Supplemental Information

0533-EX-ST-2015 Text Documents

Garmin International

2015-05-15ELS_162443

Exhibit 2: Supplemental Information Table of Contents 1. Purpose ............................................................................................................................................... 1 2. Applicable HIRF Directives .................................................................................................................. 1 2.1. Applicable Code of Federal Regulations (CFR) .......................................................................... 1 2.2. FAA Guidance ............................................................................................................................. 1 2.3. Industry Guidance........................................................................................................................ 1 3. Equipment Information ........................................................................................................................ 2 4. Transmitted Signal Information............................................................................................................ 3 5. “Stop Buzzer” Contacts ....................................................................................................................... 3 1. Purpose This exhibit provides supplemental Information in support of the application for Special Temporary Authorization (STA). 2. Applicable HIRF Directives This Special Temporary Authorization (STA) is required to conduct testing necessary to support aircraft certification for High Intensity Radiated Fields (HIRF). The test data will be used to assure compliance with HIRF requirements as specified by the following directives. 2.1. Applicable Code of Federal Regulations (CFR) 14 CFR 23.1308 High-intensity Radiated Fields (HIRF) Protection 14 CFR 25.1317 High-intensity Radiated Fields (HIRF) Protection 14 CFR 27.1317 High-intensity Radiated Fields (HIRF) Protection 14 CFR 29.1317 High-intensity Radiated Fields (HIRF) Protection 2.2. FAA Guidance AC20-158 The Certification of Electrical and Electronic Systems for Operation in the High Intensity Radiated Fields (HIRF) Environment. FAA 8110.71 Guidance for the Certification of Aircraft Operating in High Intensity Radiated Field (HIRF) Environments 2.3. Industry Guidance RTCA DO-160E/F/G Environmental Conditions and Test Procedures for Airborne Equipment ED90A Radio Frequency Susceptibility Test Procedure ED107 Guide to Certification of Aircraft in a High Intensity Field (HIRF) Environment SAE ARP5583A Guide to Certification of Aircraft in a High Intensity Radiated Field (HIRF) Environment. Exhibit 2: Supplemental Information Page 1 of 3

3. Equipment Information All primary field generation and monitoring equipment is listed in Table 1 below. Table 1: Equipment List Item Manufacturer Model (See note) Signal Generator Agilent E8257D Spectrum Analyzer Agilent N9010A HF Amplifier ENI 5100L Microwave Amplifier Miteq 100M-20G 30dB 20dBm Amplifier Coax Cables Miscellaneous Various DC-18GHz Low Loss Coax Fiber Optic Receiver System PPM Fiber optic processing system Fiber Optic Cable Miscellaneous Fiber optic cables Directional Coupler Amplifier Research DC2500 Current Probe Eaton 94111-1 Tx Dipole Antenna Custom 10MHz Dipole Antenna Tx Bi-Log Antenna 30MHz-1GHz ETS Lindgren 3142C Tx Horn Antenna 400MHz-1GHz AR ATH400M1G Tx Horn Antenna 1GHz-18GHz ETS Lindgren 3115 D-dot Sensor EG & G ACD-10A Broadband Rx Antenna Custom 100M-18GHz Rx Antenna Note: Equivalent equipment may be substituted as necessary Table 2: Tx Antenna VSWR and 3dB Beamwidth Antenna Model VSWR 3dB Beamwidth ETS 3142 Bi-Log 2:1 Average above 80MHz Varying from approximately 60º at 400MHz to AR ATH400M1G Max 2.5:1, Average 1.5:1 35º at 1Ghz. ETS 3115 Horn Exhibit 2: Supplemental Information Page 2 of 3

4. Transmitted Signal Information Frequency Various documents referenced in Section 2 of this exhibit provide guidance as to how to perform Low Level Coupling (LLC) testing. This guidance specifies the use of a signal generator and receiver system setup in a tracking generator configuration such that the test frequency is swept continuously across a specified frequency band. Testing using swept frequencies rather than widely spaced discrete frequencies allows for a more accurate measurement of aircraft and wiring resonant responses. This method also simplifies the test setup and minimizes frequency dwell time. The effective dwell time at each swept frequency is much less than 1s. We request permission to perform swept frequency testing across all approved test frequency bands listed in the application. Frequencies reserved for emergency services or local aircraft control will be omitted from the test. Modulation All testing is performed using a Continuous Wave (CW) signal (i.e. no modulation). Therefore, no actual data is being transmitted during the test. Power Transmitted power must be high enough to allow accurate monitoring using a sensitive receiver system. All transmitted power levels will remain less than the specified band specific Effective Radiated Power (ERP) as specified in the application. The power levels requested are for maximum Effective Isotropic Radiated Power (EIRP) at the transmit antenna. Coordination with the local FCC and FAA can be accomplished as necessary. 5. “Stop Buzzer” Contacts The following contacts can be contacted at any time to stop the test in case of a conflict. Steve Haycock, Engineer Desk: 913-440-2284 Aaron Jones, Engineer Desk: 913-440-5065 David Kerr, Engineer Desk: 913-440-5208 Praf Patel, Engineer Desk: 913-440-5422 Nick Filla, Engineer Desk: 913-440-2650 Brad Fischer, Flight Operations Desk: 913-440-8421 Exhibit 2: Supplemental Information Page 3 of 3


Document Created: 2015-05-15 13:14:06
Document Modified: 2015-05-15 13:14:06
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC