Orbital Debris Assessment Report

0353-EX-CN-2017 Text Documents

Boston University

2017-05-08ELS_191677

ELVL-2017-0044671 March 9, 2017 Orbital Debris Assessment for The CubeSats on the ELaNa-XIX Mission per NASA-STD 8719.14A (FCC)

Signature Page 2

National Aeronautics and Space Administration John F. Kennedy Space Center, Florida Kennedy Space Center, FL 32899 ELVL-2017-0044671 Reply to Attn of: VA-H1 March 9, 2017 TO: Justin Treptow, LSP Mission Manager, NASA/KSC/VA-G2 FROM: Justin Treptow, NASA/KSC/VA-G2 SUBJECT: Orbital Debris Assessment Report (ODAR) for the ELaNa-XIX Mission (FCC) REFERENCES: A. NASA Procedural Requirements for Limiting Orbital Debris Generation, NPR 8715.6A, 5 February 2008 B. Process for Limiting Orbital Debris, NASA-STD-8719.14A, 25 May 2012 C. Armstrong, Jason; TriSept Corp. “ODAR info” email, Oct 20, 2016. D. McKissock, Barbara, Patricia Loyselle, and Elisa Vogel. Guidelines on Lithium- ion Battery Use in Space Applications. Tech. no. RP-08-75. NASA Glenn Research Center Cleveland, Ohio E. UL Standard for Safety for Lithium Batteries, UL 1642. UL Standard. 4th ed. Northbrook, IL, Underwriters Laboratories, 2007 F. Kwas, Robert. Thermal Analysis of ELaNa-4 CubeSat Batteries, ELVL-2012- 0043254; Nov 2012 G. Range Safety User Requirements Manual Volume 3- Launch Vehicles, Payloads, and Ground Support Systems Requirements, AFSCM 91-710 V3. H. HQ OSMA Policy Memo/Email to 8719.14: CubeSat Battery Non-Passivation, Suzanne Aleman to Justin Treptow, 10, March 2014 I. Electron LV-Payload Interface Control Document, ELVL-2016-0044579, Received October 24, 2016 The intent of this report is to satisfy the orbital debris requirements listed in ref. (a) for the ELaNa-19 primary mission payload. It serves as the final submittal in support of the spacecraft Safety and Mission Success Review (SMSR). Sections 1 through 8 of ref. (b) are addressed in this document; sections 9 through 14 fall under the requirements levied on the primary mission and are not presented here. 3

The following table summarizes the compliance status of the ELaNa XIX (ELana-19) auxiliary payload mission flown on ELaNa-19. The fourteen CubeSats comprising the ELaNa-19 mission are fully compliant with all applicable requirements. Table 1: Orbital Debris Requirement Compliance Matrix Requirement Compliance Assessment Comments 4.3-1a Not applicable No planned debris release 4.3-1b Not applicable No planned debris release 4.3-2 Not applicable No planned debris release 4.4-1 Compliant On board energy source (batteries) incapable of debris-producing failure 4.4-2 Compliant On board energy source (batteries) incapable of debris-producing failure 4.4-3 Not applicable No planned breakups 4.4-4 Not applicable No planned breakups 4.5-1 Compliant 4.5-2 Not applicable 4.6-1(a) Compliant Worst case lifetime 6.2 yrs 4.6-1(b) Not applicable 4.6-1(c) Not applicable 4.6-2 Not applicable 4.6-3 Not applicable 4.6-4 Not applicable Passive disposal 4.6-5 Compliant 4.7-1 Compliant Non-credible risk of human casualty 4.8-1 Compliant ELaNa-19 includes the CubeSail mission, containing a 250m solar sail / tether 4

Section 1: Program Management and Mission Overview The ELaNa-19 mission is sponsored by the Human Exploration and Operations Mission Directorate at NASA Headquarters. The Program Executive is Jason Crusan. Responsible senior scientific / management personnel are as follows: ANDESITE: Walsh Brian, Principle Investigator CeREs: Summerlin Errol, Principle Investigator CHOMPTT: Conklin John, Principle Investigator CubeSail: Carroll David, Principle Investigator DaVinci: Finman Lorna, Principle Investigator ISX: Bellardo John, Principle Investigator NMTSat: Jorgensen Anders, Principle Investigator RSat: Kang Jin, Principle Investigator Shields-1: Thomsen Laurence, Principle Investigator STF-1: Grubb Matthew, Principle Investigator TOMSat EAGLESCOUT: Hattersley Bonnie, Principle Investigator TOMSat R3: Hattersley Bonnie, Principle Investigator GEOStare: de Vries Wim, Principle Investigator SHFT-1: Lux Jim, Principle Investigator 5

Program Milestone Schedule Task Date CubeSat Selection CSLI award February 2016 CubeSat Mission Readiness review: February 28th 2017 CubeSat delivery to TriSept October 2017 CubeSat integration with LV October 2017 Launch date NET November 2017 Figure 1: Program Milestone Schedule The ELaNa-19 mission will be launched as the primary payload on the VCLS RocketLabs ELaNa-19 mission on an US made Electron launch vehicle from New Zealand range. The ELaNa-19 compliment, will deploy 14 pico-satellites (or CubeSats). The CubeSat slotted position is identified in Table 2: ELaNa-19 CubeSats. The ELaNa- 19 manifest includes: ANDESITE, CeREs, CHOMPTT , CubeSail, DaVinci, ISX, NMTSat, RSat, Shields-1, STF-1, TOMSat EAGLESCOUT, TOMSat R3, GEOStare, and SHFT-1. The current launch date is no earlier than (NET) November, 2017. The 14 CubeSats are to be ejected from the Electron shortly after the launch, placing the CubeSats in an orbit approximately 500 X 500 km at inclination of 85 deg (ref. (i)). Each CubeSat ranges in sizes from a 10 cm x 10cm x 30 cm to 10 cm x 20 cm x 30 cm, with masses from about 1.56 kg to ~5.13 kg total. The CubeSats have been designed and universities and government agencies and each has their own mission goals. 6

Section 2: Spacecraft Description There are 14 CubeSats flying on the ELaNa-19 Mission. Table 2: ELaNa-19 CubeSats outlines their generic attributes. Table 2: ELaNa-19 CubeSats CubeSat CubeSat CubeSat Masses CubeSat size Quantity Names (kg) 1 6U (24 cm x 36.3 cm x 11 cm) ANDESITE 5.13 1 3U (10 cm x 10 cm x 34 cm) CeREs 4.56 1 3U (10 cm x 10 cm x 34 cm) CHOMPTT 1.56 1 3U (10 cm x 10 cm x 31 cm) CubeSail 3.52 1 3U (11.7 cm x 11.3 cm x 34.05 cm) DaVinci 3.36 1 3U (11.2 cm x 11.1 cm x 34.05 cm) ISX 3.70 1 3U (10 cm x 10 cm x 34 cm) NMTSat 1.58 1 3U (11.3 cm x 11.3 cm x 34.05 cm) Rsat 4.15 1 3U (10.6 cm x 10.6 cm x 34.05 cm) Shields-1 6.94 1 3U (11.5 cm x 11.5 cm x 34.05 cm) STF-1 3.35 TOMSat 1 3U (10.3 cm x 10.3 cm x 34.05 cm) 4.09 EAGLESCOUT 1 3U (10.3 cm x 10.3 cm x 34.05 cm) TOMSat R3 4.09 1 3U (11.2 cm x 11.1 cm x 34.05 cm) GEOStare 3.99 1 3U (11.3 cm x 11.2 cm x 36.6 cm) SHFT-1 5.10 The following subsections contain descriptions of these 14 CubeSats. 7

ANDESITE - Boston University – 6U Figure 2: ANDESITE System and Expanded View Figure 3: ANDESITE Sensor Node Deployment & Node Expanded View Figure 4: Sensor Node Expanded View OVERVIEW The design of ANDESITE relies on deploying several small “sensor nodes'' from a main spacecraft—a 6U “mule” designed to comply with CubeSat Canisterized Satellite Dispenser (CSD) standards. Each sensor node holds a magnetometer that will provide three-axis magnetic field measurements with roughly ten nanotesla accuracy. By distributing the sensor nodes spatially, the system measures relative variations of the field as it flies through the aurora. With Ampere's law from Maxwell's equations and a priori knowledge of Earth’s background magnetic field we can calculate and map the current densities due to energetic charged particles moving into and out of the atmosphere in the polar regions where the aurora occurs. 8

CONOPS The ANDESITE system consists of 8 identical sensor nodes, and a 6U “data mule.” All 9 satellites deploy in a single configuration called the aggregate satellite into a 500 km altitude near circular orbit at 85 degrees inclination. At this time, the aggregate satellite will enter de-tumbling mode. During this phase, the attitude control system on the 6U— designed around a three-axis magnetorquer from ISISpace—will activate and stabilize the craft using state knowledge garnered from six onboard sun sensors, gyros, and magnetometer. While nodes will be launched with pre-charged batteries, a slow rotation rate stabilized towards sun vector will ensure that the mule batteries are at full capacity before entering the next phase of the deployment. Once de-tumbling is finished the mule will stabilize with the bottom plate nadir pointing and eject a pair of sensor nodes once per orbit cross- track near the equator. The sensor nodes begin startup sequences the moment they are launched from the mule via a mechanical switch. After initialization device discovery occurs and the self- organizing sensor network is consolidated so that magnetometer data can be relayed back to the mule during the science mission. Materials The primary CubeSat structure is made of aluminum 6061. The baseplate is made of aluminum 7075 and is hard anodized. The CubeSat contains all standard commercial off the shelf (COTS) materials, electrical components, PCBs and solar cells. It has eight deployable picosatellites that eject while in orbit, and two deployable solar panel wings that deploy upon exit of the Canesterized Satellite Dispenser (CSD). The picosatellites have an aluminum 6061 structure and PCBs for solar cells and on board electronics. Stainless steel 6-32 and 2-56 screws are used to fasten the CubeSat, and helicoils are inserted for back-out protection. Hazards There no pressure vessels, hazardous or exotic materials. Batteries The electrical power storage system consists of common Lithium-Ion Polymer batteries with over-charge/current protection circuitry provided by a Clyde Space EPS. Clyde Space battery part number C3-USM-5016-CS-30Wh. 9

CeREs -GSFC – 3U Figure 5: CeREs CubeSat Expanded View OVERVIEW CeREs is a 3U CubeSat carrying a single instrument to study radiation belt dynamics in support of the Van Allen Probes. Specifically, the detector, MeRIT, a combination of solid state detectors (SSDs) and avalanche photo diodes (APDs) will measure electrons with energies between 10keV and 10 MeV with extremely fast (5ms) cadence. This unprecedented measurement range comes from seamlessly combing SSD technology, sensitive to higher energy electrons with new APDs which are sensitive to lower energy electrons. The high measurement cadence is supported advanced application specific integrated circuits that can handle millions of events per second. Electrons at these energies precipitating over the poles can have sudden bursts of intensity that last only a few microseconds called microbursts. These were first seen by the SAMPEX mission with a 20 ms cadence for electrons greater than 1 MeV, but because of the limited instrument capability, it is still unknown exactly how short these bursts can be and what the distribution of electron energies is within these events. Microbursts have intensities an order of magnitude larger than typical rates of precipitating electrons and one of the goals of the Van Allen Probes was to investigate the origins of these events. CeREs will help Van Allen Probes achieve this objective by 10

providing direct measurements of precipitating electrons that can be correlated with events observed on Van Allen Probes at lower latitudes along the same magnetic field line. CONOPS Upon Release, CeREs will power-up, deploy its solar arrays, and enter sun acquisition mode. It will then deploy its antenna and use its GPS to decide when to “beacon” to help with initial ground contact. Once initial ground contact is established, CeREs will begin science operations. These will consist of pointing the instrument toward zenith above ~60 degrees latitude and entering a power saving/sun acquisition mode at low latitudes on the night/day side respectively. Twice per day, power permitting, the sun acquisition mode will be interrupted for a 15 minutes ground contact with WFF. As the mission continues, power levels will be monitored to ensure that sufficient time is being allocated for power acquisition daily and the 60 degree latitude value will change as solar panel efficiencies and battery power degrades. The mission will generate and transmit up to 2.7 Gb of data daily that will consist of distribution functions of energetic electrons over 3-orders of magnitude in energy. Ground contacts, data acquisition rates, and the latitude at which science operations begin are all controlled via tables uploaded to the spacecraft regularly and can be changed in response to spacecraft status. Materials The primary CubeSat structure is made of Aluminum 6061-T6. The detectors are made of silicon and the shielding for the detectors is made of tungsten and aluminum. Instrument front end electronics and on-board processor cards are copper and FR4. The front end electronics also have a high voltage power supply that is housed in Urethane. The XB1 avionics package, includes lithium-ion batteries, C&DH processor, L3 Cadet Radio, and the ACS system. These are housed in an aluminum shell. The solar panels contain primarily FR4 and Aluminum with steel hinges. Hazards There are no pressure vessels, hazardous or exotic materials. Batteries The electrical power storage system consists of common Lithium-Ion batteries with under temperature (hardware set), cell balancing, under voltage and over voltage protection features. Specs on the EPS system can be found here (http://bluecanyontech.com/wp- content/uploads/2016/07/PowerSystems_F.pdf). 11

CHOMPTT-University of Florida – 3U Figure 6: CHOMPTT Expanded View Figure 7: CHOMPTT Zenith (left) and Nadir (right) Views 12

Figure 8: CHOMPTT Stowed View Overview CHOMPTT (CubeSat Handling of Multisystem Precision Time Transfer) is a CubeSat mission that will synchronize an atomic clock on a CubeSat with one on the ground with an accuracy of 200 ps by exchanging short laser pulses between the two. One limitation of radio frequency time-transfer is that it is susceptible to time-delay uncertainties in the ionosphere that can be difficult to model. This effect is inversely proportional to the emitted electromagnetic frequency squared and can therefore be greatly reduced by utilizing optical synchronization methods. The CHOMPTT satellite will maintain its time with a chip scale atomic clock (CSAC). When the satellite passes over a satellite laser ranging facility (SLR), the SLR facility emits a laser pulse toward the satellite. That pulse is time-stamped with respect to the ground clock when it leaves the SLR facility and after it reflects of off a retroreflector on the satellite, the returned pulse is time-stamped when it arrives back at the SLR facility with respect to the ground clock. An avalanche photodetector on the satellite simultaneously detects the pulse’s arrival time and time-stamps it with respect to the clock on the satellite with an event timer. The combination of these three timing measurements provides both the range between the SLR facility and CHOMPTT and the time offset between the ground clock and the space clock. The CHOMPTT mission is owned and operated by the University of Florida. The CHOMPTT satellite consists of a 1.5U EDSN/NODeS-derived CubeSat bus and a 1U OPTI (Optical Precision Timing Instrument) payload. NASA does not claim ownership of any experimental, developmental or operational equipment that involves the use of the electromagnetic spectrum for transmission, reception, or both that is developed or procured under this contract. The University of Florida’s use of any experimental, developmental or operational equipment that involves the use of the electromagnetic spectrum for transmission, reception, or both that is operated under this contract shall be under University of Florida’s discretion and control; NASA does not claim any authority over the operations of the electromagnetic spectrum systems. 13

CONOPS Upon deployment from the deployer, CHOMPTT will enter a safe-mode for 30 min. where all of the subsystems are nominally off. After the safe-mode period checks out, the spacecraft will power on, begin counting, beacon the spacecraft time every 60 s, and begin de-tumbling via magnetorquer for 90 min. Every 25 hour minor cycle, the spacecraft will autonomously acquire GPS data and downlink spacecraft data to the University of Florida RF ground station. UF will coordinate with a satellite laser ranging (SLR) facility located at Kennedy Space Center to perform a time transfer and RF uplink the time transfer schedule to the spacecraft. During a time transfer, the spacecraft will point nadir, turn on the laser beacon diode for SLR tracking, and turn on all of the payload subsystems. The spacecraft will be pulsed with a laser from the SLR facility until the scheduled time transfer is over, and the spacecraft will return to its nominal counting/beacon mode. Materials The primary CubeSat structure is made of Aluminum and contains a 1.5U EDSN/NODeS derived bus and a 1U UF Optical Precision Timing Instrument (OPTI). The EDSN/NODeS derived bus is custom with a few commercial off the shelf (COTS) components. The custom spacecraft materials are all spacecraft PCBs, all payload components, retroreflector array, TASC 1U solar panels, structures, and reaction wheel system. The COTS spacecraft materials are the GOMSpace P110 1U solar panels with magnetorquers, MEMSpace Sun Sensors, Pumpkin large aperture plate on the 1U nadir face, GPS patch antenna, GPS radio, lithium-ion batteries, Lithium-1 Radio, and StenSat Radio. Hazards There are no pressure vessels, hazardous or exotic materials. Batteries The electrical power storage system consists of common Lithium-Ion batteries with over- charge/current protection circuitry. UL Listing information is as follows UL 1642. 14

CubeSail – UIUC/CUA – 3U Middle Plate Radio (2) Solar Panels (8) Torque Coil (10?) Power Board (2) Patch Antennas (2) Solar Sail C&DH Board (2) Batteries Structural Rails (8) Battery Board Figure 9: CubeSail Expanded View Overview The primary goal of the CubeSail mission is to demonstrate orbit raising from solar sail propulsion. A secondary goal is to then spin-up the satellites like a propeller with the sail extending between them. A final goal is to then deorbit the satellites using the same solar sail. CONOPS Following a successful launch and orbit insertion of the satellites, communication will be initiated to verify satellite functionality. Next, a detumbling maneuver utilizing the flexible magnetic torquers will commence. Once the satellites are stable, the solar sail deployment sequence will begin. Upon launch, the satellites are rigidly coupled using the separation release unit (SRU) and flexibly coupled by the spliced solar sail film, which has been intentionally left slack, and is wound on two bobbins, one in each satellite. The first step of the deployment sequence is to command the SRU motor to spin a leadscrew which will unscrew and rigidly decouple the satellites from each other. Because the leadscrew is not connecting the satellites through their center of mass, there is some resultant tipping. As the satellites separate, the slack in the film is reduced. Once the leadscrew has fully cleared its threaded hole, the film is taught and the separation springs are not compressed. The satellites are given time such that the tipping moment is damped. Next, the film bobbin motors are activated to pull the satellites together using the film thus compressing the separation springs. The force required by the bobbin motors to compress the separation springs is sensed by the circuit and converted to a rotational bobbin motor film deployment speed. The bobbin motors are then activated and begin 15

deploying film at the prescribed velocity. Each satellite has a camera to capture images of the film deployment. As the film nears full deployment, the bobbin motors are commanded to slow down incrementally and significantly to mitigate elastic effects caused by abrupt stopping of the motors or snapping back caused by the taught film. Following complete film deployment, orbital parameters will be detected which will indicate satellite control and orbit raising using the solar sail. Other orbital maneuvers including inducing a spin of the two-satellite system like a propeller using the magnetic torquers for satellite positioning may follow. Once all desired mission objectives are met, a de-orbit command will be given. Materials Satellite structure is made from AL60601T6, while the solar panels are Carbon fiber with an aluminum backing. The CubeSail payload is significantly aluminized mylar film. PCBs are made from FR-4 and using automotive grade or worse components. Hazards There are no hazardous systems on board. There are no pressure vessels nor thrusters nor any chemical reactants. Batteries The electrical power storage system consists of common lithium-ion batteries with over- charge/current protection circuitry. The charging system incorporates an MPPT logic. The lithium batteries carry the UL-listing number MH12210. 16

DaVinci - LCF Enterprises – 3U Figure 10: DaVinci Expanded View Overview The DaVinci mission is a 3U CubeSat being developed by North Idaho STEM Charter Academy in partnership with LCF Enterprises. The primary mission goal is STEM outreach, which will be achieved with the platform payloads. The payloads will be a basic imager to take photographs of the Earth, an amateur radio and a duplex radio modem to connect with the GlobalStar communications network. A morse code message will be communicated as the satellite orbits. CONOPS Upon deployment from the ISIS Quad pack, DaVinci will begin it’s separation sequence. All transmissions and deployments are delayed from 45 minutes from the satellite being deployed. During separation sequence the panels shall be deployed, following on from this DaVinci will minimize the platform angular rate before deploying the UHF/VHF antennas. At this point the initial communication with the ground station/globalstar network shall be made. At this point data will be analyzed to ensure a successful separation has occurred before beginning the primary mission mode. In this mode the satellite can take images and provide a link to the globalstar network via the platform Eyestar modem payload. Materials The primary CubeSat structure is made of Aluminum 6082. It contains all standard commercial off the shelf (COTS) materials, electrical components, PCBs and solar cells. Hazards There are no pressure vessels, hazardous or exotic materials. Batteries The electrical power storage system consists of common Lithium Ion Polymer batteries with over-charge/current protection circuitry. UL Listing information is as follows UL1642. 17

ISX (Ionospheric Scintillation eXplorer) – Cal Poly, SLO – 3U Figure 11: ISX Expanded View Overview The Ionospheric Scintillation eXplorer (ISX) is a satellite developed by undergraduate and graduate students as part of the PolySat research group in collaboration with SRI. The satellite is sponsored by NSF. ISX will measure the scintillation of disrupts in ionospheric plasma tubules using DTV signals. ISX will study the multi-frequency radio wave propagation properties of intermediate-to-large scale ionospheric structures of Equatorial Spread F that cause rapid phase and amplitude fluctuation of transionospheric signals. CONOPS Upon deployment from the PPOD, ISX will power on. Approximately 15 minutes later, the antenna will deploy. 115 minutes after antenna deployment, the beacon will be activated and the satellite will be available to acquire with the ground station. Acquisition and verification of the correct orientation and rates of the satellite will take place one week into the mission. The payload will then start taking data for one year. Materials The structure is made of 6061-T6 Aluminum. The antenna is made of NiTi. The antenna route is made of Delrin. It contains standard commercial off the shelf (COTS) materials, electrical components, PCBs, and solar cells. Hazards There are no pressure vessels, hazardous or exotic materials. 18

Batteries The electrical power storage system consists of nine 3.7V 2600mAh Lithium-Ion 18650 batteries, model LR1865SK, with over-charge/current protection circuitry. There are three strings in parallel, with each string consisting of three batteries in series. UL Listing information is as follows BBCV2.MH48285. 19

NMTSat –New Mexico Institue of Mining and Technology – 3U+ Figure 12: NMTsat Transparent View Overview NMTSat is a 3U+ CubeSat developed by students at New Mexico Institute of Mining and Technology. Its mission is primarily educational. NMTSat contains the following instruments or experiments: two magnetometers (MAG), one Langmuir Plasma Probe (LPP), one GPS receiver for ionospheric occultation measurements (GAMMA), one electrical health monitoring experiment (EHM) which is integrated with the power control module (PCM), and one FPGA testbed, integrated with the C&DH, one silicon neural processing experiment (SALLSA). CONOPS After deployment NMTSat will power up. A timer will start waiting a time (TBD) before deploying the antennas. NMTSat will then power up the PCM, including EHM, and the magnetometers and begin to collect housekeeping data from these. NMTSat will then begin to emit a identifying beacon signal for a designated amount of time and listen for commands. Ground commands to power up and down instruments are then expected as well as commands to download collected data. A watchdog timer is implemented in the power supply to power-cycle NMTSat to its initial configuration when the timer expires. Regular operation involves uplink of commands to configure the satellite and instruments, and to downlink collected data. 20

Materials The primary CubeSat structure is made of Aluminum 6061. It contains all standard commercial off the shelf (COTS) materials, electrical components, PCBs and solar cells. Hazards There are no pressure vessels, hazardous or exotic materials. Batteries The electrical power storage system consists of a P31u power-management unit made by GomSpace which uses common Li- batteries with over-charge/current protection circuitry. The design is based on heritage from the satellites AAU Cubesat and AAUSAT II. 21

RSat - United States Naval Academy – 3U Bus Frame Arm 2 Arm 1 Robotics Bay Figure 13: RSat Expanded View Overview RSat is a 3U (10 x 10 x 33 cm) cube satellite with two 60 cm, seven degree of freedom robotic arms fitted with manipulators. It is intended to latch onto a host satellite and maneuver, image, and potentially repair various components. The RSat launched through ELaNa XIX will be a free floating launch, intended to validate these capabilities and provide flight heritage and confidence for future launches. CONOPS Upon deployment from the PPOD, RSat will power up and attempt deploy its antenna. It will then wait until it has detumbled to less than 1𝑜𝑜 /𝑠𝑠 before deploying the robotic arms. After deployment the arms will move through a series of test patterns designed to simulate various on-orbit tasks. These patterns will focus on precision, aiming for the ability to maneuver on another satellite with a minimum accuracy across the full range of motion. Materials The primary CubeSat structure is made of 6061 Aluminum. It contains all standard commercial off the shelf (COTS) materials, electrical components, PCBs and solar cells. The arms are made of a space suitable 3D printed material. Hazards There are no pressure vessels, hazardous or exotic materials. Batteries The electrical power storage system consists of common Lithium Ion batteries with over- charge/current protection circuitry. UL Listing information is as follows: UL1642. 22

Shields-1 NASA Langley Research Center – 3U Figure 14: Shields-1 Expanded View Overview The Shields-1 mission with passive attitude control is a technology demonstration for radiation shielding a CubeSat electronics and a radiation shielding experiment to measure the shielding performance with respect to aluminum. There is also a charge dissipation film resistance measurement. In Figure 1, there is a vault for the flight system electronics and a research payload. The satellite is a standard 3U form factor, approximately 10cm x 10cm x 34 cm and weighs 6.9 Kg. The vault section of the CubeSat takes approximately 1.2U of the 3U, with the rest of the area the research payload, which contains the shielding and charge dissipation film resistance experiments. The satellite has four Lithium-Ion batteries. Solar panels cover all 4 3U faces for battery charging. The satellite has an aluminum/ titanium/ tantalum structure for its vault. The research payload structure is made of aluminum with 2 aluminum/ titanium/ tantalum shielding samples and one aluminum titanium sample. During the 1 year mission, the satellite will take dosimetry data from 8 µdosimeters behind various shielding thicknesses, charge dissipation film resistance measurements, and experimental thermal measurements. The satellite will also be taking light and temperature readings from solar panel sensors. The satellite has a turnstile antenna system by ISIS AntS-A up to 55cm in length for each antenna, deployed after the launch vehicle ejects the satellites into orbit. The turnstile antennas are the only protrusions from the flat faces of the satellites (see Figure 1 above). 23

CONOPS Upon deployment from the PPOD, Shields-1 will power up after a 30 minute software timer delay and deploy the turnstile antenna. It will slowly self-orient its long axis in the direction of magnetic field lines over a period of days and spin using passive magnetic attitude control. The ground station is located at Wallops Island, Virginia. Upon initial ground station communication with Wallops Island, Shields-1, Mission Objective A, the Shields-1 Atomic Number (Z) Grade Radiation Shielding Research Experiments using total ionizing dose measurements with 7 µdosimeters in the Research Payload and 1 µdosimeter in the Vault along with thermal measurements, Figure 1, will be turned on and data will be collected four times per orbit. Mission Objective B, the vault µdosimeter, thermal and system telemetry measurements, including solar panel thermal and photodiode measurements will be combined to analyze the commercial system flight boards’ performance. Mission Objective C, the charge dissipation film resistance and thermal measurements will be taken a minimum of one time daily after the initial communication with the spacecraft. Mission Objectives A, B, and C are planned to last for at least a year. Materials The primary CubeSat research payload structure and antenna housing is made from aluminum, Figure 1. The Z-Grade Vault, figure 1, contains the FCPU and radio board, battery board, EPS, and two research payload boards. The Z-grade Vault is made of aluminum, titanium, and tantalum. There are two Z-grade radiation shielding material samples in the research payload section of the spacecraft, Figure 1. The charge dissipation film experiment, which is housed in the antenna housing structure, figure 1, contains 4 stainless steel electrodes, inside a commercial Ultem plastic housing. The Shields-1 electronics contains all standard commercial off the shelf (COTS) materials, electrical components, PCBs and solar cells. Hazards There are no pressure vessels, hazardous or exotic materials. Batteries The electrical power storage system consists of common Lithium Ion batteries with over- charge/current protection circuitry. UL Listing information is as follows: UL 1642. 24

STF-1 NASA IV&V and West Virginia University – 3U Figure 15: STF-1 Expanded View Overview The NASA IV&V objective of Simulation-to-Flight 1 (STF-1), is to demonstrate the utility of the NASA Operational Simulator for Small Satellites across the CubeSat development cycle, from concept planning to mission operations. The STF-1 mission will demonstrate a highly portable simulation and test platform that allows seamless transition of mission development artifacts to flight products. The experimental objectives of this mission are to advance engineering and physical- science research currently being developed at West Virginia University (WVU). Specifically, the STF-1 mission aims to enhance precise orbit determination with commercial GPS receivers, increase IMU performance in the CubeSat form-factor, test the durability and radiation tolerance of III-V Nitride based LEDs, and measure dynamic properties of the ionospheric plasma system. CONOPS Upon deployment from the PPOD, STF-1 will enter the power-up sequence and hold for 30 minutes before deployment of the UHF and Langmuir probe elements. 45 minutes after deployment from the PPOD the UHF radio will be activated for telemetry to be transmitted to the Wallops Island ground station. After initial checkout with the ground station, and at which point the solar panels have sufficiently charged the batteries, STF-1 will enter the experimental mode. In this mode the spacecraft will make decisions on which experiment to execute, based on its position, power available, and experiment priority. The highest priority experiment at the beginning of the operations will be the LED experiment, in order to provide a baseline measurement of the LED performance to be compared with subsequent measurements. 25

Materials The primary structure is made of Aluminum 6082, with body mounted solar panels assembled from PCBs, Kapton adhesive, and commercial solar cells. Internally are a combination of commercial off the shelf (COTS) materials, electrical components, PCBs, and experimental payloads developed at WVU. Hazards There are no pressure vessels, hazardous or exotic materials. Batteries The electrical power storage system consists of common Lithium Ion Polymer batteries with over-charge/current protection circuitry. 26

TOMSat: EAGLESCOUT / R3 - Aerospace Corporation -3U Figure 16:One of two AC11/TOMSat spacecraft with solar panels deployed. Overview & CONOPS The AeroCube 11/Testbed for Optical Missions Satellite (AC11/TOMSat) program consists of two nearly-identical spacecraft that will demonstrate the technological capability of two imaging sensors. One satellite will host a pushbroom time delay integration (TDI) sensor that will provide normalized difference vegetation index (NVDI) data for comparison to NVDI provided by Landsat’s Operational Land Imager (OLI). The second AC11/TOMSat spacecraft will host an SB-501 focal plane array that will image terrestrial, lunar, and stellar targets. Both satellites will have a laser communication downlink. The goal of AC11/TOMSat is to show that these sensors perform comparably to flagship missions, such as Landsat. Materials The AC11/TOMSat spacecraft are 3U CubeSats with outer dimensions of 34 cm x 11 cm x 11 cm. Deployable solar panels extend off the long axis of the spacecraft with dimensions 34 cm x 10 cm. The exterior bus is made from 6061-T6 aluminum and houses all payload and electronics components. The nadir face contains an earth sensor and a sun sensor for attitude determination, a fish-eye camera, laser collimator and uplink receiver, and a radio patch antenna. The zenith face also contains a radio patch antenna as well as two star trackers. The payload for each spacecraft is a custom-made telescope made from aluminum, glass lenses, and titanium spacers and uses about 1.5U of space. A radiator is built into the bus to help the payload maintain proper temperatures. About 1U is dedicated to the avionics block, which houses mission electronics, reaction wheels, batteries, and data storage. These components share flight heritage with previous AeroCube launches. A significant portion of AC11/TOMSat’s flight hardware is derived from earlier AeroCube spacecraft already in orbit. 27

Hazards There are no pressure vessels, hazardous or exotic materials. Batteries Power for the AC11/TOMSat spacecraft is generated by solar cells mounted onto panels that will be deployed from both sides of the bus, as well as cells affixed to the spacecraft bus. These cells are capable of producing up to 23 W of power. Power is stored on-board with lithium-ion batteries. The satellite has 4 batteries mounted in an aluminum 6061-T6 structure as a unit and are shock and thermally isolated by a low-outgassing rubber grommet. Each battery is composed of two cells. Two batteries are rated at 9 W-hr while the other two are rated at 6 W-hr, for a total of 30 W-hr on the spacecraft. Table 3: TOMSat Battery Specs Model Number Number Manufacturer Energy Stored (UL Listing) of Cells <=9 W-hr per cell ICR18650H Molicel 2 (2 batteries total) <=6 W-hr per cell IBR18650BC Molicel 2 (2 batteries total) The batteries are consumer-oriented devices. The batteries have been recognized as UL tested and approved. UL recognition has been determined through the UL Online Certifications Directory, which clearly shows that these cell batteries have undergone and passed UL Standards. Furthermore, safety devices incorporated in these batteries include pressure release valves, over-current charge protection, and over-current discharge protection. 28

GEOstare - SMC / LLNL – 3U Figure 17: CubeSat X Expanded View Overview The main mission for the satellite is to observe objects in Geostationary, or near Geostationary orbits (the GEO regime). It is supporting 3 distinct modes: Survey, Monitoring, and Custody. The latter mode is meant to track objects as they maneuver from Low Earth Orbit to GEO. CONOPS After initial on-orbit check out of the satellite to determine the state of health and various operationally relevant parameters like slew speeds and pointing stability, we will initially task the spacecraft for its Survey and Monitoring missions, and do all processing on the ground. Once this has been verified to work, we will progressively increase the level of satellite autonomy by enabling on-board processing and target scheduling. At these autonomy levels we start exercising the Custody mode as well. Materials The main structural components are aluminum 7075-T6 for the rails, and Invar-36 for the imaging payload structure. The optics are made out of high-grade fused Silica. All electronic components are COTS, including Solar Cells, with custom designed PCBs and cabling harnesses. Hazards There are no pressure vessels, hazardous or exotic materials. Batteries The electrical power storage system consists of common Li-ion batteries with over- charge/current protection circuitry (UL listing BBCV2.MH19896). 29

SHFT-1 – DARPA / STO - 3U Figure 18: SHFT 3U Cube-sat Expanded View Figure 19: SHFT 3U Cube-sat Deployed view with 3 meter HF antennas Figure 20: SHFT 3U Cube-sat Stowed configuration 30

Overview The SHFT mission will collect radio frequency signals in the HF (5-30 MHz) band to study the galactic background emissions, the HF signals from Jupiter, and the signals from terrestrial transmitters after having passed through the earth’s ionosphere. The ionosphere changes its characteristics on a minute to minute basis, particularly changing between day and night, but also in response to geomagnetic phenomena and solar events. CONOPS After deployment from the PSC CSD, the SHFT Cubesat will power up, deploy the solar panels and UHF telecom antennas, establish positive power state and wait for ground communications. Upon ground command, the HF antenna (4 tape measure type antenna, each 3 meters long) will be deployed. Over the next 3 months, the spacecraft will periodically record signals in the 5-30 MHz band for 10 minutes, then will transmit the recorded signals to the ground station on subsequent passes for analysis. Materials The primary CubeSat structure is made of Aluminum. It contains all standard commercial off the shelf (COTS) materials, electrical components, PCBs and solar cells. The deployable 3 meter HF antenna elements are made of cold rolled steel (i.e. they are standard construction tape measures). Hazards There are no pressure vessels, hazardous or exotic materials. Batteries The electrical power storage system consists of common Lithium ion batteries with over- charge/current protection circuitry in the spacecraft power controller. 31

Section 3: Assessment of Spacecraft Debris Released during Normal Operations The assessment of spacecraft debris requires the identification of any object (>1 mm) expected to be released from the spacecraft any time after launch, including object dimensions, mass, and material. The section 3 requires rationale/necessity for release of each object, time of release of each object, relative to launch time, release velocity of each object with respect to spacecraft, expected orbital parameters (apogee, perigee, and inclination) of each object after release, calculated orbital lifetime of each object, including time spent in Low Earth Orbit (LEO), and an assessment of spacecraft compliance with Requirements 4.3-1 and 4.3-2. No releases are planned on the ELaNa-19 CubeSat mission therefore this section is not applicable. 32

Section 4: Assessment of Spacecraft Intentional Breakups and Potential for Explosions. There are NO plans for designed spacecraft breakups, explosions, or intentional collisions on the ELaNa-19 mission. The probability of battery explosion is very low, and, due to the very small mass of the satellites and their short orbital lifetimes the effect of an explosion on the far-term LEO environment is negligible (ref (h)). The CubeSats batteries still meet Req. 56450 (4.4-2) by virtue of the HQ OSMA policy regarding CubeSat battery disconnect stating; “CubeSats as a satellite class need not disconnect their batteries if flown in LEO with orbital lifetimes less than 25 years.” (ref. (h)) ELaNa-19 manifest one, 6U CubeSats which are not included in the 3U or smaller mentioned in ref. (h). However, this CubeSat has protective circuitry in their designs and COTS components. ANDESITE’s EPS and battery system has over-current poly switch protection, over- current bus protection, and battery under-voltage protection built into the EPS system. The ANDESITE CubeSat use UL listed battery cells. Limitations in space and mass prevent the inclusion of the necessary resources to disconnect the battery or the solar arrays at EOM. However, the low charges and small battery cells on the CubeSat’s power system prevents a catastrophic failure, so that passivation at EOM is not necessary to prevent an explosion or deflagration large enough to release orbital debris. Assessment of spacecraft compliance with Requirements 4.4-1 through 4.4-4 shows that with a maximum cubesat lifetime of 6.2 years maximum the ELaNa-19 CubeSat is compliant. 33

Section 5: Assessment of Spacecraft Potential for On-Orbit Collisions Calculation of spacecraft probability of collision with space objects larger than 10 cm in diameter during the orbital lifetime of the spacecraft takes into account both the mean cross sectional area and orbital lifetime. The largest mean cross sectional area (CSA) among the fourteen CubeSats is that of the CubeSail CubeSat with solar sail / tether deployed (250m X 0.08m solar sail): Figure 21: CubeSail Deployed Config ∑ 𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺 𝑨𝑨𝑨𝑨𝑨𝑨𝑨𝑨 [𝟐𝟐 ∗ (𝒘𝒘 ∗ 𝒍𝒍) + 𝟒𝟒 ∗ (𝒘𝒘 ∗ 𝒉𝒉)] 𝑴𝑴𝑴𝑴𝑴𝑴𝑴𝑴 𝑪𝑪𝑪𝑪𝑪𝑪 = = 𝟒𝟒 𝟒𝟒 Equation 1: Mean Cross Sectional Area for Convex Objects (𝑨𝑨𝒎𝒎𝒎𝒎𝒎𝒎 + 𝑨𝑨𝟏𝟏 + 𝑨𝑨𝟏𝟏 ) 𝑴𝑴𝑴𝑴𝑴𝑴𝑴𝑴 𝑪𝑪𝑪𝑪𝑪𝑪 = 𝟐𝟐 Equation 2: Mean Cross Sectional Area for Complex Objects All CubeSats evaluated for this ODAR are stowed in a convex configuration, indicating there are no elements of the CubeSats obscuring another element of the same CubeSats from view. Thus, mean CSA for all stowed CubeSats was calculated using Equation 1. This configuration renders the longest orbital life times for all CubeSats. Once a CubeSat has been ejected from the P-POD and deployables have been extended Equation 2 is utilized to determine the mean CSA. Amax is identified as the view that yields the maximum cross-sectional area. A1 and A2 are the two cross-sectional areas orthogonal to Amax. Refer to Appendix D for component dimensions used in these calculations The CubeSail (3.52 kg) orbit at deployment is 500km apogee altitude by 500 km perigee altitude, with an inclination of 85 degrees. With an area to mass ratio of 2.853 m2/kg, DAS yields < 0.1 years for orbit lifetime for its deployed state, which in turn is used to obtain the collision probability. Even with the variation in CubeSat design and orbital 34

lifetime ELaNa-19 CubeSats see an average of 0.00000 probability of collision. All CubeSats on ELaNa-19 were calculated to have a probability of collision of 0.00000. Table 4 below provides complete results. There will be no post-mission disposal operation. As such the identification of all systems and components required to accomplish post-mission disposal operation, including passivation and maneuvering, is not applicable. 35

Table 4: CubeSat Orbital Lifetime & Collision Probability Stowed Deployed Mean C/S Area-to Orbital Probability of Area-to Orbital Probability of CubeSat Mass (kg) Area (m^2) Mass (m^2/kg) Lifetime (yrs) collision (10^X) Mean C/S Area (m^2) Mass (m^2/kg) Lifetime (yrs) collision (10^X) ANDESITE 5.13 0.0763 0.0149 4.6 0.00000 0.1083 0.021 4.2 0.00000 CeREs 4.56 0.0390 0.0086 5.4 0.00000 0.0735 0.016 4.5 0.00000 CHOMPTT 1.56 0.0390 0.0250 4.0 0.00000 0.0415 0.027 4 0.00000 CubeSail 3.52 0.0362 0.0103 5.1 0.00000 10.0364 2.853 <0.1 0.00000 DaVinci 3.36 0.0459 0.0136 4.6 0.00000 0.1006 0.030 3.9 0.00000 ISX 3.70 0.0442 0.0120 4.8 0.00000 0.0445 0.012 4.8 0.00000 NMTSat 1.58 0.0417 0.0264 4.0 0.00000 0.0493 0.031 3.9 0.00000 Rsat 4.15 0.0449 0.0108 5.0 0.00000 0.0629 0.015 4.5 0.00000 Shields-1 6.94 0.0417 0.0060 6.2 0.00000 0.0494 0.007 5.8 0.00000 STF-1 3.35 0.0467 0.0139 4.6 0.00000 0.0490 0.015 4.6 0.00000 TOMSat 4.09 0.0406 0.0099 5.1 0.00000 0.0635 0.016 4.5 0.00000 EAGLESCOUT TOMSat R3 4.09 0.0406 0.0099 5.1 0.00000 0.0635 0.016 4.5 0.00000 GEOStare 3.99 0.0443 0.0111 5.0 0.00000 0.0880 0.022 4.1 0.00000 SHFT-1 5.10 0.0476 0.0093 5.2 0.00000 0.1855 0.036 3.7 0.00000 Solar Flux Table Dated 11/07/2016

The probability of any ELaNa-19 spacecraft collision with debris and meteoroids greater than 10 cm in diameter and capable of preventing post-mission disposal is less than 0.00000, for any configuration. This satisfies the 0.001 maximum probability requirement 4.5-1. Since the CubeSats have no capability or plan for end-of-mission disposal, requirement 4.5-2 is not applicable. Assessment of spacecraft compliance with Requirements 4.5-1 shows ELaNa-19 to be compliant. Requirement 4.5-2 is not applicable to this mission. Section 6: Assessment of Spacecraft Postmission Disposal Plans and Procedures All ELaNa-19 spacecraft will naturally decay from orbit within 25 years after end of the mission, satisfying requirement 4.6-1a detailing the spacecraft disposal option. Planning for spacecraft maneuvers to accomplish postmission disposal is not applicable. Disposal is achieved via passive atmospheric reentry. Calculating the area-to-mass ratio for the worst-case (smallest Area-to-Mass) post- mission disposal among the CubeSats finds Shields-1 in its stowed configuration as the worst case. The area-to-mass is calculated for is as follows: 𝑴𝑴𝑴𝑴𝑴𝑴𝑴𝑴 𝑪𝑪�𝑺𝑺 𝑨𝑨𝑨𝑨𝑨𝑨𝑨𝑨 (𝒎𝒎𝟐𝟐 ) 𝒎𝒎𝟐𝟐 = 𝑨𝑨𝑨𝑨𝑨𝑨𝑨𝑨 − 𝒕𝒕𝒕𝒕 − 𝑴𝑴𝑴𝑴𝑴𝑴𝑴𝑴 ( ) 𝑴𝑴𝑴𝑴𝑴𝑴𝑴𝑴 (𝒌𝒌𝒌𝒌) 𝒌𝒌𝒌𝒌 Equation 3: Area to Mass 0.0417𝑚𝑚2 𝑚𝑚2 = 0.0060 6.94𝑘𝑘𝑘𝑘 𝑘𝑘𝑘𝑘 Shields-1 has the smallest Area-to-Mass ratio and as a result will have the longest orbital lifetime. The assessment of the spacecraft illustrates they are compliant with Requirements 4.6-1 through 4.6-5. DAS 2.0.2 Orbital Lifetime Calculations: DAS inputs are: 500 km maximum apogee 500 km maximum perigee altitudes with an inclination of 85 degrees at deployment no earlier than November 2017. An area to mass ratio of 0.0060 m2/kg for the Shields-1 CubeSat was imputed. DAS 2.0.2 yields a 6.2 years orbit lifetime for Shields-1 in its stowed state. This meets requirement 4.6-1. For the complete list of CubeSat orbital lifetimes reference Table 4: CubeSat Orbital Lifetime & Collision Probability. Assessment results show compliance.

Section 7: Assessment of Spacecraft Reentry Hazards A detailed assessment of the components to be flown on ELaNa-19 was performed. The assessment used DAS 2.0, a conservative tool used by the NASA Orbital Debris Office to verify Requirement 4.7-1. The analysis is intended to provide a bounding analysis for characterizing the survivability of a CubeSat’s component during re-entry. For example, when DAS shows a component surviving reentry it is not taking into account the material ablating away or charring due to oxidative heating. Both physical effects are experienced upon reentry and will decrease the mass and size of the real-life components as the reenter the atmosphere, reducing the risk they pose still further. The following steps are used to identify and evaluate a components potential reentry risk relative to the 4.7-1 requirement of having less than 15 J of kinetic energy and a 1:10,000 probability of a human casualty in the event the survive reentry. 1. Low melting temperature (less than 1000 °C) components are identified as materials that would never survive reentry and pose no risk to human casualty. This is confirmed through DAS analysis that showed materials with melting temperatures equal to or below that of copper (1080 °C) will always demise upon reentry for any size component up to the dimensions of a 1U CubeSat. 2. The remaining high temperature materials are shown to pose negligible risk to human casualty through a bounding DAS analysis of the highest temperature components, stainless steel (1500°C). If a component is of similar dimensions and has a melting temperature between 1000 °C and 1500°C, it can be expected to posses the same negligible risk as stainless steel components. See Table 5 through Table 7. Table 5: ELaNa-19 High Melting Temperature Material Analysis (1/3) CubeSat High Temp Component Material Mass (g) Demise Alt (km) KE (J) ANDESITE Node Deployment Springs Steel AISI 304 0.002 76.4 0 ANDESITE Antennae Steel AISI 410 0.001 0 0 ANDESITE 6-32 Screws Stainless Steel (generic) 0.000 77.5 0 ANDESITE 2-56 Screws Stainless Steel (generic) 0.000 77.4 0 ANDESITE Hinges Stainless Steel (generic) 0.006 0 1 CeREs Tungsten Tube Tungsten 0.202 0 150 CeREs Detector Silicon 0.008 0 0 CeREs Closeout Plate 1 Tungsten 0.018 0 8 CHOMPTT StenSat UHF Antennae Stainless Steel (generic) 0.001 0 0 CHOMPTT Lithium UHF Antennae Stainless Steel (generic) 0.001 0 0 CHOMPTT Backplane Holder - 11 mm Steel AISI 304 0.002 0 0 CHOMPTT Backplane Holder - 13 mm Steel AISI 304 0.002 0 0 CHOMPTT Reaction Wheel Assembly Stainless Steel (generic) 0.096 68.6 0 38

Table 6: ELaNa-19 High Melting Temperature Material Analysis (2/3) CubeSat High Temp Component Material Mass (g) Demise Alt (km) KE (J) CHOMPTT Batteries Stainless Steel (generic) 0.045 69 0 CHOMPTT Battery Holder Plates 2a&2b Steel AISI 304 0.117 0 25 CHOMPTT Lithium Radio Stainless Steel (generic) 0.026 0 6 CHOMPTT Retoreflector Array Stainless Steel (generic) 0.018 0 4 CubeSail CubeSail Antenna Stainless Steel (generic) 4.400 74.7 0 CubeSail Fasteners Stainless Steel (generic) 100.000 77.7 0 CubeSail Low-head Socket Cap Screw Stainless Steel (generic) 0.680 77 0 CubeSail Wave Spring Steel AISI 304 0.045 77.9 0 CubeSail SRU Nut Plate Stainless Steel (generic) 7.530 75.3 0 CubeSail Wave Spring 2 Steel AISI 304 0.045 77.8 0 CubeSail Motor Pin Steel A-286 0.091 77.6 0 CubeSail Socket Cap Screw Stainless Steel (generic) 0.454 77.3 0 CubeSail Socket Cap Screw 2 Stainless Steel (generic) 0.771 77.1 0 CubeSail Bobbin Motor Bearing Stainless Steel (generic) 1.000 76.7 0 CubeSail Drive Pin Steel A-286 0.272 77.2 0 CubeSail Socket Cap Screw 3 Stainless Steel (generic) 0.635 77.3 0 ISX Historesis Material Stainless Steel (generic) 0.0015 77 0 ISX Screw - Representative Stainless Steel (generic) 0.00045 76.9 0 ISX Structural Rods Stainless Steel (generic) 0.001 77.4 0 ISX ISIS screws Stainless Steel (generic) 0.00025 77.1 0 ISX ISIS washers Stainless Steel (generic) 0.00005 0 0 ISX GAMMA Antenna washers Stainless Steel (generic) 0.00005 0 0 ISX GAMMA Antenna screws Stainless Steel (generic) 0.0006 76.2 0 ISX GAMMA Antenna nuts Stainless Steel (generic) 0.00001 0 0 ISX solar panel screw Stainless Steel (generic) 0.00054 76.6 0 ISX solar panel nut Stainless Steel (generic) 0.000241 0 0 ISX Solar panel clip Stainless Steel (generic) 0.0005 0 0 ISX 15mm spacers Stainless Steel (generic) 0.002 75 0 ISX 25mm spacers Stainless Steel (generic) 0.005 73.5 0 Rsat Motors Stainless Steel (generic) 0.01933 73.3 0 Rsat ADCS Stainless Steel (generic) 0.01 0 3 Rsat Fasteners Stainless Steel (generic) 0.00005 77.6 0 Shields-1 Shield1 Titanium (6 Al-4 V) 0.072364523 0 14 Shields-1 Shield1 Tantalum 0.2 0 69 Shields-1 Shield2 Titanium (6 Al-4 V) 0.072364523 0 14 Shields-1 Shield3 Tantalum 0.1 0 27 Shields-1 Shield4 Titanium (6 Al-4 V) 0.00001 0 0 Shields-1 Shield5 Tantalum 0.00001 0 0 Shields-1 Shield6 Titanium (6 Al-4 V) 0.0001 0 0 Shields-1 Shield7 Titanium (6 Al-4 V) 0.0001 0 0 39

Table 7: ELaNa-19 Summary of Surviving High Temperature Material Components (3/3) CubeSat High Temp Component Material Mass (g) Demise Alt (km) KE (J) Shields-1 Shield8 Titanium (6 Al-4 V) 0.0001 0 0 Shields-1 Charge Dissipation Film electrodes Steel AISI 304 0.01 73.8 0 Shields-1 Charge Dissipation Film spring Stainless Steel (generic) 0.0025 76.1 0 Shields-1 RTDs (Est Dims) Stainless Steel (generic) 0.001 77.5 0 Shields-1 Fasterners2 Stainless Steel (generic) 0.0001 77.7 0 Shields-1 Fasteners3 Stainless Steel (generic) 0.00005 77.7 0 Shields-1 Fasteners4 Stainless Steel (generic) 0.0005171 0 0 Shields-1 Solar Panel Screws Steel AISI 410 0.00008 77.6 0 Shields-1 Solar Panel Washers Steel AISI 410 0.0001 0 0 Shields-1 Remove Before Flight Pin Stainless Steel (generic) 0.02 73.7 0 Shields-1 Sep Switch Stainless Steel (generic) 0.02 73.7 0 Shields-1 ADCS Components (Hysteresis Rods) Stainless Steel (generic) 0.001 77.5 0 STF-1 Ferrite Bead Stainless Steel (generic) 0.00001 77.3 0 STF-1 Geiger Tube Stainless Steel (generic) 0.05 67 0 STF-1 Fasteners5 Stainless Steel (generic) 0.00001 77.9 0 TOMSat Reaction Wheels Stainless Steel (generic) 0.22501 63.9 0 TOMSat Single Torque Rod Stainless Steel (generic) 0.01844 74.8 0 TOMSat 18267 Titanium (generic) 0.01669 0 2 TOMSat 18265 Titanium (generic) 0.01092 0 1 TOMSat 18264 Titanium (generic) 0.01232 0 1 TOMSat 18268 Titanium (generic) 0.00404 0 0 TOMSat 18266 Titanium (generic) 0.01028 0 2 TOMSat 18263 Titanium (generic) 0.00128 0 0 TOMSat 18270 Titanium (generic) 0.00074 0 0 TOMSat Laser Aluminum 6061-T6 0.35285 72.8 0 GEOstare Batteries-GEOStae Stainless Steel (generic) 0.00783 0 1 GEOstare Telescope baffle Titanium (generic) 0.0961 0 22 GEOstare Telescope Stainless Steel (generic) 0.62 65.4 0 GEOstare Fasteners7 Steel A-286 0.0000025 78 0 SHFT-1 Internal Fasteners Stainless Steel (generic) 0.0005 77 0 SHFT-1 External Fasteners Stainless Steel (generic) 0.0005 77 0 The majority of high temperature components demise upon reentry. And all CubeSats comply with the 1:10,000 probability of Human Casualty Requirement 4.7-1. A breakdown of the determined probabilities follows on Table 7. 40

Table 8: Requirement 4.7-1 Compliance by CubeSat CubeSat Risk Risk < 1:10,000 ANDESITE 1:0 Compliant CeREs 1:210,600 Compliant CHOMPTT 1:93,400 Compliant CubeSail 1:0 Compliant DaVinci 1:0 Compliant ISX 1:0 Compliant NMTsat 1:0 Compliant Rsat 1:0 Compliant Shields-1 1:32,400 Compliant STF-1 1:0 Compliant TOMSat 1:0 Compliant GEOstare 1:200,000 Compliant SHFT-1 1:0 Compliant *Requirement 4.7-1 Probability of Human Casualty > 1:10,000 If a component survives to the ground but has less than 15 Joules of kinetic energy it is not included in the Debris Casualty Area that inputs into the Probability of Human Casualty calculation. Which is why CubeSats that have surviving components like ANDESITE, CubeSail, DaVinci, ISX, NMTsat Rsat, STF-1 TOMSat EAGLESCOUT, TOMSat R3, and SHFT-1 have a 1:0 probability as none of their components have more than 15J of energy. The breakdown of CubeSat’s with greater than 15J of energy components is as follows: CeREs has 1, CHOMPTT has1, Shields-1 has 3, and GEOStare has 1. All CubeSats launching under the ELaNa-19 mission are shown to be in compliance with Requirement 4.7-1 of NASA-STD-8719.14A. See the Appendix for a complete accounting of the survivability of all CubeSat components. 41

Section 8: Assessment for Tether Missions In the ELaNa-19 mission, CubeSail’s deployable sail made of a mylar film qualifies as a momentum tether although a ribbon would be a more accurate description of its dimensions (0.0004 cm x 7.9cm x 25,317 cm). The tether mission plan can be referenced in the CubeSail specific mission plan located in Section 2. Following the Methods to Assess Compliance for Tethered Systems (section 4.8.4), the DAS analysis determined the CubeSail design to be COMPLIANT with both Requirement 4.5-1 and 4.5-2 dealing with meeting the requirements limiting the generation or orbital debris from on-orbit collisions. The probability of collision on orbit for the un-deployed system, fully deployed system, and ½ the system in the event of a tether severing event was calculated to be << 0.001. CubeSail is also compliant with Requirements 4.6-1 to 4.6-4 (Postmission Disposal), given the low 500km x 500km, this orbit will have CubeSail passively deorbit in 5.5 years if the system does not deploy, <<0.1 years if the system does deploy, and <<0.1 year if the tether breaks into two equal parts as calculated via DAS 2.0.2. All three scenarios are compliant with the Requirement 4.6-1 to 4.6-4. Figure 22: Tether Assessment of CubeSail ELaNa-19 CubeSat, CubeSail satisfies Section 8’s requirement 4.8-1. 42

Section 9-14 ODAR sections 9 through 14 for the launch vehicle are not covered here. If you have any questions, please contact the undersigned at 321-867-2958. /original signed by/ Justin Treptow Flight Design Analyst NASA/KSC/VA-H1 cc: VA-H/Mr. Carney VA-H1/Mr. Beaver VA-H1/Mr. Haddox VA-G2/Mr. Atkinson VA-G2/Mr. Marin SA-D2/Mr. Frattin SA-D2/Mr. Hale SA-D2/Mr. Henry Analex-3/Mr. Davis Analex-22/Ms. Ramos 43

Appendix Index: Appendix A. ELaNa-19 Component List by CubeSat: ANDESITE Appendix B. ELaNa-19 Component List by CubeSat: CeREs Appendix C. ELaNa-19 Component List by CubeSat: CHOMPTT Appendix D. ELaNa-19 Component List by CubeSat: CubeSail Appendix E. ELaNa-19 Component List by CubeSat: DaVinci Appendix F. ELaNa-19 Component List by CubeSat: ISX Appendix G. ELaNa-19 Component List by CubeSat: NMTSat Appendix H. ELaNa-19 Component List by CubeSat: RSat Appendix I. ELaNa-19 Component List by CubeSat: Shields-1 Appendix J. ELaNa-19 Component List by CubeSat: STF-1 Appendix K. ELaNa-19 Component List by CubeSat: TOMSat EAGLESCOUT Appendix L. ELaNa-19 Component List by CubeSat: TOMSat R3: Appendix M. ELaNa-19 Component List by CubeSat: GEOStare: Appendix N. ELaNa-19 Component List by CubeSat: SHFT-1 44

Appendix A. ELaNa-19 Component List by CubeSat: ANDESITE Diameter/ Row Individual Length Height High Melting CUBESAT Name Qty Material Body Type Width Survivability Number Mass (g) (mm) (mm) Temp Temp (mm) ANDESITE 1 6U Anodized Baseplate 1 Aluminum 7075 Flate Plate 1346 239 361 6.35 No - Demise ANDESITE 2 Sensor Node Structure 8 Alumnium 6061 Box 133 97.81 190 15.5 No - Demise ANDESITE 3 Top Plate 1 Aluminum 6061 Box 364 227.8 361 3.18 No - Demise ANDESITE 4 CubeSat Structure - 2U L Brackets 2 Aluminum 6061 Box 60 19.05 223.23 3.18 No - Demise ANDESITE 5 CubeSat Structure - 1U L Brackets 4 Aluminum 6061 Box 36 19.05 93.65 3.18 No - Demise ANDESITE 6 CubeSat Structure - 1U Cladding 2 Aluminum 6061 Box 38 227.8 100 2.29 No - Demise ANDESITE 7 CubeSat Structure - 2U Cladding 2 Aluminum 6061 Box 110 148.6 100 2.29 No - Demise ANDESITE 8 Top Solar Panel 1 Fiberglass Cylinder 150 227.8 361 No - Demise ANDESITE 9 Wing Solar Panel 2 Fiberglass Box 98 354.86 86 3.18 No - Demise ANDESITE 10 Node Deployment Mechanism 1 Aluminum 6061 Flat Plate 1549 210 151.33 15 No - Demise ANDESITE 11 Node Deployment Peg Guides 4 Aluminum 6061 Box 82 27.6 100 15 No - Demise ANDESITE 12 Node Deployment Springs 8 Steel 302 Cylinder 4.4 4.7752 19.05 Yes 1538 See Tables 4-6 ANDESITE 13 Antennae 9 Steel 410 Blade 0.8 12.7 165.1 1 Yes 1532 See Tables 4-6 ANDESITE 14 Sensor Node Solar Panels 16 Fiberglass PCB 67.3 175 93.73 2 No - Demise ANDESITE 15 Mule Battery 1 Battery Box 260.4 95 90 39.82 No - Demise ANDESITE 16 Node Batteries 8 Battery Box 184.4 59.5 157 9.8 No - Demise ANDESITE 17 EPS 1 Fiberglass (PCB) Board 174 96 90 1.5 No - Demise ANDESITE 18 ADCS Components (eg. Magnets) 1 Fiberglass (PCB) Board 94.2 96 90 1.5 No - Demise ANDESITE 19 Comm Board 1 Fiberglass (PCB) Board 125 96 90 1.5 No - Demise ANDESITE 20 C&DH Board 1 Fiberglass (PCB) Board 142 96 90 1.5 No - Demise ANDESITE 21 Magnetometer Orthogonal Holder 1 Macor Holder 5 5 5 5 No - Demise ANDESITE 22 Magnetorquers 1 Copper Board/Coils 95.9 96 90 1.5 No - Demise ANDESITE 23 6-32 Screws 90 Stainless Steel 316 Screws 0.5 3.5052 6.35 Yes 1400 See Tables 4-6 ANDESITE 24 2-56 Screws 150 Stainless Steel 316 Screws 0.3 2.1844 6.35 Yes 1400 See Tables 4-6 ANDESITE 25 Bumpers 4 Nylon Blocks 2 25.4 50.8 2.54 No - Demise ANDESITE 26 Hinges 4 Stainless Steel 316 Hinge 12 25.4 50.8 0.889 Yes See Tables 4-6

Appendix B. ELaNa-19 Component List by CubeSat: CeREs Diameter/ Row Individual Length Height High Melting CUBESAT Name Qty Material Body Type Width Survivability Number Mass (g) (mm) (mm) Temp Temp (mm) Ceres 1 Cubesat Structure 1 Aluminium 6061-T6 Box 700 100 100 340 No - Demise Ceres 2 Payload Structure 1 Aluminium 6061-T6 Box 250 74 52 94 No - Demise Ceres 3 Tungsten Tube 1 Tungsten Cylinder 202 67 40 Yes 3422 See Tables 4-6 Ceres 4 XB1 1 Aluminum Box 1800 100 100 135 No - Demise Ceres 5 solar array 2 FR4+Aluminum Flat Plate 194 65 82 327 No - Demise Ceres 6 Detector 8 Silicon Cylinder 8 39 39 Yes 1410 See Tables 4-6 Ceres 7 Closeout Plate 1 2 Tungsten Flat Plate 25 50 14 2 Yes 3422 See Tables 4-6 Ceres 8 Aluminum Closeout Plate Holder 1 Aluminum Box 20 26 67 17.2 No - Demise Ceres 9 Detector Holder 16 FR4 Flat Plate 5 52 52 No - Demise Ceres 10 Payload Card 4 FR4+Copper Flat Plate 100 88 92 18 No - Demise Ceres 11 backplane 1 FR4+Copper Flat Plate 21 7.5 25.4 11.3 No - Demise Ceres 12 HVPS 2 Urethane? Box 20 33 40.6 12.1 No - Demise Ceres 13 GPS antenna 1 Aluminum 6061-T6 Flat Plate 50 53 18 No - Demise Ceres 14 ISIS antenna 4 Aluminum 6061-T6 Flat Plate 100 98 98 5.7 No - Demise Ceres 15 CSP 1 FR4+Copper Flat Plate 44 100 100 14.6 No - Demise Ceres 16 Cabling 6 copper alloy cylinder 8 2 6 No - Demise 46

Appendix C. ELaNa-19 Component List by CubeSat: CHOMPTT (1/2) Diameter/ Row Individual Length Height High Melting CUBESAT Name Qty Material Body Type Width Survivability Number Mass (g) (mm) (mm) Temp Temp (mm) CHOMPTT 1 3U CubeSat Chassis 1 Aluminum 5052 Box 317 100 100 339.89 No - Demise CHOMPTT 2 StenSat UHF Antennae 1 Stainless Steel (generic) Box 1.43 12.2 186.5 0.1 Yes 1510 See Tables 4-6 CHOMPTT 3 Lithium UHF Antennae 1 Stainless Steel (generic) Box 1.43 12.2 195.6 0.1 Yes 1510 See Tables 4-6 CHOMPTT 4 RBF Switch 1 Polycarbonate (aka Lexan) Box 1.15 12.27 19.84 6.39 No - Demise CHOMPTT 5 Rail Switches 1 Polycarbonate (aka Lexan) Box 1 13 15 10 No - Demise CHOMPTT 6 GPS Patch Antennae 1 Fiberglass Flat Plate 9.2 34.94 89.5 - No - Demise CHOMPTT 7 Sun Sensors 5 Aluminum 6061 Box 4 27.4 14 5.9 No - Demise CHOMPTT 8 1U TASC Solar Panel 5 Aluminum (generic) Flat Plate 108.18 98.6 98.99 - No - Demise CHOMPTT 9 1U GOMspace Solar Panel 4 Aluminum (generic) Flat Plate 57 98 82.6 - No - Demise CHOMPTT 10 1U GOMspace Solar Panel 4 Aluminum (generic) Flat Plate 26 98 82.6 - No - Demise CHOMPTT EDSN/NODeS-derived Spacecraft Bus - - - CHOMPTT 11 Backplane PCB 1 Fiberglass Flat Plate 29.759 56.94 140.96 - No - Demise CHOMPTT 12 Backplane Holder - 11 mm 1 Steel AISI 304 Box 1.52 11 67 0.9 Yes 1538 See Tables 4-6 CHOMPTT 13 Backplane Holder - 13 mm 1 Steel AISI 304 Box 1.99 16 67 0.9 Yes 538 See Tables 4-6 CHOMPTT 14 Midplane 1 Aluminum 6061-T6 Cylinder 3.14 16.9 21.1 - No - Demise CHOMPTT 15 Router PCB 1 Fiberglass Flat Plate 44.74 60.63 89.74 - No - Demise CHOMPTT 16 ACS PCB 1 Fiberglass Flat Plate 36.94 94.09 95.46 22.77 No - Demise CHOMPTT 17 Reaction Wheel Assembly 1 Stainless Steel (generic) Box 96.43 26 66 26 Yes 1400 See Tables 4-6 CHOMPTT 18 Phone PCB 1 Fiberglass Box 51.86 94.09 109.77 30.6 No - Demise CHOMPTT 19 EPS PCB 1 Fiberglass Box 46.57 94.09 95.46 37.53 No - Demise 47

ELaNa-19 Component List by CubeSat: CHOMPTT (2/2) Diameter/ Row Individual Length Height High Melting CUBESAT Name Qty Material Body Type Width Survivability Number Mass (g) (mm) (mm) Temp Temp (mm) CHOMPTT 20 Lithium Grounding Hat Assembly 1 Aluminum 6061-T6 Box 1.84 18.13 52.64 5.8 No - Demise CHOMPTT 21 StenSat Grounding Hat Assembly 1 Aluminum 6061-T6 Box 1.32 17 43 5 No - Demise CHOMPTT 22 Batteries 4 Stainless Steel (generic) Cylinder 45.45 18.3 64.9 - Yes 1400 See Tables 4-6 CHOMPTT 23 Battery Holder 1 Polycarbonate (aka Lexan) Box 27.99 78.73 82.6 15.7 No - Demise CHOMPTT 24 Battery Holder Plates 2a&2b 2 Steel AISI 304 Flat Plate 117.07 94.09 95.46 - Yes 1450 See Tables 4-6 CHOMPTT 25 StenSat Radio Assembly 1 Fiberglass Box 28.87 44.45 78.74 18.53 No - Demise CHOMPTT 26 GPS PCB 1 Fiberglass Flat Plate 48.14 94.09 95.5 - No - Demise CHOMPTT 27 GPS Housing & Heat Sink 1 Aluminum 6061-T6 Flat Plate 32.9 87.01 92.55 - No - Demise CHOMPTT 28 GPS Reciever 1 Fiberglass Box 18.3 45.72 71.12 10.19 No - Demise CHOMPTT 29 Lithium Radio PCB 1 Fiberglass Flat Plate 28.72 94.909 95.46 - No - Demise CHOMPTT 30 Lithium Radio 1 Stainless Steel (generic) Box 25.7 32 62 10.079 Yes 1450 See Tables 4-6 CHOMPTT 31 Adapter Plate - Aluminum 6061 Flat Plate 40.15 97 97 - No - Demise CHOMPTT OPTI Payload - - - CHOMPTT 32 Payload Structure 1 Aluminum 6061 Box 564.83 96.4 97 94 No - Demise CHOMPTT 33 Supervisor PCB 1 Fiberglass Box 30.6 86.28 56.12 - No - Demise CHOMPTT 34 Channel PCB 2 Fiberglass Flat Plate 30 86.15 86.01 - No - Demise CHOMPTT 35 High Voltage Shield 2 Aluminum 6061, Cesium Flat Plate 45.79 84.75 61.75 11.5 No - Demise CHOMPTT 36 CSAC (Chipscale Atomic Clock) 2 Aluminum 6061 Box 35 35.57 40.65 11.43 No - Demise CHOMPTT 37 Beacon Diode PCB 1 Fiberglass Box 35 12 30.13 - No - Demise CHOMPTT 38 Retoreflector Array Fused Silica (Glass) Box 17.98 52 30 7 Yes 1600 See Tables 4-6 CHOMPTT 39 Fasteners - - - - - - - No - Demise CHOMPTT 40 Cabling - - - - - - - No - Demise CHOMPTT 41 Large Aperature Plate (-Y) 1 Aluminum 6061 Flat Plate 37 99.78 99.75 - No - Demise 48

Appendix D. ELaNa-19 Component List by CubeSat: CubeSail (1/3) Diameter/ Row Individual Length Height High Melting CUBESAT Name Qty Material Body Type Width Survivability Number Mass (g) (mm) (mm) Temp Temp (mm) CubeSail 1 Rail 8 Aluminum 6061 Rail 26.8 17 17 155.75 No - Demise CubeSail 2 Bottom Plate 2 Aluminum 6061 Plate 71.97 100 100 25.5 No - Demise CubeSail 3 Antennae 8 Stainless Steel Strip 4.4 6.7 22 0.4 Yes 1450 See Tables 4-6 CubeSail 4 Radiation Shielding 6 Aluminum 6061 Plate 35.6 80 161.75 1.016 No - Demise Radiation Shielding with Access CubeSail 5 2 Aluminum 6061 Plate 35.2 80 161.75 1.016 No - Demise Port CubeSail 6 Solar Cell 22 Solar Cell Panel 3.2 40 70 0.4 No - Demise CubeSail 7 Flex Cable 8 Kapton and PCB Components Flat Cable 5 54 18.34 169.32 No - Demise CubeSail 8 Magnetometer 8 Circuit Board Board 3.7 40 30 3.9 No - Demise CubeSail 9 Daughter Card 2 Circuit Board Plate 10.1 60 30 2.41 No - Demise CubeSail 10 Power Board 2 Circuit Board Board 56.5 94 90 1.5 No - Demise CubeSail 11 C&DH Board (was CPU) 2 Circuit Board Board 40 90 90 5.6002 No - Demise Aluminum 6061 and Circuit CubeSail 12 Lithium Radio 2 Plate 50 60.4 30.4 9 No - Demise Board CubeSail 13 Radio Carry Board 2 Circuit Board Board 17.3 70 70 1.6 No - Demise CubeSail 14 Payload Board 2 Circuit Board Board 30.3 12 90 90 No - Demise CubeSail 15 Connector Adjustment Board 2 Circuit Board Board 3 5 32 20 No - Demise CubeSail 16 Torque Coil 10 Circuit Board Board 27.7 90 76.2 3.5 No - Demise CubeSail 17 Middle Plate 2 Aluminum 6061 Plate 66.98 96.83 96.83 13.5 No - Demise Lithium Ion Batteries, Circuit 4 cylinders, mounted CubeSail 18 Battery Pack 2 227.2 87 85 22.5 No - Demise Board on board CubeSail 19 Battery Holder 2 Aluminum 6061 Board 40 86 86.5 22.8 No - Demise CubeSail 20 Fasteners 1 Stainless Steel Small 100 Yes 1450 See Tables 4-6 49

ELaNa-19 Component List by CubeSat: CubeSail (2/3) Diameter/ Row Body Individual Length Height High Melting CUBESAT Name Qty Material Width Survivability Number Type Mass (g) (mm) (mm) Temp Temp (mm) CubeSail 21 Cabling 1 Copper alloy, teflon insulation Wires 150 No - Demise CubeSail 22 Bobbin 2 Al 6061 Cylinder 93.5760296 49.022 84.00034 0 No - Demise CubeSail 23 Motor Mount Plate, Drive Shaft 2 Al 6061 Cylinder 5.3070264 25.4 6.985 0 No - Demise CubeSail 24 Motor Mount Plate, Ribbon Cable 2 Al 6061 Cylinder 6.2142104 25.4 6.985 0 No - Demise CubeSail 25 Motor Support Rod 6 Al 6061 Rod 2.26796 4.7625 50.8 0 No - Demise CubeSail 26 Drive Wheel 2 Al 6061 Cylinder 7.257472 26.9494 8.30834 0 No - Demise CubeSail 27 Shim Rings 4 Al 6061 Ring 0.4989512 26.9494 1.5748 0 No - Demise CubeSail 28 A-Frame, Motor Mount 2 Al 6061 Plate 19.4590968 57.00014 13.4839964 49.9999 No - Demise CubeSail 29 A-Frame, Support 2 Al 6061 Plate 22.8156776 57.00014 13.4919974 49.9999 No - Demise CubeSail 30 Support Rod 4 Al 6061 Rod 36.28736 4.7625 78.3844 0 No - Demise CubeSail 31 Film 2 Aluminized Mylar Sheet 85 79 253170 0.004 No - Demise CubeSail 32 Low-head Socket Cap Screw 8 18-8 stainless steel Screw 0.680388 5.7404 8.1788 0 Yes 1450 See Tables 4-6 CubeSail 33 Slit Rod 2 Al 6061 - T6 Rod 2.9937072 6.35 79 0 No - Demise CubeSail 34 Standoff Feet 4 Brass Screw 0.1360776 3.7084 1.4732 0 No - Demise CubeSail 35 (Motor) Payload Plate, Male 1 Al 6061 Plate 54.43104 16.4999924 99.9998 99.9998 No - Demise CubeSail 36 Camera Mount Dog 1 Al 6061 Block 8.618248 29.972 10.8204 19.9898 No - Demise CubeSail 37 Camera Mount Base 1 Al 6061 Block 8.2553744 19.9898 29.972 7.33298 No - Demise CubeSail 38 Motor Mount Plate 1 Al 6061 Plate 1.9504456 21.2015578 13.9338304 2.54 No - Demise CubeSail 39 Motor Support Rod 4 Al 2024 Rod 1.4061352 3.96875 47.54118 0 No - Demise CubeSail 40 SRU Leadscrew 1 Brass Screw 3.628736 6.1849 15.986506 0 No - Demise 50

ELaNa-19 Component List by CubeSat: CubeSail (3/3) Diameter/ High Row Body Individual Length Height Melting CUBESAT Name Qty Material Width Tem Survivability Number Type Mass (g) (mm) (mm) Temp (mm) p CubeSail 41 Compression Spring 2 Zinc-coated Music Wire Spring 0.226796 7.9193136 18.1991 0 No - Demise CubeSail 42 Motor 2 Brass Cylinder 75.1 15.93 61.54 0 No - Demise See Tables 4- CubeSail 43 Wave Spring 2 302 Stainless Steel Ring 0.0453592 4.6736 0.5842 0 Yes 1450 6 CubeSail 44 Slit Rod 2 Al 6061 - T6 Rod 2.9937072 6.35 79 0 No - Demise CubeSail 45 Payload Plate, Female 1 Al 6061 Plate 49.89512 19.2499996 99.9998 99.9998 No - Demise CubeSail 46 Camera Mount Dog 1 Al 6061 Block 8.618248 29.972 10.8204 19.9898 Demise CubeSail 47 Camera Mount Base 1 Al 6061 Block 8.2553744 19.9898 29.972 7.33298 No - Demise See Tables 4- CubeSail 48 SRU Nut Plate 1 Stainless Steel Plate 7.5296272 26.4922 12.7 3.175 Yes 1430 6 CubeSail 49 Motor 1 Brass Cylinder 75.1 15.93 61.54 0 No - Demise See Tables 4- CubeSail 50 Wave Spring 2 302 Stainless Steel Ring 0.0453592 4.6736 0.5842 0 Yes 1450 6 See Tables 4- CubeSail 51 Motor Pin 1 Steel Cylinder 0.0907184 1.6764 6.1341 Yes 1450 6 See Tables 4- CubeSail 52 Socket Cap Screw 12 18-8 stainless steel Screw 0.453592 5.4102 7.8486 0 Yes 1450 6 See Tables 4- CubeSail 53 Socket Cap Screw 6 18-8 stainless steel Screw 0.7711064 4.4958 13.716762 0 Yes 1450 6 CubeSail 54 SRU Frame Screws 8 Brass Screw 0.2721552 3.429 9.271 0 No - Demise See Tables 4- CubeSail 55 Bobbin Motor Bearing 6 Stainless Steel Ring 1 3 3 0 Yes 1450 6 See Tables 4- CubeSail 56 Drive Pin 2 Steel Cylinder 0.2721552 3.175 4.7625 0 Yes 1450 6 CubeSail 57 LED mount board 4 Circuit Board Plate 0.5 1.524 36.83 18.415 No - Demise CubeSail 58 3.2x2.4mm LED 6 LED Block 0 3.1496 2.4384 2.413 No - Demise See Tables 4- CubeSail 59 Socket Cap Screw 12 18-8 Stainless Steel Screw 0.6350288 5.4102 12.6111 0 Yes 1450 6 CubeSail 60 Slotted Screw 8 Nylon Screw 0.0907184 5.5626 8.0772 0 No - Demise 21.4900 CubeSail 61 Camera 2 Circuit Board Block 13.5 20.0000108 28.30068 No - Demise 002 51

Appendix E. ELaNa-19 Component List by CubeSat: DaVinci Diameter/ Row Individual Length Height High Melting CUBESAT Name Qty Material Body Type Width Survivability Number Mass (g) (mm) (mm) Temp Temp (mm) DaVinci 1 DaVinci Cubesat 1 Aluminium 6082 Box - - - - No - Demise DaVinci 2 CubeSat Structure 1 Aluminium 6082 Box 396 100 100 340.5 No - Demise DaVinci 3 Patch Antenna 1 Ceramic Disc 69 48.124 48.124 9.652 No - Demise DaVinci 4 Deployable VHF/UHF Antenna 1 Nitinol Thin strips 12 450 170 No - Demise DaVinci 5 Deployable Solar Panels 2 Copper, Fibreglass, Kapton Rectangle 332 1.6 200 300 No - Demise DaVinci 6 Solar Panels 2 Copper, Fibreglass, Kapton Rectangle 142 1.6 100 300 No - Demise DaVinci 7 Duplex Comms Payload 1 PCB PCB 226 63.73 118.7 26.99 No - Demise DaVinci 8 VUTRX Comms 1 PCB PCB 96 90.18 95.89 13 No - Demise DaVinci 9 Imaging Payload 1 PCB/Glass PCB 43 24.4 25 34.1 No - Demise DaVinci 10 Antenna Deployment Module 1 Aluminium PCB 87 98 98 10.51 No - Demise DaVinci 11 On Board Computer 1 PCB PCB 73 90.17 95.89 5.51 No - Demise DaVinci 12 Payload Interface Module 1 PCB PCB 70 90.17 95.89 23.29 No - Demise DaVinci 13 Battery 1 lithium ion polymer PCB 331 90.17 95.89 27.35 No - Demise DaVinci 14 ADCS Mother board 1 PCB PCB 86 90.17 95.89 9.06 No - Demise DaVinci 15 Reaction Wheel Daughter Board 1 Stainless Steel (120g of total) PCB/Box 239 90.17 95.89 44.49 Yes 1450 See Tables 4-6 DaVinci 16 Harnesses 20 Copper Cylinder/wire 22.5 - - - No - Demise DaVinci 17 Spacers 1 Aluminium 6082 Cylinder 16.4 - - - No - Demise DaVinci 18 Engraved Plate 1 Aluminium 6082 Rectangle 28 - - - No - Demise DaVinci 19 EPS 1 PCB PCB 178 - - - No - Demise DaVinci 20 Spacing Headers 1 - - 16 - - - No - Demise 52

Appendix F. ELaNa-19 Component List by CubeSat: ISX (1/2) Diameter/ Row Individual Length Height High Melting CUBESAT Name Qty Material Body Type Width Survivability Number Mass (g) (mm) (mm) Temp Temp (mm) ISX 1 ISX 3U CubeSat 1 Various Box 3699.3 100 100 340.5 No - Demise ISX 2 CubeSat Structure 1 Aluminum 6061 Box 456 100 100 340.5 No - Demise ISX 3 +Z Panel 1 PCB Box 30 100 100 2.5 No - Demise ISX 4 -Z Panel 1 PCB Box 30 100 100 2.5 No - Demise ISX 5 Radio Daughter Board 1 PCB Box 15 36 83 2.5 No - Demise ISX 6 GPS Daughter Board 1 PCB Box 15 39 83 2.5 No - Demise ISX 7 GPS Patch 1 Ceramic Box 11.4 25.1 25.1 5.2 No - Demise ISX 8 C-Band Patch 1 Ceramic Box 2.1 12 12 4.3 No - Demise ISX 9 Antenna Routes 3 Delrin Box 5 65 65 3.4 No - Demise ISX 10 Antenna 6 Nitonol Wire Box 2 0.31 165 0.51 No - Demise ISX 11 System Board 1 PCB Box 60 100 83 3 No - Demise ISX 12 Payload Interface and Battery Board 1 PCB Box 50 83 83 3 No - Demise ISX 13 Side Panel 4 PCB Box 120 83 320 2.5 No - Demise ISX 14 Solar Cell 20 Eglass Box 2.3 70 40 0.5 No - Demise ISX 15 Solar Angle Sensor Board 5 PCB Box 5 20 30 2.5 No - Demise ISX 16 Solar Angle Sensor Apperture 5 Aluminum Box 3 19 21 5 No - Demise ISX 17 Battery Bracket 1 Aluminum 6061 Box 168 76 82 67 No - Demise ISX 18 Heat Shrink 2 RNF-100 Polyolefin Heat Shrink Tube 2 63.5 25.4 0.5 No - Demise ISX 19 Batteries 9 Lithion Ion Cylinder 45 18.4 65.1 N/A No - Demise ISX 20 Dummy Cell 1 Delrin Cylinder 10 19 66 N/A No - Demise 53

ELaNa-19 Component List by CubeSat: ISX (2/2) Diameter/ Row Individual Length Height High Melting CUBESAT Name Qty Material Body Type Width Survivability Number Mass (g) (mm) (mm) Temp Temp (mm) ISX 21 Magnets 4 NdFeB Cylinder 5 14.3 3.2 N/A Yes 1300 See Tables 4-6 ISX 22 Historesis Material 4 HyMu80 Cylinder 2.6 2.3 50 N/A Yes 1454 See Tables 4-6 ISX 23 Magnetorquer Route 3 Delrin Box 5 78 58 4 No - Demise ISX 24 Magnetorquer Wire 3 Copper Cylinder 9 3 260 N/A No - Demise ISX 25 Screw - Representative 120 Stainless Steel 316 Cylinder 0.87 2.8 10 N/A Yes 1510 See Tables 4-6 ISX 26 Processor Housing 1 Aluminum 6061 Box 725 94.5 98.5 60 No - Demise ISX 27 Processor Board 1 1 PCB Box 87 75 89 3 No - Demise ISX 28 Processor Board 2 1 PCB Box 42 75 89 3 No - Demise ISX 29 Processor Board 3 1 PCB Box 50 75 89 3 No - Demise ISX 30 RF Front End Housing 1 Aluminum 6061 Box 225 94.5 98.5 30 No - Demise ISX 31 RF Front End Board 1 1 PCB Box 39 75 89 3 No - Demise ISX 32 RF Front End Board 2 1 PCB Box 40 75 89 3 No - Demise ISX 33 RF Front End Board 3 1 PCB Box 32 75 89 3 No - Demise ISX 34 Cband Housing 1 Aluminum 6061 Box 130 94.5 98.5 20 No - Demise ISX 35 Cband Board 1 PCB Box 44 75 89 3 No - Demise ISX 36 Payload Heat Shrink 1 Polyolefin Tube 5 20 100 0.5 No - Demise ISX 37 Payload Dialectric 1 PTFE Box 10 10 10 10 No - Demise ISX 38 SMB Connectors 4 Brass Box 5 17 6.5 14 No - Demise ISX 39 Cabling 3 Copper Ribbon 40 25.4 340 0.5 No - Demise ISX 40 Staking Compound 1 3M Scotch Weld 2216 Rectangular 50 N/A N/A N/A No - Demise ISX 41 Kapton Tape 1 Kapton Tape Tape 0 Various Various 0.05 No - Demise ISX 42 Sep/Actuating Switches 2 Plastic (PBT) Rectangular 2 6 8 7 No - Demise ISX 43 Payload Cable Bundles 1 Plastic (PBT) Cylinder 20 10 50 N/A No - Demise ISX 44 Conformal Coating 1 Arathane 5750 Coating 30 N/A N/A N/A No - Demise 54

Appendix G. ELaNa-19 Component List by CubeSat: NMTSat (1/2) Diameter/ Row Individual Length Height High Melting CUBESAT Name Qty Material Body Type Width Survivability Number Mass (g) (mm) (mm) Temp Temp (mm) NMTsat 1 3U CubeSat structure 1 Aluminum 6061 Box 396.893 99.87 99.87 340.53 No - Demise NMTsat 2 Structural Rods 4 18-8 Stainless Steel Rods 49.94 3 98 Yes 1450 See Tables 4-6 NMTsat 3 Mid plane Standoffs 4 Aluminum 6061 Box 10 99.87 99.87 7 No - Demise NMTsat 4 ISIS Antenna 1 Aluminum 6061 Box (before deployment) 85.162 98 98 5.7 No - Demise NMTsat 5 ISIS screws 4 18-8 Stainless Steel screws 0.25 4 7.8 Yes 1450 See Tables 4-6 NMTsat 6 ISIS washers 4 18-8 Stainless Steel Washer 0.05 5 0.711 Yes 1450 See Tables 4-6 NMTsat 7 GAMMA 1 FR-4 PC/104 stack 227.5 90.297 95.885 10 No - Demise NMTsat 8 GAMMA Antenna 1 Aluminum 6061 box 15 38.1 32.055 15.24 No - Demise NMTsat 9 GAMMA Antenna washers 2 18-8 Stainless Steel whasher 0.05 4.089 0.711 Yes 1450 See Tables 4-6 NMTsat 10 GAMMA Antenna screws 2 18-8 Stainless Steel screw 0.6 4 9.7 Yes 1450 See Tables 4-6 NMTsat 11 GAMMA Antenna nuts 2 18-8 Stainless Steel Nut 0.2 3 1 Yes 1450 See Tables 4-6 NMTsat 12 ACS 1 FR-4 PC/104 30 90.297 95.885 15 No - Demise NMTsat 13 Pumpkin Flight board 1 FR-4 PC/104 89.67 90.297 95.885 15 No - Demise NMTsat 14 HE-100 Radio 1 FR-4 PC/104 74.185 90.297 95.885 15 No - Demise NMTsat 15 LPP 1 FR-4 PC/104 29.6 90.297 95.885 15 No - Demise NMTsat 16 PCM 1 FR-4 PC/104 29.6 90.297 95.885 15 No - Demise NMTsat 17 CPU with BeagleBone black 1 FR-4 PC/104 69.28 90.297 95.885 30 No - Demise NMTsat 18 MAG 2 FR-4 PC/104 29.6 90.297 95.885 15 No - Demise NMTsat 19 Buffer 1 FR-4 PC/104 29.6 90.297 95.885 15 No - Demise NMTsat 20 SALLSA 3 FR-4 PC/104 stack 29.6 90.297 95.885 15 No - Demise 55

ELaNa-19 Component List by CubeSat: NMTSat (2/2) Diameter/ Row Individual Length Height High Melting CUBESAT Name Qty Material Body Type Width Survivability Number Mass (g) (mm) (mm) Temp Temp (mm) NMTsat 21 Power Board 1 FR-4 PC/104 199.58 90.297 95.885 25 No - Demise NMTsat 22 PEEK Screws 8 PEEK screw 0.16 6.756 - 9.525 No - Demise NMTsat 23 PEEK column 4 PEEK Cylinder 4.884 12.7 - 28.575 No - Demise NMTsat 24 copper plate (plasma probe) 1 101 Copper Circular Plate 32.62 60.96 - 3.175 No - Demise NMTsat 25 Stacking Bus Conector 4 Copper alloy with gold plate Box 6.34 79 12.7 10 No - Demise NMTsat 26 Solar panels 4 FR-4 Rectangualr Plate 96.65 81.73 324.5 1.575 No - Demise NMTsat 27 solar panel screw 8 18-8 stainless steel screw 0.54 6 - 7.8 Yes 1450 See Tables 4-6 NMTsat 28 solar panel nut 8 18-8 Stainless Steel nut 0.241 5.5 - 1.8 Yes 1450 See Tables 4-6 NMTsat 29 Solar panel clip 4 18-8 Stainless Steel box 1.364 15 15 0.3 Yes 1450 See Tables 4-6 NMTsat 30 15mm spacers 36 18-8 Stainless Steel hex cylinder 4.536 6 - 15 Yes 1450 See Tables 4-6 NMTsat 31 25mm spacers 16 18-8 Stainless Steel hex cylinder 11.34 6 - 25 Yes 1450 See Tables 4-6 NMTsat 32 RF cables with SSMCX connector 2 Copper alloy cable 13.608 - - - No - Demise NMTsat 33 Other Cables Copper alloy cable 10 - - - No - Demise 56

Appendix H. ELaNa-19 Component List by CubeSat: RSat Diameter/ Row Individual Length Height High Melting CUBESAT Name Qty Material Body Type Width Survivability Number Mass (g) (mm) (mm) Temp Temp (mm) Rsat 1 RSat CubeSat 1 Aluminium 6061 A-Frame 4000 113 113 340.5 No - Demise Rsat 2 CubeSat Structure 1 Aluminium 6061 A-Frame 750 100 100 340.5 No - Demise Rsat 3 Arms 2 CRP Windform XT Hollow-core 292 15 15 600 No - Demise Rsat 4 Motors 16 Stainless Steel Cylinder 19.33 12 39 N/A Yes 1450 See Tables 4-6 Rsat 5 Solar Panels 6 Fiberglass Flat pannel 100 83 340.5 1.5 No - Demise Rsat 6 Motor Control Board 32 Fiberglass Flat pannel 15 15 30 6 No - Demise Rsat 7 Batteries 6 Lithium-Ion Cylinder 91 18.3 64.8 N/A No - Demise Rsat 8 ADCS 2 HyMu 80 / Neodymium Cylinder 100 25.4 5 N/A Yes 1454 See Tables 4-6 Rsat 9 Comm Board 1 Fiberglass / Aluminium Box 350 82.5 82.5 17 No - Demise Rsat 10 Battery Frame 2 ABS Frame 30 50 65 30 No - Demise Rsat 11 C&DH Board 1 PCB Flat pannel 100 96 327.5 6 No - Demise Rsat 12 Fasteners ~150 Stainless Steel M2 Screws 1 2 Variable N/A Yes 1510 See Tables 4-6 Rsat 13 Sep Switches 2 Plastic Limit switch 10 10 10 10 No - Demise Rsat 14 Cabling - Copper alloy - - - - - No - Demise 57

Appendix I. ELaNa-19 Component List by CubeSat: Shields-1 (1/2) Diameter/ Row Individual Length Height High Melting CUBESAT Name Qty Material Body Type Width Survivability Number Mass (g) (mm) (mm) Temp Temp (mm) Shields-1 1 Shields-1 3 U CubeSat 1 - Box 6935.35 10 10 34.05 No - Demise Shields-1 2 Mid Structure-Atomic Z Grade Vault 1 - Box - - - - No See Tables 4-6 Shields-1 2.1 Shield -1 4 Aluminum 6061 Sheet 56.0099 95.403 135.9 1.6 No - Demise Shields-1 2.2 Shield 0 4 Ti-6-4 Sheet 113.7832 95.403 135.9 1.981 No 1650 See Tables 4-6 Shields-1 2.3 Shield 1 4 Tantalum Sheet 219.8909792 95.403 135.9 1.016 Yes 2980 See Tables 4-6 Shields-1 2.4 Shield 2 2 Aluminum 6061 Sheet 35.62155203 90.806 90.806 1.6 No - Demise Shields-1 2.5 Shield 3 2 Ti-6-4 Sheet 72.36452329 90.806 90.806 1.981 Yes 1650 See Tables 4-6 Shields-1 2.6 Shield 4 2 Tantalum Sheet 139.8475746 90.806 90.806 1.016 Yes 2980 See Tables 4-6 Shields-1 2.7 Shield 5 2 Aluminum 6061 Sheet 3.420275484 31.75 - 1.6 No - Demise Shields-1 2.8 Shield 6 2 Ti-6-4 Sheet 8.794904361 31.75 - 1.981 Yes 1650 See Tables 4-6 Shields-1 2.9 Shield 7 2 Tantalum Sheet 13.4277482 31.75 - 1.016 Yes 2980 See Tables 4-6 Shields-1 3 Bottom Structure-Research Payload 1 Aluminum 6061 Box 2305.392421 100 142 26.1 No - Demise Shields-1 3.1 Al-Ti Z grade Sample - - - - - - No - Demise Shields-1 3.2 - 1 Aluminum 6061 Sheet 15.00298702 66.497 - 1.6 No - Demise Shields-1 3.3 - 1 Ti-6-4 Sheet 30.4776999 66.497 - 1.981 Yes 1650 See Tables 4-6 Shields-1 3.4 Al-Ti-Ta Z grade Sample (3 g/cm2) - - - - - - No - Demise Shields-1 3.5 - 1 Aluminum 6061 Sheet 15.00298702 66.497 - 1.6 No - Demise Shields-1 3.6 - 1 Ti-6-4 Sheet 30.4776999 66.497 - 1.981 Yes 1650 See Tables 4-6 Shields-1 3.7 - 1 Ta Sheet 14.7225828 66.497 - 0.254 No - Demise Shields-1 3.8 Al-Ti-Ta Z grade Sample (3 g/cm2) - - - - - - - No - Demise Shields-1 3.9 - 1 Aluminum 6061 Sheet 15.00298702 66.497 - 1.6 No - Demise Shields-1 3.10 - 1 Ti-6-4 Sheet 30.4776999 66.497 - 1.981 Yes 1650 See Tables 4-6 Shields-1 3.11 - 1 Ta Sheet 58.8903312 66.497 - 1.016 No - Demise Shields-1 4 Top Structure-Antenna Housing 1 eg. Aluminum 6061 Box 356 100 46.7 100 No - Demise 58

ELaNa-19 Component List by CubeSat: Shields-1 (2/2) Diameter/ Row Individual Length Height High Melting CUBESAT Name Qty Material Body Type Width Survivability Number Mass (g) (mm) (mm) Temp Temp (mm) Shields-1 5 Battery Board 1 Lithium-Ion, PCB Board 310 87 87 1.6 No - Demise Shields-1 6 Antenna 1 Al 6061, PCB box 89 100 100 6.5 No - Demise Shields-1 7 FCPU and Comm Board 1 Al, PCB Board 92 87 87 1.6 No - Demise Shields-1 8 Research Payload Board 2 PCB Board 90 87 87 1.6 No - Demise Shields-1 9 EPS Board 1 PCB - 87.8 87 87 1.6 No - Demise Shields-1 9.1 Voltage Booster 1 Kovar, PCB box 75.7 30 50 10 No - Demise Shields-1 9.2 Voltage Booster Heat Sink 1 Aluminum frame 32.39 30 50 10 No - Demise Shields-1 10 Charge Dissipation Film electrodes 4 SS 305 disk 35.73 25.4 2.921 Yes 1538 See Tables 4-6 Shields-1 10.1 Charge Dissipation Film spring 1 stainless steel spring 5 6.3 12.7 - Yes 1650 See Tables 4-6 Shields-1 11 Charge Dissipation Film housing 1 Ultem Cylinder 32.8 38.1 25.4 - No - Demise Shields-1 11.1 Antenna Rf Connector 1 Copper/Gold Cable 5.01 - - - No - Demise Shields-1 11.2 Omnetics antenna Cabling 9 pin 1 Copper/Gold - 4.75 - - - No - Demise Shields-1 12 Omnetics Research Payload Cabling 3 Copper - 25 - - - No - Demise Shields-1 13 RTDs 10 Stainless Steel, Al, Cu - 1.89 - - - Yes 1650 See Tables 4-6 Shields-1 14 Microdosimeters 8 Kovar, PCB - 20 35.6 25.4 1.016 No - Demise Shields-1 15 Solar Panels 4 Triple Junction GaAs Board 112.33 83.2 317 2.108 No - Demise Shields-1 16 Fasteners 76 A86 stainless Screw 0.5171 2.845 4.7752 - Yes 1510 See Tables 4-6 Shields-1 17 Fasteners 66 A86 stainless Screw 0.5171 2.184 3.048 - Yes 1510 See Tables 4-6 Shields-1 18 Fasteners 8 A86 stainless Screw 0.5171 8 6.35 - Yes 1510 See Tables 4-6 Shields-1 19 Solar Panel Screws 24 SS 4130 Screws 0.25 1.5875 6.35 - Yes 1510 See Tables 4-6 Shields-1 19 Solar Panel Washers 24 SS 4130 Washers 1.00 3.175 1.5875 - Yes 1510 See Tables 4-6 Shields-1 20 Charge Dissipation Film 2 Acrylic - 0.03 25.4 - 0.0508 No - Demise Shields-1 21 Remove Before Flight Pin 1 Stainless Steel, Al switch 20 25.4 12.5 12.5 Yes 1510 See Tables 4-6 Shields-1 22 Sep Switch 1 PCB stainless steel switch 20 25.4 12.5 12.5 Yes 1510 See Tables 4-6 Shields-1 23 ADCS Components (eg. Magnets) 1 AlNiCo Rod 11 6.4 - 35.6 No - Demise Shields-1 24 ADCS Components (Hysteresis Rods) 3 Hymu80 Rod 13 1.588 - 70 Yes 1454 See Tables 4-6 59

Appendix J. ELaNa-19 Component List by CubeSat: STF-1 Diameter/ Row Mass (g) Length Height High Melting CUBESAT Name Qty Material Body Type Width Survivability Number (Ind) (mm) (mm) Temp Temp (mm) STF-1 1 STF-1 3U CubeSat 1 Box No - Demise STF-1 2 CubeSat Structure 1 Aluminum 6082 Box 513 100 100 340.5 No - Demise STF-1 3 UHF Antenna 1 PCB, Aluminum Box 114 102 102 7.13 No - Demise inc. w/ row STF-1 3 UHF Element 2 NiTi-Alloy Box 0.19 15.4 3.1 No - Demise 3 STF-1 4 1U Solar Panel 1 PCB Box 43 98 98 1.57 No - Demise STF-1 5 3U Solar Panel 4 PCB Box 150.5 82.6 337 1.57 No - Demise STF-1 6 Sep Switches 2 Aluminum Thin Wall Cylinder 2.35 est 5.05 11.8 No - Demise STF-1 7 GPS Antenna 1 Composite Radome/Aluminum -T6 Box 88 52.78 52.78 17.53 No - Demise inc. w/ row STF-1 8 LP Element 2 NiTi-Alloy Box 0.19 588.96 3.1 No - Demise 3 STF-1 9 Radio 1 PCB/ Aluminum Box 87 69 69 13.5 No - Demise STF-1 10 Battery 2 PCB/Lithium Polymer Box 338 90.17 95.89 26.7 No - Demise STF-1 11 EPS 1 PCB Box 178 90.17 95.89 15.4 No - Demise STF-1 12 Special Services Board 1 PCB Box 250 est 90.17 95.89 18.09 No - Demise STF-1 13 C&DH Board 1 PCB Box 89 88.88 91.98 23.25 No - Demise STF-1 14 Fasteners Stainless Steel Solid Cylinder 120 est 3.048 - Yes 1510 See Tables 4-6 STF-1 15 Cabling Copper alloy/ Teflon - 80 est - - - No - Demise STF-1 16 Connectors Tin/Gold/ABS - 96 est - - - No - Demise STF-1 17 CSEE Experiment Board 1 PCB Box 122 90.17 95.89 22.19 No - Demise STF-1 17 Ferrite Bead 1 Ferrite Box 0.03 2 1.2 0.9 Yes 1539 See Tables 4-6 STF-1 17 LED Chip Carrier 3 Al2O3 (Ceramic) Box <1.0 10.17 10.17 1.27 No - Demise STF-1 18 Physics Experiment Board 1 PCB Box 191 90.17 95.89 19 No - Demise inc. w/ row STF-1 18 Geiger Tube 2 Stainless Steel/Mica/Neon/Argon Thin Wall Cylinder 15 43 - Yes 1539 See Tables 4-6 15 STF-1 19 IMU Experiment Board 1 PCB Box 47 90.17 95.89 2.6 No - Demise STF-1 20 Camera 1 PCB Box 8 24 34 3 No - Demise inc. w/ row STF-1 20 Camera Lens 1 ABS/Glass Solid Cylinder 13.1 14.75 No - Demise 17 STF-1 21 Debug Port 1 Aluminum/Silicon/Copper Box 44 10.5 33.6 7.5 60

Appendix K. ELaNa-19 Component List by CubeSat: TOMSat EAGLESCOUT Diameter/ Row Individual Length Height High Melting CUBESAT Name Qty Material Body Type Width Survivability Number Mass (g) (mm) (mm) Temp Temp (mm) TOMSat EAGLEScout 1 Full Body Only 1 6061-T6 Box 644 103.494 110.9 340.5 No - Demise TOMSat EAGLEScout 2 Frame Part 1 (2001) 1 6061-T6 Box 298 103.494 110.9 130 No - Demise TOMSat EAGLEScout 3 Frame Part 2 (4001) 1 6061-T6 Box 346 103.494 110.9 209.23 No - Demise TOMSat EAGLEScout 4 Bus Electronics 1 FR4 Box 627 85.046 84.882 97.05 No - Demise TOMSat EAGLEScout 5 Reaction Wheels 1 Stainless Box 225 52.832 71.102 39.192 Yes 1450 See Tables 4-6 TOMSat EAGLEScout 6 Star Tracker 2 6061-T6 (65%), glass (25%), FR4 (10%) Box 55 26.67 25.4 41.829 No - Demise TOMSat EAGLEScout 7 Single Torque Rod 9 HyMu 80 Cylinder 18 8 78.74 - Yes 1300 See Tables 4-6 TOMSat EAGLEScout 8 Zenith Lid Assembly 1 6061-T6 Box 141 103.494 110.9 16.74 No - Demise TOMSat EAGLEScout 9 Antenna 2 Ceramic (95%) with copper foil (5%) Plate 16 39.878 38.099 3.277 No - Demise TOMSat EAGLEScout 10 Wing Assembly 2 6061-T6 Plate 148 2.677 313.5 73.66 No - Demise TOMSat EAGLEScout 11 Nadir Lid Assembly 1 6061-T6 Box 100 103.494 110.9 7.977 No - Demise TOMSat EAGLEScout 12 Antenna 1 Ceramic (95%) with copper foil (5%) Plate 16 39.878 38.099 3.277 No - Demise TOMSat EAGLEScout 13 Uplink Receiver 1 6061-T6 (75%), glass (25%) Cylinder 28 31 31.601 - No - Demise TOMSat EAGLEScout 14 Payload Assembly 1 6061-T6 (45%), glass (45%), FR4 (10%) Box 1311 82.444 164.58 56.238 No - Demise TOMSat EAGLEScout 15 18267 1 Titanium Cylinder 17 32 37.275 - Yes 1650 See Tables 4-6 TOMSat EAGLEScout 16 18265 1 Titanium Cylinder 11 32 16.506 - Yes 1650 See Tables 4-6 TOMSat EAGLEScout 17 18264 1 Titanium Cylinder 12 32 25.999 - Yes 1650 See Tables 4-6 TOMSat EAGLEScout 18 18268 1 Titanium Cylinder 4 39 2.5 - Yes 1650 See Tables 4-6 TOMSat EAGLEScout 19 18266 1 Titanium Cylinder 10 32 5.081 - Yes 1650 See Tables 4-6 TOMSat EAGLEScout 20 18263 1 Titanium Cylinder 1 32 1.649 - Yes 1650 See Tables 4-6 TOMSat EAGLEScout 21 18270 1 Titanium Cylinder 1 32 1.601 - Yes 1650 See Tables 4-6 TOMSat EAGLEScout 22 Laser 1 6061-T6 (90%), stainless steel (10%) Box 353 82.245 120.65 20.192 Yes ~1650 See Tables 4-6 TOMSat EAGLEScout 23 STIM 210 IMU 1 6061-T6 Box 116 48.26 64.77 25.4 No - Demise 61

Appendix L. ELaNa-19 Component List by CubeSat: TOMSat R3 Diameter/ Row Individual Length Height High Melting CUBESAT Name Qty Material Body Type Width Survivability Number Mass (g) (mm) (mm) Temp Temp (mm) TOMSat R3 1 Full Body Only 1 6061-T6 Box 644 103.494 110.9 340.5 No - Demise TOMSat R3 2 Frame Part 1 (2001) 1 6061-T6 Box 298 103.494 110.9 130 No - Demise TOMSat R3 3 Frame Part 2 (4001) 1 6061-T6 Box 346 103.494 110.9 209.23 No - Demise TOMSat R3 4 Bus Electronics 1 FR4 Box 627 85.046 84.882 97.05 No - Demise TOMSat R3 5 Reaction Wheels 1 Stainless Box 225 52.832 71.102 39.192 Yes 1450 See Tables 4-6 TOMSat R3 6 Star Tracker 2 6061-T6 (65%), glass (25%), FR4 (10%) Box 55 26.67 25.4 41.829 No - Demise TOMSat R3 7 Single Torque Rod 9 HyMu 80 Cylinder 18 8 78.74 - Yes 1300 See Tables 4-6 TOMSat R3 8 Zenith Lid Assembly 1 6061-T6 Box 141 103.494 110.9 16.74 No - Demise TOMSat R3 9 Antenna 2 Ceramic (95%) with copper foil (5%) Plate 16 39.878 38.099 3.277 No - Demise TOMSat R3 10 Wing Assembly 2 6061-T6 Plate 148 2.677 313.5 73.66 No - Demise TOMSat R3 11 Nadir Lid Assembly 1 6061-T6 Box 100 103.494 110.9 7.977 No - Demise TOMSat R3 12 Antenna 1 Ceramic (95%) with copper foil (5%) Plate 16 39.878 38.099 3.277 No - Demise TOMSat R3 13 Uplink Receiver 1 6061-T6 (75%), glass (25%) Cylinder 28 31 31.601 - No - Demise TOMSat R3 14 Payload Assembly 1 6061-T6 (45%), glass (45%), FR4 (10%) Box 1311 82.444 164.58 56.238 No - Demise TOMSat R3 15 18267 1 Titanium Cylinder - Hollow 17 32 37.275 - Yes 1650 See Tables 4-6 TOMSat R3 16 18265 1 Titanium Cylinder - Hollow 11 32 16.506 - Yes 1650 See Tables 4-6 TOMSat R3 17 18264 1 Titanium Cylinder - Hollow 12 32 25.999 - Yes 1650 See Tables 4-6 TOMSat R3 18 18268 1 Titanium Cylinder - Hollow 4 39 2.5 - Yes 1650 See Tables 4-6 TOMSat R3 19 18266 1 Titanium Cylinder - Hollow 10 32 5.081 - Yes 1650 See Tables 4-6 TOMSat R3 20 18263 1 Titanium Cylinder - Hollow 1 32 1.649 - Yes 1650 See Tables 4-6 TOMSat R3 21 18270 1 Titanium Cylinder - Hollow 1 32 1.601 - Yes 1650 See Tables 4-6 TOMSat R3 22 Laser 1 6061-T6 (90%), stainless steel (10%) Box 353 82.245 120.65 20.192 Yes ~1650 See Tables 4-6 TOMSat R3 23 STIM 210 IMU 1 6061-T6 Box 116 48.26 64.77 25.4 No - Demise 62

Appendix M. ELaNa-19 Component List by CubeSat: GEOStare (1/2) Hig Diameter/ Lengt Row Qt Individua Height h Melting CUBESAT Name Material Body Type Width h Survivability Number y l Mass (g) (mm) Tem Temp (mm) (mm) p GEOstare 1 GEOstare 1 Aluminum 6061-T6 Box 4207 226 340 100 No - Demise GEOstare 2 GEOstare PX Panel 1 Aluminum 6061-T6 Box 162 82 335 10 No - Demise GEOstare 3 CGEOstare MX Panel 1 Aluminum 6061-T6 Box 151 82 335 11.5 No - Demise GEOstare 4 CIERO PZ Panel 1 Aluminum 6061-T6 Box 272 100 209 20 No - Demise GEOstare 5 GEOstare PY Panel 1 Aluminum 6061-T6 Box 172 226 330 11.5 No - Demise GEOstare 6 GEOstare MY Panel 1 Aluminum 6061-T6 Box 172 226 330 11.5 No - Demise GEOstare 7 IRM Structure 1 Aluminum 6061-T6 Box 57 100 100 50 No - Demise GEOstare 8 IMU 1 Copper Alloy Box 18 24.5 38 11.1 No - Demise GEOstare 9 RWA_Motor_Flywheel 3 Bronze C1800 Cylinder 20 40 13 No - Demise GEOstare 10 RWA_Motor 3 Copper Alloy Cylinder 15 40 13 No - Demise GEOstare 11 RWA_Brackets 3 Aluminum 6061-T6 Box 10 40 40 13 No - Demise GEOstare 12 Torque Coils (Housing) 3 Delrin Box 31 46 63 4 No - Demise GEOstare 13 Torque Coils (Winding) 3 Copper Alloy Box 7 46 63 4 No - Demise GEOstare 14 Star Trackers (Housing) 2 Aluminum 6061-T6 Box 26 33 38 22 No - Demise GEOstare 15 Star Trackers (PCB) 2 Copper Alloy Box 5 38 38 1.5 No - Demise GEOstare 16 Star Trackers (Lens) 2 Glass Cylinder 10 40 16 No - Demise GEOstare 17 C&DH Board 1 Copper Alloy Box 128 80 82 3 No - Demise Battery Module GEOstare 18 1 Aluminum 7075-T6 Box 62 42 86 42 No - Demise Structure GEOstare 19 Battery Board 1 Copper Alloy Box 8 38.2 83.75 1.58 No - Demise GEOstare 20 Batteries 6 Stainless Steel (generic) Cylinder 47 18 65 Yes 1510 See Table 4-6 63

ELaNa-19 Component List by CubeSat: GEOStare (2/2) Diameter/ Row Individual Length Height High Melting CUBESAT Name Qty Material Body Type Width Survivability Number Mass (g) (mm) (mm) Temp Temp (mm) GEOstare 21 UHF_assembly 1 Copper Alloy Box 80 50 100 50 No - Demise GEOstare 22 UHF_radio 1 Aluminum 6061-T6 Box 30 36 83 7 No - Demise GEOstare 23 UHF_antenna 1 Copper Alloy Box 52 98 98 7 No - Demise GEOstare 24 OEM615 1 Copper Alloy Box 25 60 100 9 No - Demise GEOstare 25 GPS_housing 1 Aluminum 6061-T6 Box 136 60 150 30 No - Demise GEOstare 26 Payload Structure 1 Aluminum 6061-T6 Box 23.88 100 150 100 No - Demise GEOstare 27 Telescope baffle 1 Titanium Cylinder 96.1 d=93.0 - 51 Yes 1650 See Table 4-6 GEOstare 28 Telescope 1 Fused Silica Cylinder 620 d=89.5 - 49.2 Yes 1600 See Table 4-6 GEOstare 29 Telescope enclosure 1 Invar-36 Cylinder 396 d=91.8 - 67 No - Demise GEOstare 30 ImagerAssembly 1 Copper Alloy Box 247 100 100 20 No - Demise GEOstare 31 Fasteners 200 Steel A-286 Cylinder 0.5 4.64 6.35 Yes 1430 See Table 4-6 GEOstare 32 Flat-Flex Connectors 6 Copper Alloy Box 20 20 100 2 No - Demise GEOstare 33 Wired Harnessing 250 Copper Alloy Cylinder 1 2 100 No - Demise 64

Appendix N. ELaNa-19 Component List by CubeSat: SHFT-1 Row Body Individual Diameter/ Length Height High Melting CUBESAT Name Qty Material Survivability Number Type Mass (g) Width (mm) (mm) (mm) Temp Temp SHFT-1 1 3U CubeSat 1 Box 5100 113.1 365.8 112.48 No - Demise SHFT-1 2 CubeSat Structure 1 Al 7075-T651 Box 378.7 100 270.7 100 No - Demise SHFT-1 3 Antenna - deployed 4 Steel, Ultem, Al 6061 Boom 458.1 19.05 6000 0.28 No - Demise SHFT-1 4 Solar Panels - deployed 2 FR4, glass, Al 6061 Flat Plate 305 138.38 326.49 57.25 No - Demise SHFT-1 5 ADCS 1 Al 6061 Box 895 100 100 50 No - Demise SHFT-1 6 UHF/GPS Antenna System - deployed 1 Al 6061, brass, RO3006 005 R3 Box 260.3 274 274 115.42 No - Demise SHFT-1 7 S-Band Antenna 1 AD350A, RO450F, RO4003C Box 75 83.82 83.82 5.08 No - Demise SHFT-1 8 Rails 2 Al 7075-T651 Flat Plate 39.9 13.5 366 2.95 No - Demise SHFT-1 9 IXC/GPS Board 1 Polyimide Box 107.2 95.88 90.17 15.75 No - Demise SHFT-1 10 SBC Board 1 Polyimide Flat Plate 88.5 95.88 90.17 10.9 No - Demise SHFT-1 11 EPS Boards with Spacers 1 Polyimide, Al 6061 Box 218.6 95.88 90.17 24.94 No - Demise SHFT-1 12 Battery Assembly 1 Polyimide, Al 6061, 2200SF gap pad, Li Ion Box 298.6 95.88 90.17 27.35 No - Demise SHFT-1 13 Radio 1 OFHC Copper, Al 6061, Polyimide Box 576 96.65 96.65 30.91 No - Demise SHFT-1 14 Payload Boards 1 Polyimide, Al 7075 Box 1093.9 116 96.65 76 No - Demise SHFT-1 15 Internal Fasteners 85 18-8 SSTL, 316 SSTL, Alloy Steel cylinder 1 3 (head 5mm) 10 Yes 1400 See Table 4-6 SHFT-1 16 External Fasteners 134 18-8 SSTL, 316 SSTL cylinder 1 3 (head 5mm) 10 Yes 1400 See Table 4-6 SHFT-1 17 External Covers 6 Al 6061 flat plate 3.4 1.60 20 40 No - Demise SHFT-1 18 Internal Cabling Copper Alloy wires 50 0.5 150 No - Demise 65


Document Created: 2017-03-28 10:13:28
Document Modified: 2017-03-28 10:13:28
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC