com


Document Created: 2012-08-22 09:39:25
Document Modified: 2012-08-22 09:39:25
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC